Content      ..     4      5      6      7     ..

Renault Captur (2023 year). Manual in english - page 6

ACTIVE EMERGENCY BRAKING (3/8)

Detection of pedestrians and

Special features of warnings

cyclists

Depending on the speed, the warning

(depending on the vehicle)

and braking may be activated simulta-

When driving at a speed between ap-

neously.

proximately 4 mph (7 km/h) and 50

mph (80 km/h), if there is a risk of col-

3

lision with a cyclist or a pedestrian, the

system:

- warns you of a risk of collision: the

red 

warning light or, depend-

ing on the vehicle, 3 and the "Brake"

message are displayed on the instru-

ment panel accompanied by a beep.

If the driver presses the brake pedal

and the system still detects a risk of

If active emergency braking has caused

collision, the braking force may be in-

the vehicle to stop, the vehicle is kept

creased if it is not sufficient to pre-

stationary for a short time. Beyond this

vent the collision.

time limit, the vehicle must be held sta-

tionary by the driver keeping their foot

- may trigger braking:

on the brake pedal.

if the driver fails to react following the

alert and collision becomes immi-

Note: if the driver uses the vehicle con-

nent.

trols (steering wheel, pedals, etc.) the

system may delay certain operations or

not activate.

In the event of emergency manoeu-

vre, you can stop braking at any

moment by:

- tapping the accelerator pedal;

or

- turning the steering wheel as a

collision avoidance manoeuvre.

2.84

CarManuals2.co

ACTIVE EMERGENCY BRAKING (4/8)

- press the 6 or 7 control repeatedly to

4

reach the “Active braking” menu and

press the 8 OK switch.

Press the switch 8 OK again to activate

or deactivate the function:

=

function activated

<

function deactivated

Upon deactivation of the system, the

5

6



warning light illuminates or, de-

pending on the vehicle, the



warning light illuminates on the instru-

8

7

ment panel.

Activating or deactivating the

For vehicles not fitted with a

multimedia screen

system

- With the vehicle stopped, press the

For vehicles fitted with a multimedia

switch 5 as many times as required

screen 4

to reach the “Vehicle” tab;

To activate or deactivate the function,

- press the 6 or 7 control repeatedly to

refer to the multimedia instructions.

reach the “Settings” menu. Press the

switch 8 OK;

Select “ON” or “OFF”.

- press the 6 or 7 control repeatedly to

reach the “DRIVING ASSIST” menu.

Press the switch 8 OK;

This system is reactivated each time

the ignition is switched on.

2.85

CarManuals2.co

DETECTION OF ROAD SIGNS (1/4)

Note: make sure the windscreen is not

For vehicles equipped with a navigation

1

obscured (dirt, mud, snow, condensa-

system and if the vehicle is travelling in

tion etc.).

a country where the speed units differ

from those of the vehicle, the system

For vehicles which are equipped with it,

displays the speed limit sign in the unit

the system also uses information from

of the country, alongside the speed limit

the navigation system.

converted to the unit used by the vehi-

Once the speed limiter is activated, you

cle’s instrument panel.

can adjust the speed limiter indication

For countries where the speed limit is

displayed by the system.

reduced during rainy weather on some

If the limit speed is exceeded, the dis-

types of roads, on vehicles equipped

play panel is modified to warn the driver.

with a navigation system, the system

can modify the limited speed after a few

seconds of wiping the windscreen.

Special situations

The system detects speed limit signs

The system does not take into account

on the side of the road and displays the

exceptional speed limit measures, such

speed limit on the instrument panel.

as peak pollution days.

It mainly uses information taken from

the camera 1, attached to the wind-

screen behind the rear view mirror.

2.90

CarManuals2.co

DETECTION OF ROAD SIGNS (2/4)

Vehicles not fitted with a multimedia

2

screen

- With the vehicle stopped, press the

switch 3 as many times as required

to reach the “Vehicle” tab;

- press the 4 or 5 control repeatedly to

reach the “Settings” menu. Press the

switch 6 OK;

- press the 4 or 5 control repeatedly to

reach the “DRIVING ASSIST” menu.

