Content      ..     3      4      5      6     ..

Renault Express (2023 year). Manual in english - page 5

LEVELS, FILTERS (1/3)

Level

Topping up

1

It is normal for the level to drop as the

After any operation on the hydraulic cir-

brake shoes become worn, but it must

cuit, a specialist must replace the fluid.

never drop lower than the “MINI” warn-

Only use fluids approved by the

ing line shown on brake fluid reser-

Technical Department and which have

voir 1.

been taken from a sealed container.

If you wish to check the disc and drum

Replacement intervals

wear yourself, you should obtain the

document explaining the checking pro-

Refer to the Maintenance Document for

cedure from the approved dealer net-

your vehicle.

work or from the manufacturer’s web

site.



Brake fluid

If there is an abnormal or repeated

drop in the fluid level, please consult

This should be checked frequently,

an authorised dealer.

and immediately if you notice even the

slightest loss in braking efficiency.

The level should be read with the engine

switched off and on level ground.

Please note when work-

ing close to the engine that

it may be hot. In addition,

the engine cooling fan may

Before carrying out any

come on at any moment. The y

action in the engine com-

label in the engine compartment re-

partment, you must switch

minds you of this.

off the ignition. ➥ 2.3.

Risk of injury.

4.9

CarManuals2.co

LEVELS, FILTERS (2/3)

Checking intervals

Check the coolant level regularly



Power steering liquid

(very severe damage is likely to be

fluid

2

caused to the engine if it runs out of

For maintenance operations on the

coolant).

power-assisted steering, contact an ap-

If the level needs to be topped up, only

proved dealer.

use products approved by our Technical

Department which ensure:

- antifreeze protection;

- anti-corrosion protection of the cool-

ing system.

Replacement intervals

Refer to the Maintenance Service

Booklet for your vehicle.



Coolant

With the engine switched off and on

level ground, the level when cold must

be between the MINI and MAXI marks

on reservoir 2.

Consult an approved dealer at once

Top this level up when cold before it

if you notice an abnormal or re-

reaches the MINI mark.

peated drop in any of the fluid levels.

No operations should be

carried out on the cooling

circuit when the engine is

hot.

If you feel any variation in the ef-

fectiveness of the power-assisted

Risk of burns.

steering, consult an authorised

dealer.

4.10

CarManuals2.co

LEVELS, FILTERS (3/3)

Fluid

Filters

Windscreen washer fluid. In winter, use

The replacement of filter elements (air

anti-freeze product. Use products rec-

filter, cabin filter, diesel fuel filter, etc.)

3

ommended by an authorised dealer.

is scheduled in the maintenance opera-

tions for your vehicle.

Jets To adjust the height of the wind-

screen washer jets, please consult an

Replacement intervals for filter ele-

authorised dealer.

ments: please refer to your vehicle’s

maintenance document.



Windscreen washer

reservoir

Filling: With the engine switched off,

open the cap 3, fill until you can see the

fluid, then refit the cap.

Please note when work-

Note: check the reservoir level regu-

ing close to the engine that

larly and top up the liquid before taking

it may be hot. In addition,

a trip.

the engine cooling fan may

This reservoir supplies the front and

come on at any moment. The y

rear headlight screen washers (if the

When working in the engine

label in the engine compartment re-

vehicle is equipped with them).

compartment, ensure that

minds you of this.

the windscreen wiper stalk

Risk of injury.

is in the park position.

Risk of injury.

4.11

CarManuals2.co

BATTERY (1/2)

The charge status of your battery can

Replacing the battery

decrease especially if you use your ve-

hicle:

-

for short journeys;

For your own safety and for

the proper operation of the

–

for driving in town;

1

vehicle’s electrical equip-

–

when the temperature drops;

ment

(lights, windscreen

wipers, ABS, etc.), any intervention

–

after extended use of consumers

on the battery (removal, disconnec-

(radio etc.) with the engine switched

tion, etc.) must categorically be per-

off.

formed by a specialist professional.

Risk of serious burns or electric

shocks.

You must respect the replacement

intervals (without exceeding them)

Battery 1 does not require any mainte-

as stated in the maintenance docu-

nance. You should not open it or add

ment.

any fluid.

The battery is a specific type:

ensure that it is replaced by the

same type.

Handle the battery with

care as it contains sulphu-

Call an approved Dealer.

ric acid, which must not

come into contact with eyes

or skin. If it does, wash the affected

area with plenty of water and see a

doctor if necessary.

