Renault Master (2023 year). Manual in english

TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

Range

b) Journey parameters (continued):

Estimated range with remaining fuel.

541 km

The value is displayed after driving 400 metres.

Distance

Distance travelled since last reset.

522 km

Average

Average speed since the last reset.

The value is displayed after driving 400 metres.

123.4 km/h

55.8 mph (90 km/h)

c) Current speed (depending on the vehicle).

1.99

CarManuals2.co

TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

On-board computer with mileage-

before-service message

Service distance.

With the ignition switched on, the engine not running and

Service Due in

Service Intervals

the display set to “Service Intervals”, press button 1 or 2 for ap-

40 000 km / 24 months

proximately 5 seconds to display the mileage before service

(distance or time to the next service). When the distance value

approaches its limit, there are several possible scenarios:

- range less than 930 miles (1,500 km) or one month: the

Service Due in

message “Service Due” is displayed accompanied by the

300 km / 24 days

nearest term (distance or time);

- range equal to 0 miles (0 km) or date of service reached:

the message “Service Required” is displayed accompanied

The vehicle requires a service as soon as possible.

Service Required

Reset: to reset the distance before the next service, press and hold button 1 or 2 for approximately 10 seconds until the display

shows the mileage before service permanently.

NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the

event of an oil change, both the distance before the next service and the next oil change should be reset.

1.101

CarManuals2.co

TRIP COMPUTER AND WARNING SYSTEM: journey parameters (5/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

On-board computer with distance before

next service message (cntd.)

Mileage before service

With the ignition on, the engine not running and the display

Oil Change in

Service Intervals

showing “Service Intervals”, press button 1 or 2 for about 5 sec-

40 000 km / 24 months

onds to display the mileage before the next service, then press

button 2 to view the mileage before the next oil change (distance

or time remaining before the next service). When the distance

value approaches its limit, there are several possible scenarios:

Service Due in

- range less than 930 miles (1,500 km) or one month: the

300 km / 24 days

message “Service Due” is displayed accompanied by the

nearest term (distance or time);

- range equal to 0 miles (0 km) or date of oil change reached:

the message “Service Required” is displayed accompanied

Service Required

The vehicle requires an oil change as soon as possible.

Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,

door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can

therefore decrease more quickly in some cases than the actual distance travelled.

Reset: to reset the distance before the next service, press and hold button 1 or 2 for approximately 10 seconds until the display

shows the mileage before oil change permanently.

NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the

event of an oil change, both the distance before the next service and the next oil change should be reset.

1.102

CarManuals2.co

TRIP COMPUTER AND WARNING SYSTEM: journey parameters (6/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

Interpreting the display selected

Tyre pressure

g) Tyre pressure reset ➥ 2.36.

init. long press

h) General settings.

Settings (Press

Press button 1 or 2for approximately 5 seconds

and hold)

to select the display language.

i) Trip log.

Successive display:

Vehicle Systems OK

- information messages (ESC deactivated/ac-

tivated, STOP and START activated etc.);

- operating fault messages (check the injection

system, airbag etc.).

j) Estimated range with remaining reagent

Top Up AdBlue

➥ 1.123.

before 2400 km

1.103

CarManuals2.co

TRIP COMPUTER: information messages

These can help in the vehicle starting phase, or give information about a selection or a driving status.

Examples of information messages are given in the following pages.

Examples of messages

Interpretation of messages

Traction control Off

Indicates that you have deactivated the traction control function.

Steering Wheel Not Locked

Indicates that the steering column has not been locked.

Parking Brake ON

Indicates that the parking brake has been applied.

1.104

CarManuals2.co

TRIP COMPUTER: operating fault messages

as possible. If you fail to follow this recommendation, you risk damaging your vehicle.

warning light stays on. Examples of operating fault messages are given on the following pages.

Examples of messages

Interpretation of messages

Indicates a fault in the traction control system or in the electronic stability

WARNING: Check ESC

program ➥ 2.24.

Indicates that there is water present in the diesel fuel.

Clean Diesel Filter

Contact an approved Dealer as soon as possible.

Indicates that a fault has occurred in the gearbox; contact an approved

WARNING: Check Gearbox

Dealer as soon as possible.

Indicates a fault in the automatic lights operation. Consult an approved

WARNING: Check Lighting

dealer.

- Indicates a fault in the vehicle’s emission control system.

Check Anti- Pollution System

- Indicates a fault in the exhaust gas reduction system when it is accompa-

nied by the 

warning light. ➥ 1.123.

1.105

CarManuals2.co

TRIP COMPUTER: warning messages

These appear with the® warning light and require you to stop immediately, for your own safety, as soon as traffic

conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.

Some examples of warning messages are given below. Note: the messages appear on the display either individually or alternately

(when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.

Examples of messages

Interpretation of messages

WARNING: Power Steering

Indicates a fault in the steering system.

Indicates an injection fault, the vehicle’s engine has overheated or

WARNING: Engine Failure Risk

there is a serious engine fault.

WARNING: Electric System

Indicates a fault in the vehicle battery charging circuit (alternator, etc.).

WARNING: Gearbox Overheating

Indicates that the gearbox is overheating.

Puncture

Indicates that at least one wheel is punctured or severely underinflated.

1.106

CarManuals2.co

CLOCK AND EXTERIOR TEMPERATURE (1/2)

12:00

Display A

Display B

To access the clock setting display,

Vehicles fitted with a multimedia

press 1 or 2 as many times as neces-

touch-screen, navigation aid sys-

sary until 3 is displayed.

tems, telephones, etc.

Press and hold button 1 or 2 until the

Refer to the separate instructions for

hours flash. You are now in setting

the function to understand the special

mode, press and hold the 1 or 2 button

features of this equipment.

to set the hour.

Wait a few seconds, the minutes flash:

repeatedly press the 1 or 2 button to set

If the power supply is cut (battery

them.

disconnected, supply wire cut, etc.),

the clock must be reset.

When setting is complete, wait a few

seconds before changing the display.

For safety reasons, carry out any

adjustments when the vehicle is not

being driven.

1.107

CarManuals2.co

SCREEN WASHER, WIPER (1/3)

Vehicle fitted with intermittent

Special note

windscreen wipers

When driving the vehicle, the wiping

speed slows down whenever the ve-

A park

hicle stops. For example, fast wiping

B intermittent wiping

speed will slow to normal wiping speed.

The wipers will pause for several

As soon as the vehicle moves off,

seconds between sweeps. It is pos-

wiping will return to the speed originally

sible to change the time between

selected.

sweeps by turning ring 2.

If stalk 1 is operated, it overrides and

C normal wiping speed

cancels the automatic function.