3

4

Press the switch 6 OK;

- press the 4 or 5 control repeatedly

to reach the “Speed alert” menu and

press the 6 OK switch;

6

5

- press the 6 OK switch to activate or

deactivate the function:

Activating/deactivating the

With the function activated, depend-

ing on local regulations, you can acti-

system

=

function activated

vate the “Risk area display” option. The

Vehicles fitted with a multimedia

system will notify you of the distance

<

function deactivated

screen 2

separating you from this zone, and

while you are travelling in the zone.

To activate or deactivate the function,

refer to the multimedia instructions.

Select “ON” or “OFF”.

2.91

CarManuals2.co

DETECTION OF ROAD SIGNS (3/4)

If the speed limit is exceeded, the circle

7

8

around the panel flashes (7 warning

light) along with a sound signal to warn

the driver.

9

10

Operation

Varying the limit speed

If the speed limit notification differs from

Warning lights

the detected speed value, press and

The function displays the following

hold the following switches:

warning lights:

- 9 (RES/+) to increase the notification

7 Speed limit road signs

speed to the detected speed;

8 Additional road signs (start or end

- 10 (SET/-) to reduce the notification

of “No overtaking” zone, slip road

speed to the detected speed.

speed limit, speed in case of a cara-

van, speed limit with length of appli-

cation, etc.)

2.92

CarManuals2.co

SPEED LIMITER (1/4)

Controls

1 Speed limiter On/Off switch.

2 Cruise control On/Off switch.

3 Switch to activate and decrease the

limit speed (SET/-).

4 Switch to activate and increase the

limit speed or to set the stored limit

5

speed (RES/+).

4

1

5 Speed limiter function standby (with

limited speed memory) (0).

3

2

The speed limiter function helps you

stay within the driving speed limit that

you choose, known as the limit speed.

You can link the speed limiter to

the “Road sign detection” function.

➥ 2.90.

2.94

CarManuals2.co

SPEED LIMITER (2/4)

7

7

4

1

3

Driving

Switching on

To store the current speed, press the 4

switch (RES/+) or the 3 switch (SET/- ):

When a limit speed has been set but

Press switch 1. The 7 warning light ap-

the limit speed replaces the dashes

not yet reached, driving is similar to

pears in grey. The “Speed limiter ON”

and, depending on the vehicle, the 7

driving a vehicle without the speed lim-

message appears on the instrument

warning light appears in white.

iter function.

panel accompanied by dashes to indi-

The minimum stored speed is 19 mph

cate that the speed limiter function is in

Once you have reached the stored

(30 km/h).

operation, waiting to store a limit speed.

speed, no effort on the accelera-

tor pedal will allow you to exceed

the programmed speed except in an

emergency (refer to information on

“Exceeding the limit speed”).

2.95

CarManuals2.co

SPEED LIMITER (3/4)

Exceeding the limit speed

Limited speed cannot be maintained

It is possible to exceed the limit speed

When driving down a steep gradient,

at any time. To do this: press the accel-

the system may not maintain the limit

erator pedal firmly and fully (beyond

speed: the limit speed flashes in red

the resistance point).

on the instrument panel and an audi-

While the speed is being exceeded, the

ble signal sounds at regular intervals to

speed limiter flashes red on the instru-

inform you of this situation.

ment panel. Then, release the accelera-

tor pedal: the speed limiter function will

4

return as soon as you reach a speed

lower than the memorised speed.

3

Varying the limit speed

The limit speed may be changed by

pressing repeatedly or holding down:

- switch 4 (RES/+) to increase speed;

- switch 3 (SET/-) to reduce speed.

If the speed limiter is not

available (after several at-

tempts to activate), contact

an approved dealer.