Ensure that naked flames, red hot

objects and sparks do not come into

Before

carrying

out

any

contact with the battery as there is a

action in the engine com-

risk of explosion.

partment, you must switch

off the ignition. ➥ 2.3.

4.12

CarManuals2.co

BATTERY (2/2)

A

2

3

4

A

7

6

5

Label A

Observe the indications on the battery:

- 2 Naked flames and smoking are for-

bidden;

- 3 Eye protection required;

Please note when work-

- 4 Keep away from children;

ing close to the engine that

it may be hot. In addition,

- 5 Explosive materials;

the engine cooling fan may

- 6 Refer to the handbook;

come on at any moment. The y

– 7 Corrosive materials.

label in the engine compartment re-

minds you of this.

Risk of injury.

4.13

CarManuals2.co

TYRE INFLATION PRESSURES (1/2)

Vehicle fitted with a tyre pressure

monitoring system

In the event of under-inflation (punc-

A

tures, under-inflation etc.), the 

warning light appears on the instrument

B

panel ➥ 2.18.

C

E

F

A

C

E

F

D

E F

G

Label A

B: dimension of the tyres fitted to the

vehicle.

Open the door to read it.

Tyre pressures should be checked

C: intended driving speed.

Vehicle used fully laden

when the tyres are cold.

D : recommended pressure for optimis-

(Maximum Permissible

If the tyre pressures cannot be checked

ing fuel consumption.

All-up Weight) and

when the tyres are cold, increase the

NB: driving comfort may be altered.

towing a trailer

pressures by from 0.2 to 0.3 bar (or 3

E: front tyre pressure.

The maximum speed must be lim-

PSI). Never deflate a hot tyre.

ited to 62 mph (100 km/h) and the

F: rear tyre pressure.

tyre pressure increased by 0.2 bar

G: tyre pressure for the emergency

➥ 6.9.

spare wheel.

Risk of tyre blowouts.

4.14

CarManuals2.co

PUNCTURE, EMERGENCY SPARE WHEEL (1/4)

In case of puncture

Depending on the vehicle, a tyre infla-

tion kit or emergency spare wheel is

provided (refer to the following pages).

Do not leave the tools unsecured inside the vehicle as they may come

Vehicle fitted with a tyre pressure

loose under braking. After use, make sure the tools are correctly posi-

monitoring system

tioned in their mountings: risk of injury.

In the event of under-inflation (punc-

If bolts are supplied with the emergency spare wheel, you must use these

bolts only for the emergency spare wheel.

tures, under-inflation etc.), the 

The jack is designed for wheel changing purposes only. Under no circumstances

warning light appears on the instrument

should it be used for carrying out repairs underneath the vehicle or to gain access

panel. ➥ 2.18.

to the underside of the vehicle.

If the emergency spare wheel has been stored for several years, have it

checked by your Dealer to ensure that it is safe to use.

Vehicle fitted with an emergency spare wheel that differs from the

other wheels:

- Never fit more than one emergency spare wheel to the same vehicle.

- Replace the emergency spare wheel as soon as possible with a wheel identi-

cal to the original one.

If the vehicle is parked on

- When this is fitted to the vehicle, which must only be a temporary measure, the

the hard shoulder, you must

driving speed must not exceed the speed indicated on the label on the wheel.

warn other road users of

- Fitting an emergency spare wheel may alter the way the vehicle usually runs.

your vehicle’s presence

Avoid sudden acceleration or deceleration and reduce your speed when cor-

with a warning triangle or with other

nering.

devices as per the legislation apply-

ing to the country you are in.

- If you need to use snow chains, fit the emergency spare wheel to the rear axle

and check the tyre pressure.

5.2

CarManuals2.co

PUNCTURE, EMERGENCY SPARE WHEEL (2/4)

Depending on the vehicle, there are

2 storage options for the emergency

spare wheel:

1

- in a cradle under the floor at the rear

1

of the vehicle;

2

- the floor at the rear of the vehicle.

Emergency spare wheel 3

This is stored in cage 5 under the floor

at the rear of the vehicle.

To access emergency spare wheel 3

3

- Open the boot lid;

5

4

- remove blanking cover 2;

To store the wheel 3 in the cage

If the cradle 5 cannot be re-attached,

- undo screw with the wheelbrace 1

this may mean that the wheel is not cor-

- Make sure you reposition the wheel

stored in the boot;

rectly positioned. If this happens, open

in the cradle 5, valve pointing down-

the cage, push the wheel in as far as it

- unhook 5 cradle by taking it from

wards;

will go and close again.

hook 4;

- re-attach the cradle using handle 4

- remove emergency spare wheel.

and retighten the nut using span-

ner 1 to refit the assembly and put

blanking cover back in place;

- make sure you lock the cradle 5 back

in place.

