Renault Kangoo (2023 year). Manual in english

“HANDS-FREE” CARD: battery (1/2)

The batteries are available from ap-

proved Dealers, and their service

life approximately two years. Check

that there is no dye on the battery:

risk of an incorrect electrical con-

tact.

If they need to be replaced,

Replacing the battery

When refitting, proceed in the reverse

be sure to use the same

order, then press one of the buttons on

When the message “Keycard Battery

or equivalent type of bat-

the card four times, close to the vehicle:

Low” appears on the instrument panel,

tery (consult an Approved

the next time the vehicle is started, the

replace the battery in the card:

Dealer).

message will disappear.

- slide the rear casing 1 downwards

while pressing on zone A;

Check that the cover is clipped shut.

- remove the battery cover 2;

Note: Do not touch the electronic circuit

- remove the battery by pressing on

or contacts on the card when replacing

one side and lifting the other;

the battery.

When replacing:

- replace it according to the direc-

tion and template shown inside the

- make sure that the batter-

cover.

ies are correctly inserted.

Risk of explosion.

- if the flap does not close cor-

rectly, do not use and keep out of

reach of children.

5.29

CarManuals2.co

“HANDS-FREE” CARD: battery (2/2)

Operating faults

If the battery is too weak to ensure cor-

rect operation, you will still be able to

start and lock/unlock the vehicle

➥ 1.29.

Precautions relating to

batteries:

- keep (new or used) bat-

teries out of reach of chil-

dren;

- do not swallow batteries;

Risk of chemical burns which

may lead to death.

- if ingested or inserted into any

part of the body, consult a doctor

as soon as possible.

Do not throw away your used bat-

teries; give them to an organisation

responsible for collecting and recy-

cling batteries.

5.30

CarManuals2.co

BATTERY: troubleshooting (1/2)

To avoid all risk of sparks:

Connecting a battery charger

Ensure that any power consumers

The battery charger must be com-

(courtesy lights, etc.) are switched

patible with a battery with nominal

off before disconnecting or recon-

voltage of 12 volts.

necting a battery;

Do not disconnect the battery when the

when charging, stop the charger

engine is running. Follow the instruc-

before connecting or disconnecting

tions given by the manufacturer of

the battery;

the battery charger you are using.

do not place metal objects on the

battery as this could create a short

Handle the battery with care

circuit between the terminals;

as it contains sulphuric acid,

always wait at least five minutes

which must not come into

after the engine has been switched

contact with eyes or skin. If

off before disconnecting a battery;

it does, wash the affected area with

make sure that you reconnect the

plenty of cold water. If necessary,

battery terminals after refitting.

consult a doctor.

Keep naked flames, red hot objects

and sparks away from the battery

components as there is a risk of

explosion.

Special procedures may be

Please note when working close to

required to charge some

the engine that it may be hot. In ad-

batteries. Contact your ap-

dition, the engine cooling fan may

proved dealer.

Avoid all risk of sparks which may

start at any moment. The 

cause an immediate explosion, and

warning light in the engine compart-

charge the battery in a well venti-

ment reminds you of this.

lated area.

Risk of injury.

Before carrying out any

Risk of serious injury.

action in the engine com-

partment, you must switch

off the ignition.

➥ 2.4

➥ 2.5.

5.31

CarManuals2.co

BATTERY: troubleshooting (2/2)

Starting the vehicle using the

battery from another vehicle

If you have to use the battery from an-

other vehicle to start, obtain suitable

jump leads (with a large cross section)

from an approved dealer or, if you al-

ready have jump leads, ensure that

they are in perfect condition.

The two batteries must have an iden-

tical nominal voltage: 12 volts. The

battery supplying the current should

have a capacity (amp-hours, Ah) which

is at least the same as that of the dis-

charged battery.

Ensure that there is no risk of contact

Lift the red cover on box 2 located

Start the engine, and as soon as it starts

between the two vehicles (risk of short

behind the battery.

running, disconnect cables A and B in

circuiting when the positive terminals

reverse order ( 4 - 5 - 6 - 1).

are connected) and that the discharged

Connect the positive cable A to the

After repairing, ensure that the protec-

battery is properly connected. Switch

support 1 ( + ) located under the box

tive foam and the cover 3 are in place.

off your vehicle ignition.

cover 2, then to the terminal 6 ( + ) of

the battery supplying the current.

Start the engine of the vehicle supply-

ing the current and run it at an interme-

Remove the cover 3 and the protective

foam located underneath. Connect the

Check that there is no con-

diate engine speed.

negative cable B to terminal 5 ( - ) of

tact between leads A and B

the battery supplying the current then

and that the positive lead A

to the metal cable 4 ( - ) of the dis-

is not touching any metal

charged battery.

parts on the vehicle supplying the

current.