D fast wiping speed

Note: in the event of mechanical sei-

zure, the system automatically cuts the

power supply to the wipers.

1.109

CarManuals2.co

SCREEN WASHER, WIPER (2/3)

Note:

the rain sensor is only intended as a

driving aid. In the event of reduced

visibility, the driver should manually

activate the wipers. In foggy weather

or during snowfalls, wiping is not au-

tomatically triggered and remains

under the driver’s control;

in the event of temperatures below

zero, automatic wiping is not acti-

vated when the vehicle is started. It

is automatically activated as soon as

the vehicle exceeds a certain speed

(approximately 5 mph (8 km/h));

do not activate automatic wiping in

Vehicle fitted with windscreen

C normal wiping speed

dry weather;

wiper rain sensor

D fast continuous wiping.

fully de-ice the windscreen before

A park

activating automatic wiping;

B automatic wiper function.

when washing the vehicle under a

When this position is selected, the

roller type car wash, return the ring 1

system detects water on the wind-

to the A position to deactivate auto-

screen and triggers the wipers at a

matic wiping.

suitable wiping speed. It is possi-

ble to change the triggering thresh-

old and the time sweeps by turning

ring 2:

- E: minimum sensitivity;

- F: maximum sensitivity.

1.110

CarManuals2.co

SCREEN WASHER, WIPER (3/3)

Efficiency of a wiper blade

Check the condition of the wiper

blades. How long they last depends

on you:

- it must remain clean: clean the

blade and the screen regularly

with soapy water;

- do not use it when the screen is

dry;

Windscreen washer

- free it from the screen when it has

not been used for a long time.

With the ignition on, pull stalk 1 then

When working in the engine

release.

In all cases, replace it as soon as

compartment, ensure that

it begins to lose efficiency: approxi-

the windscreen wiper stalk

A brief pull will trigger a single sweep

mately once a year. ➥ 5.39.

is in position A (park).

of the wipers, in addition to the wind-

screen washer.

Risk of injury.

Precautions for using the

A longer pull will trigger three sweeps

of the wipers followed, a few seconds

wipers

later, by a fourth, in addition to the wind-

- In freezing or snowy weather,

screen washer.

Before any action involving

clear the screen before starting

the windscreen

(washing

the wipers (risk of motor over-

the vehicle, de-icing, clean-

heating);

ing the windscreen, etc.)

- ensure that no objects are ob-

return stalk 1 to position A (stop).

structing the travel of the blade.

Risk of injury and/or damage.

1.111

CarManuals2.co

EXTERIOR LIGHTING AND SIGNALS (1/5)

Dipped beam

headlights

Manual operation

Turn ring 3 until the symbol is opposite

mark 2. This indicator light on the in-

strument panel comes on.

Automatic operation

(depending on vehicle)

Turn ring 3 until the AUTO symbol is op-

posite mark 2: with the engine running,

the dipped beam headlights switch on

or off automatically depending on the

Daytime running lights

brightness of the light outside, without

Side lights

any action on stalk 1.

function

Turn ring 3 until the symbol is opposite

The daytime running lights come on

mark 2.

automatically with no action on stalk 1

This indicator light on the instrument

when the engine is started, and they go

panel comes on.

off once the engine is switched off.

Before driving at night,

check that the electrical

Side position lights

equipment is operating cor-

(depending on the vehicle)

rectly and adjust the head-

light beams (if your vehicle is not

These draw other road users’ attention

carrying its normal load). ➥ 1.117.

to the width of the vehicle.

As a general precaution, check that

They come on when the side lights are

the lights are not obscured (by dirt,

switched on.

mud, snow or objects being trans-

ported).

1.112

CarManuals2.co

EXTERIOR LIGHTING AND SIGNALS (2/5)

To switch off the lights before they go

out automatically, turn ring 3 to any po-

sition, then return it to position AUTO.

“See-me-home lighting”

function

This function allows you to briefly switch

on the dipped beam headlights (to pro-

vide light when opening a gate, etc.).

With the engine and lights switched

If the vehicle is parked

off, and the ring 3 in position AUTO,

on the hard shoulder with

pull the stalk 1 towards you: the dipped

the tailgate open, the rear

beam headlights come on for approxi-

lights may be obscured.

mately one minute. To increase this du-

You should make other road users

ration, you may pull the stalk up to four

aware of your vehicle by using a

times (total time restricted to approxi-

warning triangle or other equipment

mately four minutes).

specified by the road traffic regula-

tions of the country you are driving

in.

1.113

CarManuals2.co

EXTERIOR LIGHTING AND SIGNALS (3/5)

Automatic main beam



headlights

Depending on the vehicle, this system

The system may encounter difficul-

switches the main beam headlights on

ties under certain conditions, inclu-

and off automatically. The function uses

ding:

a camera located behind the interior

extreme weather conditions (rain,

rear-view mirror to detect vehicles that

snow, fog, etc.);

are following and coming in the oppo-

obstruction in front of the wind-

site direction.

screen or camera;

The main beam headlights come on au-

when a following or oncoming ve-

tomatically if:

hicle has weak or hidden lighting;

- exterior light is weak;

incorrect settings for the front

- no other vehicles or lighting are de-

headlights;

tected;

reflective systems;

- the vehicle speed is above approxi-

–

mately 30 mph (45 km/h).

If any of the above conditions are not

Main beam headlights

fulfilled, the system switches to dipped

With the dipped beam headlights lit,

beam headlights.

pull the stalk 1. This indicator light on

the instrument panel comes on.

Note: make sure the windscreen is not

obscured (dirt, mud, snow, condensa-

To return to the dipped headlight posi-

tion etc.).

tion, pull stalk 1 towards you again.

Using the portable naviga-

tion system at night in the

windscreen area below the

camera may disturb the op-

eration of the “automatic main beam

headlights” system (risk of reflection

on the windscreen).

1.114

CarManuals2.co

EXTERIOR LIGHTING AND SIGNALS (4/5)

Automatic main beam

Operating faults



headlights (continued)

When the message “WARNING: Check

Lighting” with warning light

Activation/Deactivation

is displayed and warning light k

To activate automatic main beam

flashes on the instrument panel, this in-

headlights:

dicates that there is a lighting fault.

- turn ring 3 until the AUTO symbol is

Consult an approved dealer.

opposite mark 2;

- pull stalk 1 towards you.

Warning light 

comes on the in-

strument panel.

To deactivate automatic main beam

headlights:

- pull stalk 1 towards you again;

- or turn ring 3 to a position other than

AUTO.

Warning light 

goes out on the in-

strument panel.