2.96

CarManuals2.co

SPEED LIMITER (4/4)

7

7

5

4

1

3

2

Putting the function on

Switching off the function

standby

The speed limiter function is inter-

The speed limiter function is suspended

rupted:

when you press switch 5 (0). The limit

- when you press the 1 switch. In this

speed is stored and displayed in grey

case, the speed is no longer stored;

on the instrument panel.

- when you press the 2 switch. In this

case the cruise control is selected

Recalling the limit speed

and there is no stored speed.

If a speed has been stored, it can be re-

The warning light 7 disappears from

called by pressing the 4 switch.

the instrument panel to confirm that the

When the speed limiter is set to

function is no longer active.

standby, pressing the

3 switch

re-activates the function without

taking into account the memorised

speed: the speed at which the vehi-

cle is moving is taken into account.

2.97

CarManuals2.co

CRUISE CONTROL (1/5)

Controls

1

Cruise control On/Off switch.

2

Switch to activate and decrease

cruising speed (SET/-).

3

Switch to activate and increase

cruising speed or to recall the mem-

orised cruising speed (RES/+).

4

4

Switch the function to standby (with

3

5

cruising speed saved) (0).

This function is an addi-

5

Speed limiter On/Off switch.

tional driving aid.

It can under no circum-

2

1

stances replace the driver’s

responsibility to respect speed limits

The cruise control function helps you to

or to be vigilant.

maintain your driving speed at a speed

The driver must always be in control

that you choose, called the cruising

of the vehicle.

speed.

Cruise control must not be used

This cruising speed may be set at any

in heavy traffic, on winding or slip-

speed above 19 mph (30 km/h).

pery roads (black ice, aquaplan-

ing, gravel) and during bad weather

(fog, rain, side winds etc.).

There is a risk of accidents.

2.98

CarManuals2.co

CRUISE CONTROL (2/5)

7

7

3

2

1

Switching on

Activating cruise control

Driving

Press switch 1.

While the vehicle is moving a steady

Once a cruising speed is registered

speed above approximately 19 mph

and the cruise control function is active,

The 7 warning light appears in grey.

(30 km/h), press the 2 (SET/-) switch

you may lift your foot off the accelera-

The “Cruise control ON” message ap-

or the 3 (RES/+) switch: the function

tor pedal.

pears on the instrument panel accom-

is activated and the current speed is

panied by dashes to indicate that the

taken into account.

cruise control function is in operation

The cruising speed replaces the

and waiting to memorise a cruising

dashes. Cruise control is confirmed

speed.

when the memorised speed and warn-

ing light appear in green 7.

If you try to activate the function below

19 mph (30 km/h), the message “Invalid

Please note that you must

Speed” will be displayed and the func-

keep your feet close to the

tion will remain inactive.

pedals in order to react in

an emergency.

2.99

CarManuals2.co

CRUISE CONTROL (3/5)

Exceeding the cruising speed

The cruising speed may be exceeded

at any time by depressing the accelera-

tor pedal.

While it is being exceeded, the cruising

speed flashes in red on the instrument

panel. Then, release the accelerator

pedal: after a few seconds, the vehicle

will automatically return to its set cruis-

3

ing speed.

Cruising speed cannot be

maintained

2

When driving down a steep gradient,

the system may be unable to main-

Adjusting the cruising speed

tain the cruising speed: the memorised

speed will flash in red on the instrument

The cruising speed may be changed by

panel and an audible signal sounds at

pressing the following repeatedly:

regular intervals to inform you of this

- the 2 switch (SET/-) to reduce the

situation.

speed;

- the 3 switch (RES/+) to increase the

speed.

Note: press and hold one of the

switches to modify speed by succes-

sive increments.

If the cruise control is no

longer available (after sev-

eral attempts to activate

it), contact an Approved

Dealer.