Risk of injury and/or damage to

the vehicle.

5.32

CarManuals2.co

FITTING A RADIO

In all cases, it is very important to

follow the manufacturer’s instruc-

tions carefully.

The specifications of the brack-

Radio location 1

Front door speakers 2

ets and wires (available from our

Unclip the blanking cover. The connec-

To install any equipment, please con-

network) vary depending on the

tions: ( + aerial) and ( - supply and

sult an authorised dealer.

equipment level of your vehicle

speaker) are located behind it.

and the type of radio.

Consult an approved Dealer to

find out the correct part number.

No work may be carried out on

the vehicle’s electrical or radio

circuits, except by approved

dealers: an incorrectly connected

system may result in damage

being caused to the electrical

equipment and/or the compo-

nents connected to it.

5.33

CarManuals2.co

ACCESSORIES

Electrical and electronic accessories

Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po-

sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.

Before connecting an accessory to a socket, please ensure that you do not exceed the maximum power authorised for

the socket. ➥ 3.32, ➥ 3.16. Fire hazard.

No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected

system may result in damage being caused to the electrical equipment and/or the components connected to it.

If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.

Establish the rating and position of this fuse.

Using the diagnostic socket

The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems.

For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved

Dealer. Serious accident risk.

Fitting aftermarket accessories

If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of

your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your

vehicle, which are the only accessories for which the manufacturer will provide a warranty.

If you are using an anti-theft device, only attach it to the brake pedal.

Obstructions to the driver

On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting reg-

ularly. Do not lay one mat on top of another. There is a risk of wedging the pedals.

5.34

CarManuals2.co

FUSES (1/3)

Fuse boxes

Tweezers 3

If any electrical component does not

Remove the fuse using the tweezers 3

work, check the condition of the fuses.

on the back of the flap.

To remove the fuse from the tweezers,

Passenger compartment fuses

slide the fuse to the side.

Check the fuse in question

Place your hand in location 2 and pull to

It is not advisable to use the free fuse

and replace it, if neces-

open the flap 1.

locations.

sary, by a fuse of the same

Depending on the vehicle, to identify

rating.

the fuses, refer to the fuse allocation

If a fuse is fitted with too high a

label located at the back of the flap 1

rating, it may cause the electrical

and shown on the following pages.

circuit to overheat (risk of fire) in the

event of an item of equipment using

an excessive amount of current.

To comply with current legislation, or

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

bulbs and fuses.

5.35

CarManuals2.co

FUSES (2/3)

Allocation of fuses

(the presence of certain fuse depends on the vehicle equipment level)

Symbol

Allocation

Windscreen washer

Front headlights

Hazard warning lights

Horn

Towbar socket

Brake lights, passenger compartment central unit

Use the fuse allocation label in the

Screen washer, rear lights

storage compartment to identify the

fuses.

Certain fuses should only be re-

Direction indicators

placed by a qualified professional.

These fuses are not listed on the

label.

Accessories socket

Only change the fuses represented

on the label.

Electric windows



5.36

CarManuals2.co

FUSES (3/3)

Please note when work-

ing close to the engine that

it may be hot. In addition,

Fuses in engine compartment A

the engine cooling fan may

Some functions are protected by fuses

located in the engine compartment

start at any moment. The 

(unit A).

warning light in the engine compart-

ment reminds you of this.

However, because of their reduced

accessibility, we advise you to have

Risk of injury.

your fuses replaced by an approved

Dealer.

Before carrying out any

action in the engine com-

partment, you must switch

off the ignition.

➥ 2.4 or

➥ 2.5.

5.37

CarManuals2.co

WIPER BLADES: replacement (1/2)

Replacing the windscreen

To refit

wiper blades 2

To refit the wiper blade 2, insert it in its

To replace the wipers, first put them in

housing in the arm 3, then clip it until

the service positionB.

you hear a click. Make sure that the

With the ignition on and the engine

blade is correctly locked in position.

stopped:

To return the blades to lowered posi-

- move the stalk twice in succession 1

Check the condition of the wiper

tion, make sure that the blades are

to position A (single sweep): the

blades. You are responsible for their

folded down onto the windscreen then

wiper blades will stop in the service

service life:

set the 1 stalk to position A (single

position B away from the bonnet;

- clean the blades, windscreen and

sweep): the windscreen wiper blades

- lift the wiper arm 3;

rear screen regularly with soapy

will fold into the bonnet when the igni-

- lower the 4 tab then remove the

water;

tion is switched on.

blade 2.

