Nissan Qashqai (2007-2010). Manual - part 572

U1010 CONTROL UNIT (CAN)

TM-223

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

U1010 CONTROL UNIT (CAN)

Description

INFOID:0000000000988646

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN-H and CAN-L) allowing a high rate of information transmission with
less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC Logic

INFOID:0000000000988647

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Start engine and wait for at least 6 seconds.

3.

Perform “SELF-DIAG RESULTS”. Refer to 

TM-216, "CONSULT-III Function (TRANSMISSION)"

.

With GST

Follow the procedure “With CONSULT-III”.
Is “U1010 CONTROL UNIT (CAN)” detected?

YES

>> Go to 

TM-223, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000000988648

1.

CHECK CAN COMMUNICATION CIRCUIT

With CONSULT-III

1.

Turn ignition switch ON and start engine.

2.

Select “SELF-DIAG RESULTS”.

Is any malfunction of the “U1010 CONTROL UNIT (CAN)” indicated?

YES

>> Print out CONSULT-III screen, go to LAN section. Refer to 

LAN-46, "Trouble Diagnosis Flow

Chart"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

U1010

CONTROL UNIT (CAN)

When detecting error during the 
initial diagnosis of CAN control-
ler to TCM.

Harness or connectors
(CAN communication line is 
open or shorted.)

TM-224

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0703 STOP LAMP SWITCH

P0703 STOP LAMP SWITCH

Description

INFOID:0000000000988649

ON, OFF status of the stop lamp switch is sent via the CAN communication from the BCM to TCM using the
signal.

DTC Logic

INFOID:0000000000988650

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Start engine.

3.

Start vehicle for at least 3 consecutive seconds.

4.

Perform “SELF-DIAG RESULTS”. Refer to 

TM-216, "CONSULT-III Function (TRANSMISSION)"

.

Is “P0703 BRAKE SW/CIRC” detected?

YES

>> Go to 

TM-224, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000000988651

1.

CHECK STOP LAMP SWITCH

Check stop lamp switch.

Is the inspection result normal?

YES

>>

Check the following. If NG, repair or replace damaged parts.

• Harness for short or open between battery and stop lamp switch.
• Harness for short or open between stop lamp switch and BCM.
• 10A fuse (No. 11, located in fuse block).

NO

>> Repair or replace the stop lamp switch.

Component Inspection

INFOID:0000000000988652

1.

CHECK STOP LAMP SWITCH

Check continuity between stop lamp switch connector terminals.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0703

BRAKE SW/CIRC

When the brake switch does not 
switch to ON or OFF.

• Harness or connectors
- (Stop lamp switch, and BCM 

circuit are open or shorted.)

- (CAN communication line is 

open or shorted.)

• Stop  lamp  switch

Stop lamp switch

Condition

Continuity

Connector

Terminal

E115

1

2

Depressed brake pedal

Existed

Released brake pedal

Not existed

P0703 STOP LAMP SWITCH

TM-225

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Check stop lamp switch after adjusting brake pedal — refer to   

BR-8, "Exploded View"

 (LHD), 

BR-52,

"Exploded View"

(RHD).

Is the inspection result normal?

YES

>>

Check the following. If NG, repair or replace damaged parts.

• Harness for short or open between battery and stop lamp switch.
• Harness for short or open between stop lamp switch and BCM.
• 10A fuse (No. 11, located in fuse block).

NO

>> Repair or replace the stop lamp switch.

TM-226

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0705 PARK/NEUTRAL POSITION SWITCH

P0705 PARK/NEUTRAL POSITION SWITCH

Description

INFOID:0000000000988653

• The PNP switch assembly includes a transaxle range switch.
• The transaxle range switch detects the selector lever position and sends a signal to the TCM.

DTC Logic

INFOID:0000000000988654

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “DATA MONITOR”.

3.

Start engine.

4.

Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

With GST

Follow the procedure “With CONSULT-III”.

Is “P0705 PNP SW/CIRC” detected?

YES

>> Go to 

TM-227, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Item name

Condition

Display value

P POSITION SW

Selector lever in “P” position

ON

Other than the above position.

OFF

R POSITION SW

Selector lever in “R” position

ON

Other than the above position.

OFF

N POSITION SW

Selector lever in “N” position

ON

Other than the above position.

OFF

D POSITION SW

Selector lever in “D” position

ON

Other than the above position.

OFF

RANGE

Selector lever in “N” or “P” position

N/P

Selector lever in “R” position

R

Selector lever in “D” position

D

DTC

Item

 (CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0705

PNP SW/CIRC

TCM does not receive the cor-
rect voltage signal (based on 
the gear position) from the 
switch.

• Harness or connectors

(PNP switches circuit is open 
or shorted.)

• PNP switch

VEHICLE SPEED

: More than 10 km/h (6 MPH)

ENG SPEED

: More than 450 rpm

ACC PEDAL OPEN

: More than 1.0/8