2.100

CarManuals2.co

CRUISE CONTROL (4/5)

7

7

4

3

2

Putting the function on

Returning to the cruising speed

NB: if the speed previously stored is

much higher than the current speed,

standby

If a speed is stored, it can be recalled,

the vehicle will accelerate more rapidly

once you are sure that the road condi-

The function is set to standby if you:

to reach this threshold.

tions are suitable (traffic, road surface,

- 4 switch (0);

weather conditions, etc.). Press the

When the cruise control is set to

- the brake pedal;

switch 3 (RES/+) if the vehicle speed is

standby, pressing switch 2 (SET/-) re-

above 19 mph (30 km/h).

activates the cruise control function

- the clutch pedal or shifting to neutral

without taking into account the stored

if the vehicle has an automatic gear-

When the speed is stored, cruise con-

speed: it is the speed at which the vehi-

box;

trol activation is confirmed by the dis-

cle is moving that is taken into account.

play in green of the cruising speed and,

- depending on the vehicle, the clutch

depending on the vehicle, the 7 warn-

pedal for a prolonged period or upon

ing light is displayed.

prolonged neutral position.

The cruising speed is stored and dis-

played in grey on the instrument panel.

2.101

CarManuals2.co

CRUISE CONTROL (5/5)

7

7

5

1

Switching off the function

The warning light 7 disappears from

the instrument panel to confirm that the

The cruise control function is inter-

function is no longer active.

rupted:

- when you press the 1 switch. In this

case, the speed is no longer stored;

- when you press the 5 switch. In this

case the speed limiter is selected

and there is no stored speed.

Putting the cruise control

on standby or switching it

off does not cause a rapid

reduction in speed: you

must brake by depressing the brake

pedal.

2.102

CarManuals2.co

ADAPTIVE CRUISE CONTROL (2/14)

1

8

11

9

3

4

10

7

6

5

2

Location of the camera 1

Controls

Make sure the windscreen is not ob-

3 Safe distance settings

scured (by dirt, mud, snow, condensa-

4 Switch the function to standby (with

tion etc.).

cruising speed saved) (0).

5 Adaptive cruise control main stop/

Location of the radar 2

start switch 

Ensure that the radar area is not ob-

structed

(dirt, mud, snow, a badly

6 Cruising speed activation, storage

fitted/attached front number plate), im-

and decrease switch (SET/-).

pacted, modified (including paintwork)

7 Switch to activate and increase cruis-

or hidden by any accessory fitted on the

ing speed or to recall the memorised

The radar and camera

front of the vehicle (on the grille or logo

cruising speed (RES/+).

zones must be kept clean

etc.).

and free of any tampering in

order to ensure the proper

operation of the system.

2.104

CarManuals2.co

ADAPTIVE CRUISE CONTROL (3/14)

Switching on

The cruising speed 11 replaces the

8

dashes and cruise control is confirmed

Press switch 5.

by the appearance of the cruising speed

11

Warning light 

appears in grey,

in green and warning light 

9

and the message “Adaptive Cruise Ctl

If you try to activate the function when

10

ON” appears on the instrument panel,

the vehicle speed is over 105 mph

accompanied by dashes to indicate that

(170 km/h) or below 19 mph (30 km/h)

the cruise control function is activated

for vehicles fitted with a manual gear-

and waiting to store a cruising speed.

box, the message “Invalid Speed” is

This function cannot be activated when:

displayed and the function is not acti-

vated.

- the parking brake is applied;

Once a cruising speed is memorised

- the Park Assist function is already

and the cruise control function is active,

activated ➥ 2.146.

you may lift your foot off the accelera-

The message “Adaptive Cruise Ctl una-

tor pedal.

Displays

vailable” is displayed on the instrument

Special feature on vehicles with

panel.

8

Adaptive cruise control warning

an automatic gearbox: if the vehicle

light.

speed is below approximately 19 mph

9

Vehicle in front.

Activating cruise control

(30 km/h), the cruising speed will auto-

matically be set to 19 mph (30 km/h).

10

Stored safe distance

When the vehicle is stationary (vehicles

The vehicle will accelerate until it

equipped with an automatic gearbox) or

11

Stored cruising speed.

reaches the stored cruising speed.

when the vehicle is moving at a steady

speed (all vehicles), press the 6 (SET/-)

or 7 (RES/+) switch to activate the func-

tion and store the current speed. The

minimum cruising speed is 19 mph (30

km/h).