- do not use them when the wind-

screen or rear screen are dry;

- free them from the windscreen or

rear screen when they have not

been used for a long time.

5.38

CarManuals2.co

WIPER BLADES: replacement (2/2)

- In frosty weather, make

sure that the wiper blades

are not stuck by ice

(to

avoid the risk of the motor

overheating).

- Check the condition of the wiper

blades. Replace the wiper blades

Rear screen wiper blade 5

as soon as they begin to lose ef-

Stalk in stop position (deactivated):

ficiency

(approximately once a

- lift the wiper arm 6;

year).

- turn the blade horizontally 5 (move-

When changing the blade, when it

ment C) until it unclips;

has been removed, do not let the

Check the condition of the wiper

- remove the blade by pulling it.

wiper arm fall against the window:

blades.

risk of breaking the window.

To refit

- clean the blades, windscreen and

rear screen regularly with soapy

To refit the wiper blade, proceed in re-

water;

verse order to removal. Make sure that

the blade is correctly locked in position.

- do not use them when the wind-

screen or rear screen are dry;

Before changing the rear

wiper blade, make sure the

- free them from the windscreen or

stalk is in the stop position

rear screen when they have not

(deactivated).

been used for a long time.

Risk of injury.

5.39

CarManuals2.co

TOWING: breakdown recovery (1/2)

Before carrying out any towing, posi-

The speed specified by current legis-

tion the gearbox in neutral position (po-

lation for towing must always be ob-

sition N on vehicles equipped with an

served. If you are driving the towing

automatic gearbox), unlock the steering

vehicle, do not exceed the permissible

column then release the parking brake.

towing weight for your vehicle. ➥ 6.10.

Steering column unlocking

Towing a vehicle fitted with

Insert the key into the ignition, set to

an automatic gearbox

“On” ON 2 position or, depending on

the vehicle, with the card in the pas-

Transport the vehicle on a trailer or tow

senger compartment, press the engine

it with the front wheels off the ground.

start button for approximately two sec-

In exceptional circumstances, you

onds.

may tow it with all four wheels on the

ground, only in a forward gear, with the

Reposition the lever to neutral (position

gearbox in neutral position N, over a

N for vehicles fitted with an automatic

maximum distance of 50 miles (80 km)

gearbox).

and not exceeding a speed of 16 mph

When starting, if the lever is locked in

The steering column unlocks, the ac-

(25 km/h).

position P even though you are press-

cessory functions are powered: you

ing the brake pedal, the lever can be re-

can use the vehicle’s lights (direction

leased manually in order to unlock the

indicators, brake lights, etc.). At night

drive wheels.

the vehicle must have its lights on.

To do this, unclip the base of the gaiter

Depending on the vehicle, once you

and press the 2 button while simultane-

When the engine is stopped,

have finished towing, press the engine

ously pressing the 1 button on the lever

steering and braking assist-

start button twice (risk of running down

to unlock the lever and shift to position

ance are not operational.

the battery).

Contact an authorised dealer as soon

as possible.

Leave the card in the vehi-

cle during towing.

Risk of the steering

column locking.

5.40

CarManuals2.co

TOWING: breakdown recovery (2/2)

Tighten the towing hitch 5 fully: first

by hand until it stops, then finish by

locking it with the wheel brace or, de-

pending on the vehicle, the lever.

Only use the towing hitch 5 and the

wheelbrace or lever provided with the

tools. ➥ 5.8.

- Use a rigid towing bar.

If a rope or cable is used

(where the law allows this),

the vehicle being towed

Only use the front 4 and rear 7 towing

Access to towing points

must be able to brake.

points (never use the driveshafts or any

A vehicle must not be towed if it is

other part of the vehicle). These towing

Front towing point 4

not fit to be driven.

points may only be used for pulling.

Avoid accelerating or braking

Unclip the cover 3 by inserting a flat-

They must never be used for lifting the

suddenly when towing, as this

blade screwdriver or similar into the

vehicle directly or indirectly.

may result in damage being

groove A.

caused to the vehicle.

In all cases, it is advisable not to

Rear towing point 7

exceed 15.5 mph (25 km/h).

Unclip the cover 6 by inserting a flat-

blade screwdriver or similar into the

groove B.

Ensure that the towing eye

Do not leave the tools unse-

is bolted correctly.

cured inside the vehicle as

they may come loose under

Risk of losing the towed

braking.

object.

5.41

CarManuals2.co

OPERATING FAULTS (1/8)

Using the card

POSSIBLE CAUSES

WHAT TO DO

The card does not lock or unlock the

Card battery is flat.