Do not touch the exhaust.

Risk of burns.

5.3

CarManuals2.co

PUNCTURE, EMERGENCY SPARE WHEEL (3/4)

9

10

11

1

A

B

7

8

7

6

Emergency spare wheel 7

To access emergency spare wheel 7

- from the outside of the vehicle, pull

the wheel in order to access the

It is located under the floor at the rear

- Open the boot lid;

handle 11;

of the vehicle. In the event of a punc-

- remove the blanking cover 6;

ture if your vehicle is fitted with a towbar

- turn the handle 11 (movement B)

- only use the wheel brace 1 (using

in order to free the cable from the

and/or if the luggage compartment

a different tool could damage the

part 9;

is loaded, to remove the emergency

mechanism) to unroll the retaining

spare wheel from its winch you must lift

- lift the part 9 from the wheel 7;

cable. Unscrew the nut in a clock-

the vehicle using a jack at the jacking

wise direction (movement A), and

- remove the part 9 via the slot 10;

point nearest the wheel.

the wheel will lower to the ground;

- stand the wheel up, pass the cable

and the component 8 through the

wheel rim and release the wheel.

Do not touch the exhaust.

Risk of burns.

5.4

CarManuals2.co

PUNCTURE, EMERGENCY SPARE WHEEL (4/4)

9

10

C

11

1

D

7

8

7

12

To refit the wheel 7

From the luggage compartment, tighten

As the punctured wheel

To carry out this operation, the cable

the nut fully in an anti-clockwise direc-

is wider than the emer-

must be unwound.

tion (movement C) in order to wind up

gency spare wheel, when

- Stand the wheel up with the valve 12

the retaining cable, ensuring that the

you place the punctured

towards you.

wheel remains horizontal and the cable

wheel in the emergency spare

- Thread the cable and the compo-

taut.

wheel bay, the vehicle’s ground

nent 8 through the wheel rim.

Final tightening must be carried out with

clearance is reduced. To pre-

- Position wheel valve 12 towards the

the spanner 1 in the horizontal position.

vent damage, proceed carefully

ground.

when driving over raised sections

- Insert the cable in the slot 10 up to

Refit the 6 blanking cover.

of road and when dismounting

the centre of the part 9.

pavements When this is fitted to

- Insert the part 9 into the wheel 7.

the vehicle, which must only be

- Turn the handle 11 (movement D) to

a temporary measure, the driv-

lock the cable.

ing speed must not exceed the

speed indicated on the label on

the wheel.

5.5

CarManuals2.co

TYRE PRESSURE KIT (1/3)

The kit is only approved for

B

inflating the tyres of the ve-

A

hicle originally equipped

with the kit.

Do not attempt to use the

It must never be used to inflate

inflation kit if the tyre has

the tyres of another vehicle, or any

been damaged as a result

other inflatable object (rubber ring,

of driving with a puncture.

rubber boat, etc.).

You should therefore carefully check

Avoid spillage on skin when han-

the condition of the tyre sidewalls

dling the repair product bottle. If

before any operation.

droplets do leak out, rinse them off

with plenty of water.

Driving with underinflated, flat or

punctured tyres can be dangerous

Keep the repair kit away from chil-

and may make the tyre impossible

dren.

to repair.

Do not dispose of the empty bottle

The kit repairs tyres with

This repair is temporary

in the countryside. Return it to your

tread A damaged by ob-

approved dealer or to a recycling or-

jects smaller than 4 mm. It

A tyre which has been punctured

ganisation.

cannot repair all types of

should always be inspected (and re-

puncture, such as cuts of more than

paired, where possible) as soon as

The bottle has a limited service

4 mm, or cuts in tyre sidewall B etc.

possible by a specialist.

life which is indicated on its label.

Check the expiry date.

Ensure also that the wheel rim is in

When replacing a tyre repaired with

good condition.

this kit, you must consult a special-

Contact an approved dealer to re-

ist. When driving, vibration may be

place the inflation tube and repair

Do not pull out the foreign body

felt due to the presence of the repair

product bottle.

causing the puncture if it is still in

the tyre.

product injected into the tyre.