The “automatic main beam

headlights” system should

under no circumstances be

used to replace driver atten-

tion and responsibility with regard

to vehicle lighting and adapting to

light, visibility and traffic conditions.

Each time you start the engine, pull

the stalk 1 towards you to reactivate

the system.

1.115

CarManuals2.co

EXTERIOR LIGHTING AND SIGNALS (5/5)

Rear fog lights

Switching off the lights



Turn the centre ring 4 of the

The lights will go out automatically

stalk 1 until the symbol is opposite the 5

when the engine is switched off, the

mark.

driver’s door is opened or the vehicle

is locked. In this case, the next time

The rear fog lights only work if the ex-

the engine is started the lights will be

terior lights have been activated. An in-

switched back on according to the posi-

dicator light on the instrument panel will

tion of the ring 3.

come on.

Do not forget to switch off the fog lights

when they are no longer needed, to

Lights-on warning buzzer

avoid inconveniencing other road

If the lights are on after the engine is

users.

switched off, a warning beep sounds

When the exterior vehicle lights are

when the driver’s door is opened to

switched off, the rear fog lights switch

warn you that the lights are still on (to

off or the equipment returns to the front

avoid battery discharge).

Front fog lights

fog lights position (if they are fitted).

Turn the centre ring 4 of the

stalk 1 until the symbol is opposite the 5

mark.

The front fog lights only work if the ex-

terior lights have been activated. An in-

dicator light on the instrument panel will

come on.

1.116

CarManuals2.co

HEADLIGHT BEAM ADJUSTMENT (1/2)

Load status

Control position

Driver only

Driver with two passengers and

luggage compartment loaded (1)

Driver only with the luggage

compartment loaded (1)

The table below gives some examples. In all cases, adjust control A according to

the vehicle load so that the road can be seen and other drivers are not dazzled.

On vehicles fitted with this function,

control A allows you to adjust the height

of the beams according to the load.

Turn control A downwards to lower the

headlights and upwards to raise them.

(1) Load status at maximum permitted weight.

1.117

CarManuals2.co

HEADLIGHT BEAM ADJUSTMENT (2/2)

When driving on the left in a left-hand

drive vehicle (or vice versa), you must

adjust your lights temporarily for the

duration of your trip.

Temporary adjustment

Open the bonnet and identify the mark-

ing B next to one of the front headlight

projectors.

For each headlight, using a screw-

driver, turn the screw 1 by a quarter

turn towards the - symbol to lower the

beams.

Return to the starting point once your

trip is over: turn the screw 1 by a quar-

ter turn towards the + symbol to raise

the beams.

1.118

CarManuals2.co

AUDIBLE AND VISUAL SIGNALS

Direction indicators

Horn

Hazard warning lights

Move the stalk 1 in the same direc-

Press on the sides 2 of the steering

Press the switch 3. This switch

tion as you want to move the steering

wheel boss.

activates all four direction indicators

wheel.

and the side indicator lights simultane-

ously. It must only be used in an emer-

One-touch mode

Headlight flasher

gency to warn drivers of other vehicles

Briefly shift the stalk

1 upwards or

Pull stalk 1 towards you then release it

that you have had to stop in an area

downwards, not exceeding the point

to flash the headlights.

where stopping is prohibited or unex-

of resistance, then release it: the stalk

pected, or that you are obliged to drive

will return to its original position and the

under special conditions.

direction indicator light concerned will

In the event of emergency braking or

flash three times.

sudden deceleration, the flashing lights

are activated at a faster frequency.

They are switched off automatically

once the emergency braking or decel-

eration is complete.

1.119

CarManuals2.co

FUEL TANK (1/3)

Useable capacity of the tank: ap-

Fuel grade

proximately

23.1 gal or

17.6 gal

It is essential to use diesel. Make sure

(105 litres or 80 litres) (depending on

that no water enters the fuel tank ac-

the vehicle).

cidentally during filling. The sealing

system and its surrounding area must

Filling the tank

be dust-free.

Please observe the following instruc-

Use a high-grade fuel that complies

tions:

with the specific or equivalent legisla-

tion in force in the country where the

- with the ignition off, wait at least

vehicle is marketed. It must comply with

20 seconds before starting to fill

the indications on the label located on

with fuel;

the cover 1 ➥ 6.6.

- open the driver’s door in order to

open the flap 1;

- depending on the vehicle, unlock the

cap 2 using the key, then remove it

Filling with fuel

and attach it to the flap 1;

When the pump cuts out automatically

- when filling the tank partially, add at

at the end of the filling procedure, a

least 2.2 gallons (10 litres) of fuel.

maximum of two further filling attempts

may be made to maintain an expansion

If these instructions are not observed,

volume.

the tank filling level will not be taken

into account on the instrument panel.

To fill up with fuel, the

engine must be stopped

(and not only on standby

in the case of vehicles

equipped with the Stop and Start

function): you must switch off the ig-

Fuel types that conform to European

nition ➥ 2.3, ➥ 2.4.

standards which the engines of ve-

hicles sold in Europe are compatible

Fire hazard.

After filling, check that the cap and

with. ➥ 6.6.

cover are closed.

1.120

CarManuals2.co

FUEL TANK (2/3)

Fuel filler cap: this is a

Persistent smell of

specific type.

fuel

If you have to replace it,

If you notice a persistent

make sure it is identical

fuel odour you should:

to the original cap. Contact an ap-

proved Dealer.

stop the vehicle when traffic con-

ditions allow it and switch off the

Never place the cap near a source

ignition;

of heat or flame.

switch on the hazard warning

Do not wash the filler area with a

lights and ask your passengers to

high-pressure washer.

leave the vehicle and stay clear

of the traffic;

Do not mix even small

contact an authorised dealer.

amounts of petrol

(un-

leaded or E85) with diesel.

Do not use ethanol-based

fuel if your vehicle is not compatible

with this fuel.

No modifications what-

Do not add reagent to the fuel -

soever are permitted on

Please note when work-

otherwise you risk damaging the

any part of the fuel supply

ing close to the engine that

engine ➥ 1.123.

system (computers, wiring,

it may be hot. In addition,

fuel circuit, injector, protection

If you wish to add an additive to the

the engine cooling fan may

covers, etc.) as this may be danger-

fuel, use a product approved by our

ous (such work must be undertaken

start at any moment. The 

Technical Department.

by qualified Network personnel).

warning light in the engine compart-

Consult an approved dealer.

ment reminds you of this.

Risk of injury.

