Nissan Qashqai (2007-2010). Manual - part 573

P0705 PARK/NEUTRAL POSITION SWITCH

TM-227

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Diagnosis Procedure

INFOID:0000000000988655

1.

 CHECK HARNESS BETWEEN TCM AND PNP SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and PNP switch connector.

3.

Check continuity between TCM connector terminals and PNP switch connector terminals.

4.

If OK, check harness for short to ground and short to power.

5.

Reinstall any part removed.

Is the inspection result normal?

OK

>> GO TO 2.

NG

>> Repair or replace damaged parts.

2.

 DETECT MALFUNCTIONING ITEM

Check the following items.
• Harness for short or open between ignition switch and PNP switch.
• 10A fuse (No. 55, located in the IPDM E/R).
• Ignition switch.

Is the inspection result normal?

OK 

>> GO TO 3.

NG

>> Repair or replace damaged parts.

3.

 CHECK PNP SWITCH

Check PNP switch. Refer to 

TM-227, "Component Inspection"

.

Is the inspection result normal?

OK 

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

CHECK TCM

Check TCM input/output signals. Refer to 

TM-285, "Reference Value"

.

Is the inspection result normal?

OK

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NG

>> Replace the TCM. Refer to 

TM-325, "Exploded View"

.

Component Inspection

INFOID:0000000000988656

1.

CHECK PNP SWITCH

Change selector lever to various positions to check the continuity between terminals on the PNP switch and
ground.

 TCM connector

 PNP switch connector

Continuity

Connector

Terminal

Connector

Terminal

F25

1

F21

8

Existed

2

3

3

4

4

1

11

2

Selector lever position

PNP switch connector

Continuity

Connector

Terminal

TM-228

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0705 PARK/NEUTRAL POSITION SWITCH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK CVT POSITION

1.

Disconnect control cable.

2.

Check PNP switch. (Refer to step 1 above.)

Is the inspection result normal?

YES

>> Adjust CVT position. Refer to 

TM-324, "Inspection and Adjustment"

.

NO

>> GO TO 3.

3.

CHECK PNP SWITCH

1.

Remove PNP switch from transaxle assembly. Refer to 

TM-337, "Exploded View"

.

2.

Check PNP switch. (Refer to step 1 above.)

Is the inspection result normal?

YES

>> Adjust PNP switch. Refer to 

TM-337, "Inspection and Adjustment"

.

NO

>> Replace PNP switch. Refer to 

TM-337, "Exploded View"

.

P

F21

2

5

 Existed

6

7

R

5

8

N

3

5

6

7

D

4

5

P0710 CVT FLUID TEMPERATURE SENSOR

TM-229

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0710 CVT FLUID TEMPERATURE SENSOR

Description

INFOID:0000000000988657

The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM.

DTC Logic

INFOID:0000000000988658

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “DATA MONITOR”.

3.

Start engine and maintain the following conditions for at least 10 minutes (Total).

With GST

Follow the procedure “With CONSULT-III”.

Is “P0710 ATF TEMP SEN/CIRC” detected?

YES

>> Go to 

TM-229, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000000988659

1.

 CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect the TCM connector.

3.

Check resistance between TCM connector terminals.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

 CHECK CVT FLUID TEMPERATURE SENSOR

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0710

ATF TEMP SEN/CIRC

During running, the CVT fluid 
temperature sensor signal volt-
age is excessively high or low.

• Harness or connectors

(Sensor circuit is open or 
shorted.)

• CVT fluid temperature sensor

VEHICLE SPEED

: 10 km/h (6 MPH) or more

ENG SPEED

: 450 rpm more than

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

TCM connector

Temperature 

°

C (

°

F)

Resistance (Approx.)

Connector

Terminal

F25

13

 25

20 (68)

6.5 k

Ω

80 (176)

0.9 k

Ω

TM-230

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0710 CVT FLUID TEMPERATURE SENSOR

Check CVT fluid temperature sensor. Refer to 

TM-230, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the transaxle assembly. Refer to

TM-351, "2WD : Exploded View"

 (2WD), 

TM-354, "4WD

: Exploded View"

 (4WD).

3.

 CHECK HARNESS BETWEEN TCM AND CVT FLUID TEMPERATURE SENSOR

1.

Disconnect the CVT unit harness connector.

2.

Check continuity between TCM connector terminals and CVT unit harness connector terminals.

3.

If OK, check harness for short to ground and short to power.

4.

Reinstall any part removed.

Is the inspection result normal?

OK

>> GO TO 4.

NG

>> Repair or replace damaged parts.

4.

CHECK TCM

Check TCM input/output signals. Refer to 

TM-285, "Reference Value"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

NO

>> Replace the TCM. Refer to 

TM-325, "Exploded View"

.

Component Inspection

INFOID:0000000000988660

 CVT FLUID TEMPERATURE SENSOR

1.

CHECK CVT FLUID TEMPERATURE SENSOR

1.

Turn ignition switch OFF.

2.

Disconnect CVT unit harness connector.

3.

Check resistance between CVT unit harness connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the transaxle assembly. Refer to 

TM-351, "2WD : Exploded View"

 (2WD), 

TM-354, "4WD

: Exploded View"

 (4WD).

TCM connector

CVT unit harness connector

Continuity

Connector

Terminal

Connector

Terminal

F25

13

F24

17

Existed

25

19

CVT unit harness connector

Temperature 

°

C (

°

F)

Resistance (Approx.)

Connector

Terminal

 F24

 17

 19

 20 (68)

6.5 k

Ω

 80 (176)

0.9 k

Ω