5.6

CarManuals2.co

TYRE PRESSURE KIT (2/3)

With the engine running and the

If a minimum pressure of 1.8 bar is

parking brake applied,

not reached after 15 minutes, repair

–

Disconnect any accessories previ-

is not possible; do not drive the ve-

ously connected to the vehicle’s ac-

hicle but contact an approved dealer.

1

cessories sockets;

-

refer to the information on the in-

flation kit compressor located in

the luggage compartment of the ve-

hicle and follow the instructions;

-

inflate the tyre to the recommended

pressure ➥ 4.14 ;

2

-

after a maximum of 15 minutes, stop

Before using this kit, park

inflating and read the pressure (on

the vehicle at a sufficient

pressure gauge 2).

distance from traffic, switch

on the hazard warning

Note: while the bottle is emptying

lights, apply the handbrake, ask all

(approximately

30 seconds), the

Depending on the vehicle, in the event

passengers to leave the vehicle and

pressure gauge 2 will briefly indicate

of a puncture, use the kit located in the

keep them away from traffic.

a pressure of 6 bar, then the pres-

boot or underneath the luggage com-

sure drops;

partment carpet.

-

Adjust the pressure: to increase it,

Vehicle fitted with a tyre pressure

continue inflation with the kit. To

monitoring system.

reduce it, press the button 1.

In the event of under-inflation (punc-

If the vehicle is parked on

tures, under-inflation etc.), the 

the hard shoulder, you must

warning light appears on the instrument

warn other road users of

panel. ➥ 2.18.

your vehicle’s presence

with a warning triangle or with other

devices as per the legislation apply-

ing to the country you are in.

5.7

CarManuals2.co

TYRE PRESSURE KIT (3/3)

- Start immediately and drive at a

speed between 12 to 37 mph (20 to

3

60 km/h) in order to distribute the

product evenly in the tyre; after driv-

ing a distance of 2 miles (3 km), stop

and check the pressure.

Please be aware that a

- If the pressure is higher than 1.3 bar

poorly tightened or miss-

but lower than the recommended

ing valve cap can make the

pressure (refer to the label affixed to

tyres less airtight and may

the edge of the driver’s door), adjust

lead to pressure loss.

it. Otherwise, contact an approved

Always use valve caps identical to

dealer: the tyre cannot be repaired.

those fitted originally and tighten

them fully.

Precautions when using the

kit

Once

the

tyre is

correctly inflated,

The kit should not be operated for more

remove the kit: unclip the inflation

than 15 consecutive minutes.

adapter slowly from the container 3 to

The container must be replaced after

Following repair with the kit,

prevent any product spatter and store

the first use even if liquid remains

do not travel further than

the container in plastic packaging to

inside.

120 miles (200 km). In addi-

prevent product leaks.

tion, reduce your speed and

- Affix the driving recommendation

under no circumstances exceed

label (located under the container) to

48 mph (80 km/h). The sticker,

the dashboard where the driver can

which you must affix in a prominent

see it.

position on the dashboard, reminds

- Put the kit away.

you of this.

Nothing should be placed

- At the end of this initial inflation op-

Depending on the country or local

around the driver’s feet

eration, air will still escape from the

legislation, a tyre repaired with the

as such objects may slide

tyre. You must drive a short distance

inflation kit may need to be replaced.

under the pedals during

in order to seal the hole.

sudden braking manoeuvres and

obstruct their use.

5.8

CarManuals2.co

TOOLS

Wheelbrace 4

2

5

1

This locks and unlocks the wheel bolts

and the access to emergency spare

1

wheel.

4

2

3

Tow eye 3

➥ 5.37

4

3

Accessing the tools

Hubcap tool 2

The presence of the tools depends on

This tool is used to remove the wheel

the vehicle.

trims. Located behind the jack.

The tools are located in the luggage

compartment.

Jack 1

To use the jack, unscrew nut 5. When

replacing the jack, fold it down correctly

Do not leave the tools unsecured inside the vehicle as they may come

(being sure to put the handle back in

loose under braking. After use, make sure the tools are correctly posi-

position) and replace it in its housing.

tioned in their mountings: risk of injury.

Tighten the nut 5 to secure the jack.

If bolts are supplied with the emergency spare wheel, it is imperative that

they are used and that they are used for the emergency spare wheel only: refer

to the label affixed to the emergency spare wheel.

The jack is designed for wheel changing purposes only. Under no circumstances

should it be used for carrying out repairs underneath the vehicle or to gain access

to the underside of the vehicle.