1.121

CarManuals2.co

FUEL TANK (3/3)

Repriming the fuel circuit

After a breakdown caused by com-

pletely running out of fuel, the system

must be reprimed before the engine is

restarted:

- set the ignition key to the “On” posi-

tion M ➥ 2.2 and wait a few minutes

before starting to enable the fuel cir-

cuit to be primed;

- turn the key to position D. If the

engine does not start, repeat the pro-

cedure;

- if the engine does not start after sev-

eral attempts, please contact an au-

thorised dealer.

The peripheral components

(al-

ternator, starter, engine mount-

ings etc.) should be protected from

diesel splashes.

1.122

CarManuals2.co

REAGENT TANK (1/8)

Please ensure that you comply with the

legislation of your country.

It is important to remember that failure

to respect regulations in force could

lead to legal action being taken against

the vehicle owner.

To fill up with reagent, the engine

must be stopped (not just on standby

Operating principle

in the case of vehicles with the Stop

and Start function). You must switch

The reagent is intended for Diesel en-

off the ignition ➥ 2.3, ➥ 2.4.

gines fitted with the SCR (selective cat-

alytic reduction) system.

Using the reagent reduces the quantity

If the “xxxKM failure Top up

of nitrogen oxides in exhaust gases.

AdBlue” message appears,

Reagent consumption in real time de-

fill the reagent tank and

pends on vehicle usage conditions, the

Topping up

refer to the filling instruc-

equipment fitted, and driving style.

Useful capacity of fuel tank: approx-

tions.

imately 21 litres or 28 litres (depend-

Risk of immobilisation of the ve-

ing on the vehicle).

Reagent quality

hicle.

Ignition off, open the front passenger

Use only reagents which conform

door to open the cover 2. Unscrew the

to standard ISO 22241 and in accord-

cap 1.

ance with the mark on the tank filler

Filler cap: this is specific.

cap.

Note: ammonium hydroxide vapour

If you have to replace it,

may escape from the cap opening

make sure it is identical to

when the tank temperature is high.

the original cap. Contact

an approved Dealer. Do not wash

the filler area with a high pressure

washer.

1.123

CarManuals2.co

REAGENT TANK (2/8)

Precautions for use

In extreme cold weather conditions

The tank can be filled at the pump. In

In frosty conditions, fill the reagent

other cases, it is essential to read the

tank as soon as the 

warning

information shown on the reagent con-

light and the “TOP UP AdBlue before

tainer (e.g. the can or bottle).

1500 km” message, or, depending on

When filling, handle the reagent care-

After filling the reagent tank, check

the vehicle, the “TOP UP AdBlue before

fully. They can damage clothes,

that the cap and cover are closed,

1200 km” message is displayed on the

shoes, bodywork components etc.

start the engine and WAIT 10 sec-

instrument panel.

onds with the vehicle stationary,

If the reagent overflows, or contami-

Special cases

engine running, before setting off

nates any paintwork, clean the affected

The reagent fluid freezes below about

again.

area quickly with plenty of cold water

-10°C.

If this operation is not carried out,

and a soft cloth.

In these conditions, do not attempt fill-

the filling of the tank will not be

Note: if the reagent crystallises, use a

ing when the fluid is frozen. In the event

taken into account automatically

soft sponge.

of needing to top up or fill the tank

until after several dozens of minutes

of driving.

with reagent (

on), park the ve-

The message “--- TOP UP AdBlue”

hicle in a hotter location if possible so

and/or the warning lights will con-

that the reagent becomes liquid again.

tinue to appear until the filling has

Otherwise, have a qualified profes-

been registered by the system.

sional top up or fill up with reagent fluid.

No work whatsoever is

permitted on any part of

The reagent must not come

the system. To prevent

into contact with eyes or

damage, only qualified per-

skin. If it does, wash the af-

sonnel from our network may work

fected area with plenty of

on the system.

cold water. If necessary, consult a

doctor.

1.124

CarManuals2.co

REAGENT TANK (4/8)

Maintenance/Range

The information displayed on the instrument panel may be accompanied by a beep.

Indicator lights

Messages

What to do?

AdBlue Level Correct (depending on the ve-

hicle)

If the message is displayed when the ignition is switched on,

you have less than 1,491 miles (2,400 km) range remain-

“Top Up AdBlue before 2400 km”

ing.

Refill, or have an approved dealer refill the reagent in the

tank.

If the message is displayed when the ignition is switched on,

you have between 932 miles (1,500 km) and 621 miles

“TOP UP AdBlue before 1500 km” or, de-

(1,000 km) range left or, depending on the vehicle, between



comes

pending on the vehicle, “TOP UP AdBlue

745 miles (1,200 km) and 497 miles (800 km) range left.

on.

before 1200 km”

Refill, or have an approved dealer refill the reagent in the

tank.

1.126

CarManuals2.co

REAGENT TANK (5/8)

Maintenance/Range

The information displayed on the instrument panel may be accompanied by a beep.

Indicator lights

Messages

What to do?

The message is displayed when the ignition is switched on

and is repeated:

- approximately every 62 miles (100 km), you have between

621 miles (1,000 km) and 124 miles (200 km) range left

or, depending on the vehicle, between 497 miles (800 km)



comes

“xxxKM failure Top up AdBlue”

and 124 miles (200 km) range left;

on.

- Approximately every 31 miles (50 km), you have less than

124 miles (200 km) range.

In any event, you or an Approved Dealer should fill the rea-

gent tank as soon as possible.



flashes or

The engine will not start.

comes on, de-

“0KM failure Top up AdBlue”

To restart, you must fill the reagent tank yourself.

pending on the

vehicle.

1.127

CarManuals2.co

REAGENT TANK (6/8)

System faults

When the indicator lights described light up, this may be accompanied by a beep.

Indicator lights

Message

Readings

“Check Anti- Pollution System”

Indicates a fault in the system. Contact your approved dealer as



and

“AdBlue quality to check”

soon as possible.

come on.

“AdBlue injection to check”

This indicates a system fault and that you have less than

621 miles (1,000 km) range left or, depending on the vehicle,

less than 497 miles (800 km) range left before it is no longer

possible to restart the vehicle.

These warnings are repeated:

- every 62 miles (100 km) until you have between approxi-



and

“xxxKM failure antipollution”

mately 621 miles (1,000 km) and 124 miles (200 km)

come on.

range left or, depending on the vehicle, between 497 miles

(800 km) and 124 miles (200 km) left before it is no longer

possible to restart the vehicle;

- Every 31 miles (50 km) when there is less than 124 miles

(200 km) left before the vehicle cannot be restarted.

Contact your approved dealer as soon as possible.

Indicates that after the ignition is switched off the vehicle will not



and

“0KM failure antipollution”

restart. Call an approved Dealer.

come on.