Important: you should keep

your feet near the pedals at

all times to prepare for any

event.

2.105

CarManuals2.co

ADAPTIVE CRUISE CONTROL (4/14)

Safe distance control

activation

As soon as cruise control is activated,

the default safe distance 10 is displayed

in green on the instrument panel. The

default safe distance corresponds to

approximately two seconds (see follow-

A

ing pages).

B

3

If the system detects a vehicle in your

C

lane, an outline of a vehicle 9 appears

above the distance gauge 10 on the in-

7

D

strument panel.

6

Your vehicle adapts its speed to that

of the vehicle in front and applies the

brakes if necessary (the brake lights

Setting the cruising speed

Adjusting the following

come on) in order to maintain the dis-

tance displayed on the instrument

You can vary the speed by repeatedly

distance

panel.

pressing (for low variation) or pressing

You can vary the safe distance from the

and holding (for high variation) switch 6

vehicle in front at any time by pressing

Note: the size of the 9 outline varies ac-

or 7:

switch 3 repeatedly.

cording to the distance separating you

from the vehicle in front. The larger the

- use the “SET/-” switch 6 to reduce

The horizontal distance gauge on the

outline, the closer the vehicle in front.

the speed;

instrument panel indicates the various

- use the “RES/+” switch 7 to increase

available safe distances:

the speed.

- distance gauge A: long distance

(corresponding to approximately

2.4 seconds);

2.106

CarManuals2.co

ADAPTIVE CRUISE CONTROL (5/14)

Adjusting the safe distance

(cont.)

- distance gauge B: intermediate dis-

11

tance 2 (corresponding to approxi-

mately 2 seconds);

- distance gauge C: intermediate dis-

tance 1 (corresponding to approxi-

11

mately 1.6 seconds);

- distance gauge D: short distance

(corresponding to approximately

1.2 seconds).

The selected distance gauge appears

in green on the instrument panel. The

other gauges remain in grey.

Exceeding the cruising speed

Then, release the accelerator pedal:

Note: the distance must be set accord-

the cruise control and safe distance

ing to the traffic level, local regulation

The cruising speed may be exceeded

control will automatically resume the

and weather conditions.

at any time by applying the accelerator

speed and distance instructions that

pedal.

you had previously selected.

If it is exceeded, the cruising speed 11

appears in red.

Overtaking manoeuvre

The distance gauge flashes if the dis-

If you wish to overtake the vehicle in

tance between your vehicle and the

front, activating the indicator will tem-

vehicle in front is less than the safe

porarily cancel the safe distance con-

distance selected: the Safe Distance

trol and enable an acceleration speed

Control function is no longer active.

sufficient to complete overtaking.

The safe distance is adjusted by de-

fault on the distance gauge B.

2.107

CarManuals2.co

ADAPTIVE CRUISE CONTROL (6/14)

Stop and start

Putting the function on

On vehicles fitted with an automatic

standby

gearbox, if the vehicle in front slows

You can set the function to standby

down, the system adapts its speed to a

when:

complete stop if necessary (in the event

of a traffic jam, etc.). The vehicle stops

- you press switch 4 (0);

a few metres from the vehicle in front.

- you apply the brake pedal while the

The Stop and Start function can put the

vehicle is moving.

engine on standby ➥ 2.12.

The function is deactivated by the

When the vehicle in front sets off again:

system if:

4

- if the stop does not exceed about

7

three seconds, the vehicle sets off

- you set the automatic gearbox to P

automatically without any action by

or N;

the driver;

- you engage the reverse gear;

- if the stop exceeds about three sec-

- you unbuckle the driver’s seatbelt;

onds, you must apply the accelera-

- you open one of the opening ele-

tor pedal or press button 7 (RES/+) in

ments;

- when you press the clutch pedal for a

order for the vehicle to set off again.