5.9

CarManuals2.co

WHEEL TRIMS

3

4

D

C

B

1

A

1

2

Wheel trim with concealed

Wheel trim 3

Central wheel trim with

wheel bolts

visible wheel bolts

Remove using hubcap tool 1 (located in

(Wheel trim 4)

Remove the wheel trim using hubcap

the tool kit) by engaging the hook in the

tool 1, (located in the tool kit) by en-

opening near the edge of the trim.

The bolts are directly accessible.

gaging the hook in the opening near

To refit, position the trim attachments

valve 2.

facing the wheel attachments and

To refit the wheel trim, align it with

press hard in the middle of the trim to

valve 2. Push the retaining hooks in fully,

clip it to the wheel.

starting on the side of valve A, followed

by B and C, finishing at Dopposite the

valve.

5.10

CarManuals2.co

CHANGING A WHEEL (1/2)

Vehicles equipped with a jack

Place the jack 4 horizontally; the jack

head must be lined up with the sill 1

and wheelbrace

closest to the wheel concerned, as

If necessary, remove the hubcap.

shown by arrow 2.

2

Use the wheelbrace 3 to slacken off

Crank up the jack 4 by hand at first to

1

the wheel bolts. Fit it so that you press

align the base plate (which should be

downwards rather than pulling up-

inclined further inwards than the jack

wards.

head).

3

Continue to crank the jack so that the

baseplate is correctly positioned

(it

should be underneath the vehicle and

aligned with the jack head).

Turn the wheelbrace until the wheel lifts

4

off the ground.

Switch on the hazard warn-

ing lights.

Keep the vehicle away from

If the vehicle is parked on

traffic and on a level surface

the hard shoulder, you must

where it will not slip.

warn other road users of

Apply the parking brake and engage

your vehicle’s presence

a gear (first or reverse).

with a warning triangle or with other

To prevent any risk of injury

devices as per the legislation apply-

Ask all passengers to leave the ve-

or damage to the vehicle,

ing to the country you are in.

only crank the jack until the

hicle and keep them away from traf-

fic.

wheel you are replacing is

a maximum of 3 centimetres off the

ground.

5.11

CarManuals2.co

TYRES (1/3)

Tyre and wheel safety

When the tyre tread has been worn to

1

the level of the wear indicators, they

The tyres are the only contact between

become visible 2: it is then necessary

the vehicle and the road, so it is essen-

to replace your tyres because the tread

tial to keep them in good condition.

rubber is 1.6 mm deep at most, re-

You must make sure that your tyres

sulting in poor road-holding on wet

conform to local road traffic regulations.

roads.

An overloaded vehicle, long journeys

by motorway, particularly in very hot

weather, or continual driving on poorly

2

surfaced minor roads will lead to more

rapid tyre wear and affect safety.

For your safety, please re-

spect the speed limit.

When they need to be re-

placed, only tyres of the

same make, size, type and profile

Maintaining the tyres

should be used on a single axle.

The tyres must be in good condition

They must either have a load ca-

and the tread form must have sufficient

pacity and speed rating at least

depth; tyres approved by our Technical

equal to those of the original

Department have wear warning strips 1

tyres, or be recommended by an

which are indicators moulded into

authorised dealer.

the tread at several points.

Failure to heed these instructions

Incidents which occur when

could endanger your safety and

driving, such as striking the

affect your vehicle’s roadworthi-

kerb, may damage the tyres

ness.

and wheel rims, and could

Risk of loss of control of the ve-

also lead to misalignment of the

hicle.

front or rear axle geometry.

In this case, have the condition of

these checked by an approved

dealer.

5.13

CarManuals2.co

HEADLIGHTS: changing bulbs (1/2)

Direction indicators

Turn the bulb holder 2 a quarter of a

1

turn and take out the bulb.

Type of bulb: PY21W.

B

A

3

2

To comply with current legislation, or

Dipped beam headlights

Main beam headlights

as a precaution, you can obtain an

emergency kit from your approved

Remove cover A.

Remove cover B.

dealer containing a set of spare

Tilt bulb holder 3 to release it and then

Tilt bulb holder 1 to release it and then

bulbs and fuses.

replace the bulb.

replace the bulb.

Type of bulb: H7.

Type of bulb: H7.

Do not touch the bulb glass. Hold it

After replacing the bulb, please ensure

by its base.