1.128

CarManuals2.co

REAGENT TANK (7/8)

Maintenance/Range

Gauge level

Warnings

What to do?

Range A

Range B



comes on.

You or an Approved Dealer should



flashes for a few

fill or top up the reagent tank.

seconds at the start of the

Range C

warning and each time the

ignition is switched on,

then stays on.

Alert with no message on the

instrument panel



flashes for a few

Loss of engine power.

seconds at the start of the

Bus and rear-wheel drive versions

You or an Approved Dealer

Range D

warning and each time the

The warning light is displayed accord-

should fill the reagent tank as

ignition is switched on,

ing to the reagent level indicated by the

soon as possible.

then stays on. It is accom-

gauge 4 on the instrument panel.

panied by beeps.

In this case, at the next engine

Empty tank.

stop/start, the vehicle speed

is limited to approximately

At E



flashes accompa-

12 mph (20 km/h) until you fill the

nied by beeps.

reagent tank or have it done by an

Approved Dealer.

1.129

CarManuals2.co

REAGENT TANK (8/8)

System faults

When the indicator lights described light up, this may be accompanied by a beep.

Indicator lights

Message

Readings

Indicates a fault in the system. Contact your approved Dealer as



and

“Check Anti- Pollution System”

soon as possible.

come on.



and

Indicates a system fault with a loss of engine power. Contact

flash

when the

your approved dealer as soon as possible.

engine is started

then stay lit.

Indicates a fault in the system. In this case, at the next engine

stop/start, the vehicle speed is limited to approximately 12



flashes and

mph (20 km/h). Contact your approved dealer as soon as pos-

comes on.

sible.

1.130

CarManuals2.co

Section 2: Driving

(advice on use relating to fuel economy and the environment)

Running in, ignition switch

2.2

Starting, stopping the engine

2.3

Stop and Start function

2.4

Special features of Diesel versions

2.7

Driving advice, Eco-driving

2.12

Maintenance and antipollution advice

2.17

Environment

2.18

Gearstick

2.19

Handbrake

2.20

Rear camera

2.21

Driver correction devices and aids

2.24

Active emergency braking

2.30

Tyre pressure loss warning

2.36

Lane departure warning

2.39

Blind spot warning

2.43

Speed limiter

2.49

Cruise control

2.52

Overspeed function

2.56

Parking distance control

2.57

Reversing camera

2.63

Power take-off

2.66

Fast idle speed

2.67

Self-locking differential

2.68

Sequential gearbox

2.69

Emergency call

2.74

2.1

CarManuals2.co

RUNNING IN, IGNITION SWITCH

Up to 930 miles (1,500 km), do not

“Start” position D

exceed 2,500 rpm or approximately

If the engine fails to start at the first at-

56 mph (90 km/h) in the highest gear.

tempt, turn the key back before activat-

After completing this mileage you may

ing the starter again. Release the key

drive faster, however, it is only after ap-

as soon as the engine starts.

proximately 3720 miles (6,000 km) that

Note: several seconds may pass be-

you may reasonably expect full perfor-

tween turning the key and the engine

mance.

starting to allow for engine preheating.

During the running in period, do not ac-

Special note on vehicles with a se-

celerate hard while the engine is still

quential gearbox

cold and do not let the engine over-rev.

Depress the brake pedal with the lever

Service intervals: refer to the

in the N position.

Maintenance Service Booklet for the

Note: if a gear other than neutral is dis-

vehicle.

played, it flashes; starting is not pos-

Note: for a new vehicle in the running-in

sible unless you depress the brake

phase: the coolant level may be higher

Ignition switch

pedal, while holding the key in the start-

than the “MAXI” mark on the tank, then

ing position.

drop to between the “MINI” and “MAXI”

“Stop and steering lock” position St

marks. This does not present a risk.

To lock: remove the key and turn the

steering wheel until the steering column

locks.

To unlock: turn the key and the steering

wheel slightly.

“Accessories” position A

When the ignition is switched off, any

accessories (radio, etc.) will continue to

function.

In the “Accessories” or “On” posi-

tion, a system may automatically

“Ignition on” position M

switch off your vehicle’s accessories

With the ignition on, the engine will be

depending on the battery charge, to

preheating.

prevent it from discharging com-

pletely.

2.2

CarManuals2.co

STOPPING, STARTING THE ENGINE

Depending on the vehicle, if a gear is

Stopping the engine

engaged, the message “Press Clutch

With the engine idling, turn the key to

+ Start” is displayed on the instrument

the “Stop” position St.

panel. Press the clutch pedal.

Turn the key to starter position D with-

out depressing the accelerator

pedal.

Release the key as soon as the engine

Driver’s responsibility

starts.

when parking or stopping

the vehicle

Never leave an animal,

child or adult who is not self-suffi-

cient alone in your vehicle, even for

a short time.

Starting the engine

Starting the vehicle

They may pose a risk to themselves

or to others by starting the engine,

For front-wheel drive and rear-

Turn the ignition key to the “Ignition on”

activating equipment such as the

wheel drive dual wheel versions on

position M and hold this position until

electric windows or locking the

level ground, with the vehicle un-

the engine preheating warning light

doors, for example.

loaded, we recommend starting in

goes out.

second gear.

Also, in hot and/or sunny weather,

please remember that the tempera-

ture inside the passenger compart-

ment increases very quickly.

Never switch off the igni-

RISK OF DEATH OR SERIOUS

tion before the vehicle has

INJURY.

stopped completely. Once

the engine has stopped, the

brake servo, power-assisted steer-

Never start your vehicle

ing, etc., and the passive safety de-

while freewheeling on a

vices such as the airbag and preten-

gradient. Risk of non-acti-

sioners will no longer operate.

vation of power-assisted

steering.

There is a risk of accidents.

2.3

CarManuals2.co

FUNCTION STOP AND START (1/3)

This system enables a reduced fuel

For vehicles equipped with manual

consumption and lower greenhouse

gearboxes:

gas emissions.

- the gearbox is in neutral;

The system is activated automatically

and

when the vehicle is started.

- the clutch pedal is released.

While driving, the system stops the

engine (standby) when the vehicle is

If warning light 

flashes, this

at a standstill (traffic jam, traffic lights,

means that the clutch pedal is not

etc).

sufficiently released.

To fill up with fuel, the engine must

and

be stopped (and not put in standby):

- the vehicle speed is less than ap-

the ignition must be switched off

Conditions for engine

proximately 2 mph (3 km/h).

➥ 2.3, ➥ 1.120.

standby

The engine will restart when you press

Fire hazard.