– you press the engine start/stop

prolonged period or upon prolonged

The message “Press RES/+ or ac-

button;

neutral position on vehicles equipped

celerate” appears on the instrument

– the slope is too steep;

with a manual gearbox.

panel to confirm.

- the vehicle speed is above 112 mph

In all circumstances, the standby is con-

If the stop exceeds around three min-

(180 km/h);

firmed when the warning lights appear

utes, the electronic parking brake is au-

- certain driving aids and correction

in grey and the message “Adaptive

tomatically applied and the Stop and

devices are triggered (active emer-

Cruise Ctl Disconnected” appears on

Go adaptive cruise control is deacti-

gency braking, ABS, ESC);

the instrument panel.

vated. The 

warning light disap-

pears to confirm that the function is de-

activated.

Putting the adaptive cruise control in standby or switching it off does not

cause a rapid reduction in speed: you must brake by applying the brake

pedal if necessary.

2.108

CarManuals2.co

ADAPTIVE CRUISE CONTROL (7/14)

Exit from standby

Depending on the situation, the system

sounds a beep associated with:

Based on the stored cruising speed

- the orange alert E if the situation re-

If a speed is stored, it can be recalled,

quires the driver’s attention;

E

once you are sure that the road condi-

or

tions are suitable (traffic, road surface,

weather conditions, etc.).

- the red alert F accompanied by the

message “Brake”, if the situation re-

Press switch 7 (RES/+) in the range of

quires the driver’s immediate atten-

confirmed speeds.

tion.

When the stored speed is recalled, acti-

In all situations, react accordingly

vation of the cruise control is confirmed

F

and perform the appropriate ma-

by the illumination of the cruising speed

noeuvres.

in green.

Note: if the stored speed is higher than

the current speed, the vehicle will ac-

“Take control of the vehicle”

celerate to reach that speed.

warnings

Based on the current speed

In some situations (e.g. coming upon

When the cruise control is set to

a much slower vehicle, vehicle in

standby, pressing switch 6 (SET/-) re-

front changing lanes quickly etc.), the

activates the cruise control function

system may not have time to react.

without taking into account the stored

speed: it is the speed at which the vehi-

cle is moving that is taken into account.

2.109

CarManuals2.co

ADAPTIVE CRUISE CONTROL (8/14)

If the radar detection area is obstructed

Operating faults

or the radar signal is disrupted, the

If an “Adaptive cruise control” function

message “Front radar no visibility” is

operating fault is detected, the mes-

displayed on the instrument panel and

sage “Check Adaptive Cruise control”

the “Adaptive cruise control” function

appears on the instrument panel and

is interrupted. The green warning light

the “Adaptive cruise control” function is



disappears to confirm that the

deactivated.

function has been automatically deac-

If an operating fault is detected on one

tivated.

or more components of the system, the

Ensure that the radar area is not ob-

“Adaptive cruise control” function is in-

8

structed

(dirt, mud, snow, a badly

terrupted.

6

fitted/attached front number plate), im-

The

warning light appears on

pacted, modified (including paintwork)

7

the instrument panel along with, de-

or hidden by any accessory fitted on the

pending on the malfunction, one of the

front of the vehicle (on the grille or logo

following messages:

etc.).

Switching off the function

Conditions in certain geographical

- “Front camera to check”;

The “Adaptive cruise control” func-

areas may hinder the function, for ex-

- “Front radar to check”;

tion is deactivated when you press the

ample:

switch 6.

- arid zones, tunnels, long bridges or

- “Camera/Radar to check”;

lightly used roads without road lines,

- “Check vehicle”.

The warning light 

disappears

without signs or trees nearby;

from the instrument panel to confirm

- a military or airport zone.

Consult an approved dealer.

that the function is no longer active.

You must leave such areas in order for

the function to work.

In all cases, if the message is not

Temporary unavailability

erased after the engine is restarted,

The radar is able to detect vehicles

please contact an authorised dealer.

in front of your vehicle. The system

cannot operate correctly if the radar de-

tection area is obscured or if its signal

is disrupted.