Please note when work-

that the lights are adjusted by a profes-

It is essential to use anti-U.V. 55W

ing close to the engine that

sional.

bulbs so as not to damage the plastic

it may be hot. The engine

on the headlights. Mark the bulb’s po-

cooling fan may also start

sition before removal to ensure correct

positioning when replacing.

at any moment. The 

label

When the bulb has been changed,

in the engine compartment reminds

make sure you refit the cover correctly.

you of this.

The bulbs are under pres-

sure and can break when

Risk of injury.

replaced.

Risk of injury.

5.16

CarManuals2.co

HEADLIGHTS: changing bulbs (2/2)

4

Before carrying out any

action in the engine com-

partment, you must switch

off the ignition. ➥ 2.3.

Daytime running light, front

LED side light 4

Please see an authorised dealer.

Any operation on (or mod-

ification to) the electrical

system must be performed

by an approved dealer

since an incorrect connection might

damage the electrical equipment

(harness, components and in par-

ticular the alternator). In addition,

your Dealer has all the parts re-

quired for fitting these units.

5.17

CarManuals2.co

FOG LIGHTS: changing bulbs

Any operation on (or mod-

1

2

ification to) the electrical

system must be performed

by an approved Dealer

since an incorrect connection might

damage the electrical equipment

(harness, components and in par-

ticular the alternator). In addition,

your Dealer has all the parts re-

quired for fitting these units.

Front fog lights 1

Refitting

- Access the bulb holder by releasing

To refit, proceed in the reverse order,

flap 2;

taking care not to damage the wiring.

- turn the bulb holder a quarter turn;

Once the bulb has been replaced,

- remove the bulb.

check that it is properly secured.

Type of bulb: H16.

However, we would advise you to

Please note when work-

have these bulbs replaced by an

ing close to the engine that

Approved Dealer.

it may be hot. In addition,

the engine cooling fan may

come on at any moment. The y

warning light in the engine compart-

ment reminds you of this.

The bulbs are under pres-

To comply with local legislation, or

sure and can break when

Risk of injury.

as a precaution, you can obtain an

replaced.

emergency kit containing a set of

Risk of injury.

spare bulbs and fuses from an ap-

proved Dealer.

5.18

CarManuals2.co

BACK AND SIDE LIGHTS: changing bulbs (1/3)

3

2

4

5

2

1

6

3

7

2

Direction indicator lights,

Release the light assembly from out-

4 Brake light

side the vehicle by pulling towards the

Bulb type 4 : P21W.

brake and side lights

rear.

5 Indicator light

Undo bolt 1 to remove the light.

Remove the bulb holder 3 by releasing

Bulb type 5: PY21W.

clips 2.

6 Reversing light

Bulb type 6: P21W.

Refitting

7 Fog light

To refit, proceed in the reverse order,

Bulb type 6: P21W.

taking care not to damage the wiring,

and fasten clips 2 on the bulb holder 3.

5.19

CarManuals2.co

BACK AND SIDE LIGHTS: changing bulbs (2/3)

10

9

8

LED 8 side lights

High-level brake light

Bulb type 10 : P21W.

Consult an approved dealer.

Remove the nut 9 and release the

brake light from its housing.

Refitting

To refit, proceed in the reverse order,

taking care not to damage the wiring.

The bulbs are under pres-

sure and may break when

replaced.

Risk of injury.

5.20

CarManuals2.co

BACK AND SIDE LIGHTS: changing bulbs (3/3)

13

14

11

12

Number plate light

Indicator lights 13

Undo screw 11.

Unclip indicator light 13 (using a flat-

blade screwdriver or similar).

Remove the light cover 12 to access

the bulb.

Turn bulb holder 14 a quarter of a turn

and take out the bulb.

Bulb type: W5W.

Bulb type: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.21

CarManuals2.co

INTERIOR LIGHTS: changing bulbs (1/5)

3

1

5

A

3

2

4

Front ceiling light 1

Refitting

- Unclip the lens 2 (using a tool such

- Clip the lens 2 on to the bulb holder 3;

as a flat screwdriver), positioned

- clip in the interior lights 1 until the unit

at A;

clicks;

- unclip and release the bulb

- ensure that the interior lights are

holder 3 using the tabs 4;

properly positioned and locked into

- remove the bulb concerned.

place.

Type of bulb 5: W5W.