The vehicle has set off from where it

the clutch pedal and move into gear.

was parked;

For all vehicles:

For vehicles equipped with auto-

If you get out of the vehicle, a beep

matic gearboxes:

Warning light



on the instru-

notifies you that the engine is on

– the gearbox is in position D, Mor N;

ment panel is lit when the engine is on

standby and has not been switched

and

standby.

off.

– the brake pedal is depressed (suffi-

The vehicle equipment remain opera-

ciently hard);

tional while the engine is stopped.

and

Keep your vehicle station-

– the accelerator pedal is not de-

ary when the engine is

pressed;

on standby (shown by the

and

– the speed is zero for around

warning light 

on the

1 second.

instrument panel).

The engine remains in standby if N is

engaged with the parking brake applied

and the brake pedal released.

If the engine stalls while the system

The engine MUST be

is in operation, pressing the clutch

stopped (not put in standby)

pedal right down will start it again.

before leaving the vehi-

cle.➥ 2.3.

2.4

CarManuals2.co

FUNCTION STOP AND START (2/3)

Preventing the engine from

Conditions for coming out of

Conditions preventing the

standing by

engine standby

standby of the engine

In certain situations, such as negotiat-

For vehicles equipped with auto-

Certain conditions prevent the system

ing a crossroads for instance, it is pos-

matic gearboxes:

from using the engine standby function,

sible (with the system activated) to keep

including when:

- the brake pedal is released, position

the engine running so as to be ready to

D or M engaged;

reverse gear is engaged;

move off quickly.

–

the bonnet is not locked;

For vehicles equipped with auto-

- the brake pedal is released in gear

matic gearboxes:

position N with the handbrake off;

–

the outdoor temperature is too low or

too high;

Keep the vehicle stationary without

- the brake pedal is pressed again,

the battery is not sufficiently charged;

pressing too hard on the brake pedal.

with N engaged and the handbrake

For vehicles equipped with manual

–

the difference between the vehicle

applied;

gearboxes:

interior temperature and the auto-

matic climate control instruction is

Keep the clutch pedal pressed right

- the vehicle is in gear position R;

too high;

down.

- the accelerator pedal is depressed.

parking distance control is in opera-

tion;

For vehicles equipped with manual

gearboxes:

the altitude is too high;

- the gearbox is in neutral and the

–

the gradient is too steep for vehicles

clutch pedal is slightly depressed;

fitted with a sequential gearbox;

the “Clear view” function is activated

- the engine is in gear and the clutch

➥ 3.7 ;

pedal is pressed right down.

the engine coolant temperature is

too low;

For vehicles equipped with a

manual gearbox

The restart may be interrupted if the

clutch pedal is released too quickly

while a gear is engaged.

2.5

CarManuals2.co

FUNCTION STOP AND START (3/3)

– automatic particle filter cleaning is

Deactivating, activating the

underway;

function

– the “Fast Idle Speed” function is acti-

Press 1 to deactivate the function.

vated ➥ 2.67 ;

The 2 switch warning light illuminates.

- ...

Pressing again will reactivate the

system. The indicator light 2 in switch 1

The warning light 

appears on the

goes out.

instrument panel to indicate that engine

standby is not available.

The system is automatically reactivated

each time the vehicle is started using

Special feature of the automatic

the start button. ➥ 2.3.

engine re-start

Under certain conditions, the engine

Operating faults

can restart on its own in order to guar-

antee your safety and comfort.

If warning light 2 lights up without press-

ing switch 1, the system is deactivated.

This can occur especially when:

- the vehicle speed is above 7 km/h

(downhill slope, etc.);

Please consult an authorised dealer.

- the outdoor temperature is too low or

too high;

- repeated pressing on the brake

pedal or braking system require-

- the “Clear view” function is activated

ment;

➥ 3.7 ;

- ...

– the battery is not sufficiently charged;

Special note: depending on the vehi-

cle, for some of these conditions the

automatic restarting of the engine is in-

hibited if a door is open.

Deactivate the Stop and

The engine MUST be

Start function for any opera-

stopped (not put in standby)

tion performed in the engine

before leaving the vehicle.

compartment.

➥ 2.3.

2.6

CarManuals2.co

SPECIAL FEATURES OF DIESEL VERSIONS (1/5)

Diesel engine speed

Precautions to be taken in

Diesel engines are equipped with an

winter

injection pump that is fitted with an

To avoid any faults in icy weather:

electronic regulator which prevents

make sure that the battery is always

over-revving of the engine irrespec-

fully charged;

tive of the gear engaged.

always keep the diesel tank rela-

If the Ä

and

warning lights

tively full to prevent water vapour

come on, consult an approved dealer

condensing in it and accumulating at

as soon as possible.

the bottom of the tank.

When driving, depending on the fuel

grade used, it is possible that white

smoke may be emitted.

This is due to the exhaust particle filter

being cleaned automatically, and does

not affect the way the vehicle runs.

Engine smoke opacity label

You can find the information 1 on the

label A stuck in the engine compart-

Running out of fuel

ment or, depending on the vehicle, on

You may start the engine normally after

the vehicle identification plate ➥ 6.2.

refilling the fuel tank even if you have

1 Diesel exhaust emissions.

completely run out of fuel, provided

that the battery is well-charged.

However, if after a few seconds, after

Do not park the vehicle or

several attempts, the engine does not

run the engine in locations

start ➥ 1.120.

where combustible sub-

stances or materials such as

grass or leaves can come into con-

tact with the hot exhaust system.

2.7

CarManuals2.co

SPECIAL FEATURES OF DIESEL VERSIONS (2/5)

Particle filter

Note: the warning light may reappear

if the driving conditions are not fully

The particle filter is used in the treat-

met with regard to cleaning the filter.

ment of exhaust gases from diesel en-

If the vehicle is stopped or the engine

gines.

speed is below approximately 2,000 rpm

Depending on the vehicle, the warning

before the warning light disappears

light 

displayed on the instrument

then you may have to restart the oper-

panel indicates that the filter is becom-

ation.

ing clogged and requires cleaning.

Automatic regeneration

To do this, when the 

warning

light is displayed, continue driving ac-

cording to traffic conditions and ob-

serve the speed limit until the warning

lights disappears. If possible, do not

let the engine speed drop below

2,000 rpm.

The warning light should go out after 10

to 20 minutes. ➥ 1.94.

The display of the 

warning light

on the instrument panel may be accom-

panied by an increase in engine speed

and operation of the cooling system in

order to clean the particle filter.

To facilitate the automatic particle

filter regeneration, carry out a long

driving phase (at least 20 minutes)

on main roads every 124 miles

(200 km).