2.110

CarManuals2.co

ADAPTIVE CRUISE CONTROL (9/14)

G

H

J

Limitations of system

The system cannot detect:

Detection during cornering

operation

- vehicles arriving at intersections: slip

When entering a corner or bend, the

road (e.g. H) etc;

radar and/or camera may temporarily

Vehicle detection

not be able to detect the vehicle in front

- vehicles driving on the wrong side of

The system detects only vehicles (cars,

(e.g. J).

the road or reversing towards you.

trucks, motorbikes) that are moving in

The system may trigger an accelera-

the same direction as your vehicle.

tion.

A vehicle turning into the same lane

When exiting a bend, the system’s de-

(e.g. G) will be taken into account by

tection of the vehicle in front may be

the system only once it enters the

disrupted or delayed.

camera and radar detection areas.

The system may trigger abrupt or

The system may trigger abrupt or

delayed braking.

delayed braking.

The adaptive cruise control must

only be used on a motorway (or mul-

ti-lane road separated by a barrier).

2.111

CarManuals2.co

ADAPTIVE CRUISE CONTROL (10/14)

K

L

M

Detection of vehicles in adjacent

Vehicles hidden due to variations in

- vehicles transporting long objects

lanes

ground relief

which exceed the line;

The system may detect vehicles driving

The system will not detect vehicles

- the actual length of tall vehicles

on an adjacent lane when:

hidden due to variations in ground relief

(e.g. L) outside the radar detection

or those located outside of the camera

area (construction machine, agricul-

- you drive into a bend (e.g. K);

and radar detection areas when driving

tural equipment towing vehicle, etc.)

- you are driving on a road with narrow

uphill or downhill.

;

lanes;

- vehicles insufficiently centred in the

Vehicles outside the camera and

- the speed of the vehicle on the ad-

lane;

radar detection areas.

jacent lane is slower and if one of

- narrow vehicles which are very close

these vehicles is located too close to

The system will react late or not at all

(e.g. M).

the lane of the other.

if the detected vehicles are outside the

camera and radar detection areas, par-

The system may incorrectly trigger

ticularly in the following cases:

vehicle slowing or braking.

2.112

CarManuals2.co

ADAPTIVE CRUISE CONTROL (11/14)

12

P

13

14

N

Q

Stationary and slow moving

- vehicles in front 12 that change lane,

vehicles

discovering a stationary vehicle 13

(e.g. P);

When your speed is over approximately

31 mph (50 km/h), the system does

- when the vehicle is stationary 14,

not detect:

when you change lane (e.g. Q).

- stationary vehicles (e.g N);

- very slow moving vehicles.

When your speed is less than approxi-

mately 31 mph (50 km/h), the system

may not react or may react very late

Always be ready to take control

to:

of your vehicle when you come

upon stationary or very slow

- stationary vehicles (e.g N);

moving vehicles (e.g. N).

- very slow moving vehicles;

The adaptive cruise control does

not trigger an emergency stop and

its braking capability is limited.

2.113

CarManuals2.co

ADAPTIVE CRUISE CONTROL (12/14)

15

16

R

S

Non-detection of fixed obstacles

Detection of vehicles moving into

and objects of a small size

lane at high speed

The system cannot detect:

If your vehicle is overtaken by another

vehicle driving at high speed 15 (motor-

- pedestrians, bikes, scooters, etc. ;

cycle, car, etc.) and the vehicle is tem-

- animals;

porarily between you and the vehicle

- fixed obstacles (toll barriers, walls,

in front 16, the system may trigger

etc.) (e.g. R).

undue acceleration, slowing or brak-

ing.

These are not taken into account by the

system. They do not trigger any alert or

reaction by the system.

2.114

CarManuals2.co

MOTORWAY AND TRAFFIC ASSISTANT (3/16)

2

1

3

7

4

6

5

2.119

CarManuals2.co

MOTORWAY AND TRAFFIC ASSISTANT (5/16)

21

20

8

13

14

15

9

19

16

18

10

12

17

17

11

2.121

CarManuals2.co

MOTORWAY AND TRAFFIC ASSISTANT (7/16)

Note: if you press button 11 when the

Stop and Go adaptive cruise control is

not activated, the message: “First acti-

15

vate Adapt. cruise ct” appears on the

instrument panel.