1

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.22

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (2/5)

6

B

B

8

7

B

8

B

9

10

Front map reading lights 6

Refitting

(depending on the vehicle)

- Clip the lens 7 on to the bulb holder 8;

- Unclip the lens 7 (using a tool such

- clip in the reading spots block 6 until

as a flat screwdriver), positioned

the unit clicks;

at B;

- make sure that the reading spots

- unclip and release the bulb

block is correctly positioned and

holder 8 using the tabs 9;

locked into place.

- remove the bulb concerned.

Type of bulb 10: W5W.

6

5.23

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (3/5)

13

11

13

C

14

12

15

Rear reading spot 11

Refitting

(depending on the vehicle)

- Clip the lens

12 on to the bulb

- Unclip the lens 12 (using a tool such

holder 13;

as a flat screwdriver), positioned

- clip in the reading spots block 11 until

at C;

the unit clicks;

- unclip and release the bulb

- make sure that the reading spots

holder 13 using the tabs 14;

block is correctly positioned and

- remove the bulb concerned.

locked into place.

Type of bulb 15: W5W.

11

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.24

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (4/5)

18

16

16

19

17

Glove box light 16

Remove the bulb concerned.

Luggage compartment

(depending on the vehicle)

Bulb type: W5W.

light 18

Unclip light 16 using a flat-blade screw-

Unclip light 18 (using a flat-blade screw-

driver or similar) by pressing on the

driver or similar), by pressing on tab 19

tab 17 to move the light towards the

to move the light towards the inside of

inside of the unit.

the luggage compartment.

Remove the bulb concerned.

Type of bulb: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.25

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (5/5)

20

22

21

Release the lens 20 and access the

LED light 22

bulb 21.

Consult an approved dealer.

Type of bulb 21: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.26

CarManuals2.co

FUSES (1/4)

3

1

Use the fuse allocation label in the

storage compartment to identify the

fuses.

Certain fuses should only be re-

placed by a qualified professional.

2

A

These fuses are not listed on the

label.

Only change the fuses represented

Fuse box

Tweezers 2

on the label.

If any electrical component does not

Remove the fuse using tweezers 3, lo-

work, check the condition of the fuses.

cated at the back of flap 1.

Fuses in the passenger compart-

To remove the fuse from the tweezers,

ment A

slide the fuse to the side.

Check the fuse in question

and replace it, if necessary,

Unlock the handle 2 and pull to open

It is not advisable to use the free fuse

with a fuse of the same

the flap 1.

locations.

rating.

Depending on the vehicle, to identify

If a fuse is fitted where the rating is

the fuses, refer to the fuse allocation

too high, it may cause the electrical

label located at the back of the flap 1

circuit to overheat (risk of fire) in the

and shown on the following pages.

event of an item of equipment using

To comply with current legislation, or

an excessive amount of current.

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

bulbs and fuses.

5.27

CarManuals2.co

FUSES (2/4)

Before carrying out any

action in the engine com-

partment, you must switch

B

off the ignition. ➥ 2.3.

C

Please note when work-

ing close to the engine that

it may be hot. The engine

Fuses in the engine compartment B

cooling fan may also start

and C

at any moment. The 

warning

Some functions are protected by fuses

light in the engine compartment re-

located in the engine compartment in

minds you of this.

units B and C.

However, because of their reduced

Risk of injury.

accessibility, we advise you to have

your fuses replaced by an approved

dealer.

When working in the engine

compartment, ensure that

the windscreen wiper stalk

is in the park position.

Risk of injury.

5.28

CarManuals2.co

RADIO FREQUENCY REMOTE CONTROL: batteries (1/2)

The batteries are available from ap-

proved Dealers, and their service

life approximately two years.

Check that there is no dye on the

battery: risk of an incorrect electri-

cal contact.

2

1

If they need to be replaced,

be sure to use the same

1

or equivalent type of bat-

Replacing the battery

Note: it is not advisable to touch the

tery (consult an Approved

electronic circuit in the key cover when

Dealer).

Open the case at slot 1 using a flat-

replacing the battery.

blade screwdriver or similar, and re-

place the battery 2, observing the type

and polarity shown on the back of the

cover.

Check that the cover is clipped shut.

When replacing:

- Make sure that the batter-

ies are correctly inserted.

Risk of explosion.

- Do not use the remote control if

the cover does not close prop-

erly.

5.31

CarManuals2.co

BATTERY: troubleshooting (2/2)

Starting the vehicle using the

battery from another vehicle

If you have to use the battery from an-

other vehicle to start, obtain suitable

1

4

jump leads (with a large cross section)

4

from an approved dealer or, if you al-

ready have jump leads, ensure that

B

they are in perfect condition.