Replace the battery. You will still be able to

doors.

lock/unlock and start your vehicle. ➥ 1.29

and ➥ 2.4 or ➥ 2.5.

Use of appliances operating on the

Stop using the devices or use the key pro-

same frequency as the card (mobile

vided. ➥ 1.29.

phone, etc.).

Vehicle located in a high electromag-

Use the key that is built into the card

netic radiation zone.

➥ 1.29.

Vehicle battery flat.

The message “Place card on zone +

Place the card in the placement area

START” appears on the instrument

➥ 2.5 then press the START button.

panel.

The vehicle is started.

With the engine running, the card’s locking/

unlocking device is blocked. Turn off the ig-

nition.

Desynchronisation of the card

Unlock the driver’s door by inserting the

key integrated in the card into the door lock

➥ 1.29 then place the card in the placement

area ➥ 2.5 and press the START button to

synchronise the card.

5.42

CarManuals2.co

OPERATING FAULTS (2/8)

The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact

an approved dealer as soon as possible.

Using the remote control

POSSIBLE CAUSES

ACTION REQUIRED

The remote control does not lock or The remote control battery is flat.

Use the emergency key.

unlock the doors.

Use of appliances operating on the same

Stop using the devices or use the key.

frequency as the remote control (mobile

phone, etc.).

Vehicle located in a high electromagnetic

Replace the battery. You will still be able to

radiation zone.

lock/unlock and start your vehicle. ➥ 1.29

Discharged battery.

and ➥ 2.4 or ➥ 2.5.

The vehicle is started.

With the engine running, the key’s locking/

unlocking device is blocked. Turn off the

ignition.

Desynchronisation of the remote control

Unlock the driver’s door by inserting the

key into the door lock ➥ 1.29, then start

the engine to synchronise the remote con-

trol ➥ 2.4.

5.43

CarManuals2.co

OPERATING FAULTS (3/8)

The starter is activated

POSSIBLE CAUSES

ACTION REQUIRED

The instrument panel indicator lights are

Battery terminals not tight, bat-

Retighten or reconnect the terminals, or clean them if

weak or fail to light up and the starter

tery terminals disconnected or

they are oxidised.

does not turn.

oxidised.

Discharged battery or not op- Connect another battery to the faulty battery. ➥ 5.31 or

erational.

replace the battery if necessary.

Do not push the vehicle if the steering column is

locked.

Faulty circuit.

Consult an approved dealer.

The engine will not start.

Starting conditions are not ful- ➥ 2.4 or ➥ 2.5.

filled.

The “hands-free” card does not Place the card in the recess provided for this purpose

work.

on the centre console ➥ 2.4 or ➥ 2.5.

With the vehicle stationary, engine cold, Petrol version, this is not nec-

The engine’s idle speed should decrease after about

the engine’s idle speed is high.

essarily a fault. This may be

one minute. Otherwise, this may be caused by an-

caused by the increase in the

other fault. Call an approved Dealer.

engine temperature.

The engine cannot be switched off.

Card not detected.

Place the card in the recess provided for this purpose

on the centre console.

Press and hold the start button.

Electronic fault.

Press the start button 3 times quickly or press and

hold.

The steering column remains locked. Steering wheel locked.

Move the steering wheel while pressing the engine

start button (or, depending on the vehicle, operating

the ignition key) ➥ 2.4.

Faulty electrical circuit.

Consult an approved dealer.

5.44

CarManuals2.co

OPERATING FAULTS (4/8)

On the road

POSSIBLE CAUSES

WHAT TO DO

Vibrations.

Tyres not inflated to correct pres-

Check the tyre pressures: if this is not the

sures, incorrectly balanced or dam-

problem, have them checked by an ap-

aged.

proved Dealer.

White smoke from the exhaust.

In the diesel version, this is not neces-

➥ 2.14.

sarily a fault. Smoke may be caused

by particle filter regeneration.

Petrol version, this is not necessarily

Reduce the engine speed and avoid

a fault. Depending on the climate con-

sudden acceleration to gradually make the

ditions (cold, humidity etc.), smoke

smoke disappear. Otherwise, this may be

may be produced under hard vehicle

caused by another fault. Consult an ap-

acceleration.

proved dealer.

Smoke under the bonnet.

Short-circuit or cooling system leak.

Stop, switch off the ignition, stand away

from the vehicle and contact an approved

dealer.

The oil pressure warning light comes

on:

while cornering or braking,

The level is too low.

Top up the engine oil ➥ 4.5.

is slow to go out or remains lit up

Loss of oil pressure.

Stop the vehicle and contact an approved

under acceleration.

Dealer.