2.8

CarManuals2.co

SPECIAL FEATURES OF DIESEL VERSIONS (3/5)

Manual regeneration of the particle

- press the 2 or 3 button repeatedly

filter leads to high temperature in the

until the message “Regenerate DPF

exhaust system and exhaust gases.

[long press]” appears;

Precautions must be taken into account

- press and hold the button 2 until the

(see below and on the following page)

“DPF regeneration Ongoing” or “40

during the process which lasts for ap-

min regen-to stop press brake” mes-

proximately 40 minutes.

sage appears.

To do this, when the 

warning

The warning light 

flashes.

light is on along with the “Regenerate

Wait until the warning light goes out

the particle filter” message:

(approximately 40 minutes).

- park your vehicle off the road, away

The message

“DPF Regeneration

from traffic and in a place where it is

Completed” is displayed on the instru-

at least three metres from any obsta-

ment panel.

cles or material which could easily

ignite or melt

(e.g. paper, grass,

If the conditions are not met before or

Manual regeneration

plastic, dry organic material, etc.);

(depending on the vehicle)

during regeneration, the 

warning

- apply the handbrake;

light goes out and the message “DPF

If it is not possible to comply with the

Regeneration Interrupted” is displayed

conditions (driving time required, etc.),

- position the gear lever in neutral (N)

and the procedure is cancelled.

position on vehicles equipped with

the 

warning light is displayed

an automatic gearbox).

The “Regenerate DPF [long press]”

on the instrument panel accompanied

message will be displayed as soon as

Then, with the engine running:

by the message “Regenerate the parti-

the conditions required to renew the

cle filter” to indicate that the saturation

- deactivate the Stop and Start func-

manual procedure are once again met.

level is too high for automatic regener-

tion if the vehicle is equipped with it

ation.

➥ 2.4;

You must quickly carry out manual re-

generation to avoid saturation of the

particle filter which may require you to

consult an approved dealer.

2.9

CarManuals2.co

SPECIAL FEATURES OF DIESEL VERSIONS (4/5)

Note: do not start the regeneration in

During the regeneration process:

If you need to interrupt the particle

the event of an insufficient oil or coolant

filter regeneration, press one of the

the engine speed first increases to

pedals. In this case, regeneration will

approximately 3,000 rpm in order to

level (oil pressure warning light À

only be partial.

warm the engine. It then decreases

or coolant temperature warning light

to approximately 1,700 rpm until the

lit on the instrument panel). In

end of the regeneration;

this case, top-up ➥ 4.4 and ➥ 4.8.

the fan assemblies are triggered.

Regeneration is not possible:

This is normal operation to ensure

engine cooling;

if the fuel level is too low;

Do not start the regenera-

white fumes and unusual odours are

tion in a garage or a con-

–

if the engine is too cold;

frequently produced in the exhaust

fined area.

–

in extreme weather conditions (cold,

system. This does not indicate that

hot or very high altitude).

the system is operating incorrectly.

Risk of poisoning or suf-

focation by exhaust gas emis-

sions.

Make sure that no one is near the

exhaust when regenerating.

Risk of burns.

Do not park the vehicle in locations

where combustible substances or

materials such as grass, leaves or

paper may come into contact with or

be near to the hot exhaust system.

Fire hazard.

Do not leave your vehicle unsu-

pervised during regeneration.

2.10

CarManuals2.co

SPECIAL FEATURES OF DIESEL VERSIONS (5/5)

Special cases

If the filter becomes excessively sat-

urated, the

warning light and,

depending on the vehicle, the 

warning light will appear on the instru-

ment panel, accompanied by the mes-

sage “Check injection”. In this case,

please consult an Authorised Dealer.

If the

warning light and, de-

pending on the vehicle, the



warning light appears, accompanied by

the “WARNING: Engine Failure Risk”

message, stop the vehicle, switch off

the engine and contact an Approved

Dealer.

Warning light

re-

quires you to stop immedi-

ately, for your own safety,

as soon as traffic conditions

allow. Switch off the engine and do

not restart it. Contact an approved

Dealer.

2.11

CarManuals2.co

DRIVING ADVICE, ECO-DRIVING (1/5)

Fuel consumption is accredited in ac-

cordance with a standard regulatory

method. Identical for all manufactu-

rers, this enables vehicles to be com-

pared with one another. Consumption

in real time depends on vehicle usage

conditions, the equipment fitted and the

user’s driving style. To optimise fuel

consumption, please refer to the fol-

lowing advice.

Depending on the vehicle, you will have

various functions which enable you to

lower your fuel consumption:

- the rev counter;

- gear change indicator;

Gear change indicator 1

- the journey record and eco-driving

advice via the multimedia display;

To optimise consumption levels,

warning light on the instrument panel A

- ECO mode activated by the ECO

or B indicates the best time to move up

button;

or down a gear:

- the Stop and Start function ➥ 2.4.

If fitted on the vehicle, the navigation

upshift a gear;

system provides additional information.

[

downshift a gear.

If you regularly follow this indicator, you

will reduce your vehicle’s fuel consump-

tion.

2.12

CarManuals2.co

DRIVING ADVICE, ECO-DRIVING (2/5)

An overall rating from 0 to 100 is dis-

played to let you assess your eco driv-

ing performance. The higher the rating,

the lower the fuel consumption.

Eco advice is given to help improve

your performance.

With your favourite journeys saved, you

can evaluate your performance.

For more information, please see the

multimedia system instructions.

Journey record

Once the engine is switched off, you

will see “Journey record” displayed on

the screen 2, enabling you to view in-

formation relating to your last journey.

This indicates:

- average fuel consumption;

- number of miles/kilometres travelled;

- number of miles/kilometres saved.

2.13

CarManuals2.co

DRIVING ADVICE, ECO-DRIVING (3/5)

ECO mode

Activating the function

Disabling the function

ECO mode is a function which opti-

Press switch 4.

mises fuel consumption. It acts on cer-

tain power consuming systems in the

The 3 

warning light comes on on

Warning light 3 

goes out on the

vehicle (heating, air conditioning, pow-

the instrument panel A or B to confirm

instrument panel to confirm deactiva-

er-assisted steering, etc.) and on cer-

activation.

tion.

tain driving actions (acceleration, gear

While driving, it is possible to leave the

changing, cruise control, deceleration,

ECO mode temporarily in order to im-

etc.).

prove engine performance.

Limiting acceleration enables low fuel

To do this, press the accelerator pedal

consumption in urban and surrounding

firmly and fully.

areas. When ECO mode is in use, it is

normal for changes in the heating level

ECO mode is reactivated when you

to occur.

take pressure off the accelerator pedal.