The two batteries must have an iden-

tical nominal voltage of 12 volts. The

A

battery supplying the current should

have a capacity (amp-hours, Ah) which

1

3

2

is at least the same as that of the dis-

charged battery.

Ensure that there is no risk of contact

Connect positive (+) lead A to (+) termi-

between the two vehicles (risk of short

nal 1 of the discharged battery, then to

circuiting when the positive terminals

(+) terminal 2 of the battery supplying

are connected) and that the discharged

the current.

battery is properly connected. Switch

off your vehicle ignition.

Connect the negative cable (-) B to the

(-) 3 terminal of the battery supplying

Start the engine of the vehicle supply-

the current and then to the (-) 4 termi-

ing the current and run it at an interme-

nal of the discharged battery.

Check that there is no con-

diate engine speed.

Start the engine as normal. As soon as

tact between leads A and B

it starts, disconnect cables A and B in

and that the positive lead A

reverse order (4-3-2-1).

is not touching any metal

parts on the vehicle supplying the

current.

Risk of serious injury and/or

damage to the vehicle.

5.34

CarManuals2.co

WIPER BLADES: replacement (1/2)

C

1

2

3

A

4

5

G

B

F

D

E

Replacing windscreen wiper

-

press the tab 3 and slide the wiper

To refit

blade downwards until the hook 5

blades 2

To refit the wiper blade, proceed in re-

on the wiper arm is released (move-

To replace the wipers, first put them in

verse order of removal. Make sure that

ment D);

the service positionC.

the blade is correctly locked in position.

-

slide the blade (movement E) then

Ignition switched off:

To return the blades to lowered po-

lift it (movement F) to release it.

sition, make sure that the blades are

- set the stalk 1 to position B (fast

folded down onto the windscreen then

wiping speed function): the wiper

set the 1 stalk to position A (off): the

blades will stop in service position C

windscreen wiper blades will fold into

away from the bonnet;

the bonnet when the ignition is switched

- lift the wiper arm 4;

on.

- turn the blade horizontally (move-

ment G);

5.35

CarManuals2.co

WIPER BLADES: replacement (2/2)

To refit

To refit the wiper blade, proceed in re-

verse order of removal. Make sure that

6

the blade is correctly locked in position.

H

7

Before changing the rear

wiper blade, make sure the

stalk is in the stop position

(deactivated).

Risk of injury.

Replacing the rear screen

- In frosty weather, make

wiper blade 7

sure that the wiper blades

are not stuck by ice

(to

-

With the ignition switched off, lift

avoid the risk of the motor

wiper arm 6;

overheating).

-

pivot the blade 7 until some resist-

ance is met;

- Check the condition of the wiper

–

pull the blade to release it (move-

Check the condition of the wiper

blades.

ment H).

blades. You are responsible for their

Replace the wiper blades as soon

service life:

as they begin to lose efficiency

- clean the blades, windscreen and

(approximately once a year).

rear screen regularly with soapy

water;

Whilst changing the blade, take care

- do not use them when the wind-

not to drop the arm onto the window

screen or rear screen are dry;

after it has been removed as this

- free them from the windscreen or

may break the window.

rear screen when they have not

been used for a long time.

5.36

CarManuals2.co

TOWING: breakdown (2/2)

- Use a rigid towing bar.

If a rope or cable is used

(where the law allows this),

the vehicle being towed

must be able to brake.

- A vehicle must not be towed if it is

1

not fit to be driven.

4

2

- Avoid accelerating or braking

suddenly when towing, as this

2

may result in damage being

caused to the vehicle.

- When towing a vehicle, it is ad-

3

visable not to exceed 15 mph

5

(25 km/h).

Only use the front 1 and rear 4towing

Access to towing points

points (never use the driveshafts or any

Unclip cover 3 or 5 by inserting a flat-

other part of the vehicle).

blade screwdriver or similar under the

These towing points may only be used

cover.

for pulling. They must never be used for

Tighten towing hitch 2 fully: as much

lifting the vehicle directly or indirectly.

as possible by hand at first, then finish

tightening it using the wheelbrace.

Only use the towing eye 2 and the

wheelbrace located in the boot ➥ 5.9.

Ensure that the towing eye

Do not leave the tools unse-

is bolted correctly.

cured inside the vehicle as

they may come loose under

Risk of losing the towed

braking.

object.

5.38

CarManuals2.co

Content      ..     3      4      5      6     ..