11

17

17

Activating the “Lane

Note: you must keep your hands on

the driving wheel when using the “Lane

Centring” function

Once the Stop and Go adaptive

Centring” function. The 

symbol

cruise control is activated

➥ 2.103,

is displayed to confirm that the function

press button 11 to activate the “Lane

is activated.

Centring” function.

The warning light 15 

is displayed

The “Lane centering activated” mes-

in green and the left-hand and right-

sage appears on the instrument panel

hand line indicators 17 are displayed on

accompanied by the 15 

warning

the instrument panel to confirm that the

function is activated and directing your

light and the 

symbol to confirm

vehicle to the centre of the lane.

that the function is activated.

2.123

CarManuals2.co

MOTORWAY AND TRAFFIC ASSISTANT (8/16)

“Lane Centring” function on

Certain actions carried out by the driver

also suspend the “Lane Centring” func-

standby

tion:

The “Lane Centring” function is put on

15

- activating the indicators;

standby automatically when:

- too much force is used when han-

- the Stop and Go adaptive cruise con-

dling the steering wheel.

trol is put on standby ➥ 2.103;

Standby of the function is confirmed by

- the system no longer detects the

lines or only one line is detected in

the 15 

warning light and the left-

your lane;

hand and right-hand line indicators 17

- the lane is too narrow or too wide;

appearing in grey on the instrument

panel.

- the system does not detect any

hands on the steering wheel;

17

17

- the bend is too sharp;

- the vehicle speed is over approxi-

Once the conditions are met, the func-

mately 99 mph (160 km/h);

tion again directs the vehicle to the

- the vehicle speed is below approx-

centre of the lane. The 15 

warn-

imately 37 mph (60 km/h), without

ing light and left-hand and right-hand

any vehicle in front;

line indicators 17 are displayed in green

- the vehicle touches or breaches a

on the instrument panel.

line;

- the system is temporarily disrupted

(for example: camera obscured by

dirt, mud, snow,condensation, etc.).

Important: you should keep

your feet near the pedals

and your hands on the

steering wheel at all times

You can affect the vehicle trajec-

to prepare for any event.

tory at any point by turning the

steering wheel.

2.124

CarManuals2.co

MOTORWAY AND TRAFFIC ASSISTANT (9/16)

Note: in some situations, the “Lane

Centring” function may no longer detect

your hands on the steering wheel and

may sound a signal:

20

- the vehicle is moving along a long

straight lane and the driver’s hands

are immobile on the steering wheel;

- the driver is holding the steering

wheel very lightly;

- ...

If the “Lane Centring” function is de-

activated due to the driver’s hands not

22

being detected on the steering wheel,

the Stop and Go adaptive cruise control

function continues to function.

“Hands on steering wheel”

- after approximately 30 seconds,

the message: Keep hands on steer-

alert

ing wheel appears on the instrument

When the “Lane Centring” function no

panel 22 and the warning light 20

longer detects your hands on the steer-

ing wheel, several warning levels will



appears in red, accompanied

be triggered:

by an audible signal of gradually in-

creasing volume;

- after

15 seconds, the message:

Keep hands on steering wheel is

- after approximately 45 seconds,

shown in yellow on the instrument

the audio sources go on standby,

panel 22;

the audible signal sounds contin-

ually, the warning light 20 

is

In the first two alert levels, when the

switched off and the message “Lane

system again detects the presence

centering deactivated” appears in

of the driver’s hands on the steering

red on the instrument panel 22: the

wheel, the system stops the alerts.

“Lane Centring” function is deac-

The function continues to direct the

tivated.

vehicle to the centre of the lane.

2.125

CarManuals2.co

Content      ..     4      5      6      7     ..