2.14

CarManuals2.co

DRIVING ADVICE, ECO-DRIVING (4/5)

High speeds significantly affect

Double declutching and accelerating

the vehicle’s fuel consumption.

before switching off are unnecessary

Examples (at a steady speed):

in modern vehicles.

– reducing the speed from 80 mph

Bad weather, flooded roads:

(130 km/h) to 68 mph (110 km/h) ap-

proximately saves up to 20% of fuel

Do not drive through

approximately;

floods if the water is

- reducing the speed from 56 mph

above the lower edge of

(90 km/h) to 50 mph (80 km/h) ap-

the wheel rims.

proximately saves up to 10% of fuel

approximately.

Do not overrev the engine in the in-

termediate gears.

You should always use the highest

gear possible.

Avoid sudden acceleration.

Driving advice, Eco-driving

–

Brake as little as possible. If you an-

Behaviour

ticipate an obstacle or bend in ad-

- Drive carefully for the first few miles

vance, you may then simply release

until the engine reaches its normal

the accelerator pedal.

operating temperature, rather than

Do not try to maintain the same

let it warm up while the vehicle is sta-

Obstructions to the driver

speed up a hill, accelerate no more

tionary.

than you would on the level. Keep

On the driver’s side, only

- Dynamic driving with a lot of frequent

your foot in the same position on the

use mats suitable for the

acceleration and braking is expen-

accelerator pedal.

vehicle, attached with the

sive on fuel in comparison to the time

pre-fitted components, and check

saved.

the fitting regularly. Do not lay one

mat on top of another.

There is a risk of wedging the

pedals.

2.15

CarManuals2.co

DRIVING ADVICE, ECO-DRIVING (5/5)

In vehicles fitted with air condi-

tioning, it is normal to observe an

increase in fuel consumption (espe-

cially in urban conditions) when it is

used. For vehicles fitted with manual

air conditioning, switch off the system

when it is not required.

Recommendations for reducing

consumption and therefore help-

ing to preserve the environment:

If the vehicle has been parked in the

sun, open the doors for a few mo-

ments to let the hot air escape before

starting the engine.

Do not leave an empty roof rack

Tyres

Advice on use

fitted to the vehicle.

– An underinflated tyre increases fuel

- Favour the ECO mode.

When towing a caravan, fit a wind

consumption.

- Electricity is fuel - switch off all the

deflector and adjust it carefully.

- The use of non-recommended tyres

electrical components when they

can increase fuel consumption.

are not genuinely needed. However

(safety first), keep your lights on

when the visibility is bad (“see and

be seen”).

- Use the air vents. Driving with the

windows open at 62 mph (100 km/h)

will increase fuel consumption by

4%.

- Never fill the fuel tank right to the

brim to avoid overflow.

2.16

CarManuals2.co

MAINTENANCE AND ANTIPOLLUTION ADVICE

Your vehicle complies with criteria for

Maintenance

Exhaust gas monitoring

recycling and recovering vehicles at the

It is important to remember that failure to

system

end of their service life, which entered

respect antipollution regulations could

The exhaust gas monitoring system will

into force in 2015.

lead to legal action being taken against

detect any operating faults in the vehi-

Some parts of your vehicle have there-

the vehicle owner. In addition, replacing

cle’s antipollution system.

fore been designed to facilitate future

engine, fuel supply system and exhaust

If this system malfunctions, toxic sub-

recycling.

components with parts other than those

stances may be released into the at-

These parts are easy to remove so

originally recommended by the manu-

mosphere or damage may occur.

facturer may alter your vehicle so that

that they can be recovered and repro-

This warning light on the in-

it no longer complies with antipollution

cessed by recycling companies.

strument panel will indicate if

regulations.

By virtue of its design, moderate fuel

there are any faults in the system:

consumption and initial settings, your

Have your vehicle adjusted and

This lights up when the ignition is

vehicle also conforms to current an-

checked by an approved Dealer, in ac-

switched on and goes out when the

tipollution regulations. The manufac-

cordance with the instructions given in

engine is started.

turer is actively striving to reduce pol-

your maintenance schedule: they will

- If it lights up continuously, consult an

lutant exhaust gas emissions and to

have all the equipment necessary for

approved Dealer as soon as possi-

save energy. But the fuel consumption

ensuring that your vehicle is maintained

ble;

of your vehicle and the level of pollutant

to its original standard.

- if it flashes, reduce the engine speed

exhaust gas emissions are also your

until the light stops flashing. Contact

responsibility. Ensure that it is main-

your approved dealer as soon as

Engine adjustments

tained and used correctly.

possible.

- Air filter, diesel filter: a choked el-

ement will reduce efficiency. It must

 ^{➥ 1.123}

be replaced.

- Idle speed: this does not require ad-

justment.

2.17

CarManuals2.co

ENVIRONMENT

Your vehicle has been designed with

Emissions

- At the end of the vehicle’s service

respect for the environment in mind for

life, it should be sent to approved

Your vehicle has been designed to emit

its entire service life: during production,

centres to ensure that it is recycled.

fewer greenhouse gases (CO2) while in

use and at the end of its life.

use, and therefore to consume less fuel

- In all cases, comply with local legis-

(eg. 140 g/km, equivalent to 5.3 l/100

lation.

Manufacture

km for a diesel vehicle).

Your vehicle has been manufactured at

Our vehicles are also equipped with a

Recycling

an industrial site which uses a progress

particle filter system including a cata-

Your vehicle is 85% recyclable and

policy to reduce environmental impacts

lytic converter, an oxygen sensor and

95% recoverable.

on rivers and natural areas (reduc-

an active carbon filter (the latter pre-

tion of water and energy consumption,

vents vapour from the fuel tank being

To achieve these objectives, many of

visual and noise pollution, atmospheric

released into the open air).

the vehicle components have been de-

emissions and waste water, sorting and

signed to enable them to be recycled.

For certain diesel vehicles, this system

reusing waste).

The materials and structures have

also has a particle filter to reduce the

been carefully designed to allow these

volume of soot particles emitted.

components to be easily removed and

reprocessed by specialist companies.

Please make your own

In order to preserve raw material re-

contribution towards

sources, this vehicle incorporates nu-

protecting the environment

merous parts made from recycled plas-

tics or renewable materials (vegetable

too

or animal-derived materials such as

- Worn parts replaced in the course of

cotton or wool).

routine vehicle maintenance (vehi-

cle battery, oil filter, air filter, batter-

ies, etc.) and oil containers (empty or

filled with used oil) must be disposed

of through specialist organisations.

2.18

CarManuals2.co

Renault Master (2023 year). Manual in english - page 3