5.45

CarManuals2.co

OPERATING FAULTS (5/8)

On the road

POSSIBLE CAUSES

WHAT TO DO

Steering becomes heavy.

Assistance overheating.

Drive carefully at reduced speed, be aware

of the level of force in the steering wheel

needed to turn the wheels.

Fault with the electric assistance

Consult an authorised dealer.

motor.

Fault in the assistance system

The engine is overheating. The

Engine cooling fan not working.

Stop the vehicle, switch off the engine and

coolant temperature indicator is in

contact an approved dealer.

the warning zone and warning light

comes on.

Coolant leaks.

Check the coolant reservoir: it should con-

tain fluid. If there is no coolant, consult an

authorised dealer as soon as possible.

Coolant boiling in the coolant reser-

Mechanical fault: damaged cylinder

Stop the engine.

voir.

head gasket.

Contact an approved dealer.

Radiator: if there is a significant lack of coolant, remember that it must never be topped up using cold coolant when the

engine is very hot. After any procedure on the vehicle which has involved even partial draining of the cooling system,

it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved by our

Technical Department may be used for this purpose.

5.46

CarManuals2.co

OPERATING FAULTS (6/8)

Stopped

POSSIBLE CAUSES

WHAT TO DO

The engine cooling fan starts to run

This is not necessarily a fault. The

after the ignition is switched off.

engine cooling fan group may start

to run in order to regulate the engine

temperature. This operation may last

several minutes after the engine is

switched off.

The engine cooling fan runs for more

Consult an approved dealer.

than 10 minutes after the engine is

switched off.

5.47

CarManuals2.co

OPERATING FAULTS (7/8)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

The wipers do not work.

Wiper blades stuck.

Free the blades before using the wipers.

Faulty electrical circuit.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.35.

The wiper does not stop.

Faulty electrical controls.

Consult an approved dealer.

Direction indicators flashing more

Blown rear bulb.

➥ 5.18.

quickly.

The direction indicators do not work.

Faulty electrical circuit or control.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.35.

The lights do not come on or go off.

Faulty electrical circuit or control.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.35.

5.48

CarManuals2.co

OPERATING FAULTS (8/8)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

Traces of condensation in the head-

Traces of condensation may be a nat-

lights or rear lights.

ural phenomenon caused by varia-

tions in temperature and humidity.

In this case, the traces will disappear

slowly once the lights are switched

on.

The front seat belt reminder light

An object is stuck between the floor

Remove all objects from underneath the

comes on when the seat belts are

and the seat and is disrupting the op-

front seats.

fastened.

eration of the sensor.

5.49

CarManuals2.co

VEHICLE IDENTIFICATION PLATES

The information shown on the ve-

MMAC (Maximum Authorised

hicle identification plate should be

Mass.

quoted on all correspondence or

MTR (Gross Train Weight: vehicle

orders.

fully loaded, with trailer).

MMTA (Maximum Permissible

The presence and location of the in-

Weight) front axle.

formation depends on the vehicle.

MMTA rear axle.

Reserved for related or additional

Vehicle identification plate A

entries.

Manufacturer name.

Diesel exhaust emissions.

EC design number or approval

Depending on the vehicle, this

number.

information is not indicated on

Identification number.

the manufacturer’s plate but on

Depending on the vehicle, this

the engine smoke opacity label

information is also given on

➥ 2.14.

marking B.

Paint reference (colour code).

6.2

CarManuals2.co

TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES

The QR Code on the A label allows

Note: vehicles without rear windows

emergency workers using a tablet or

have only the front label affixed.

smartphone to immediately access the

technical information useful for working

on the vehicle in the event of an acci-

dent.

Ensure that the A label is always visible

and present on the windscreen as well

as the rear screen.

Any modification or damage would

prevent access to the information.

6.3

CarManuals2.co

DIMENSIONS (in metres) (2/2)

“Standard chassis”

“Long chassis”

0,962

2,716

3,100

0,810

0,848

4,487

4,910

Door mirrors folded in

1,919

Door mirrors folded out

2,159

1,580

1,600

Estate version

1,810

H (unladen)

Van version

1,830

Turning circles between kerbs

10,9

12,4

Turning circles between walls

11,2

13,1

Caution: if the vehicle is fitted with roof bars, the height must be increased by 0,052 m (the bars cannot be removed).

6.6

CarManuals2.co

ENGINE SPECIFICATIONS (2/3)

Versions

1.3 TCe

1.5 dCi

Engine type

H5H Turbo

K9K Turbo

(see engine plate)

Cubic capacity (cc)

1 332

1461

Fuel types that meet

European standards and are

compatible with the engines

Unleaded petrol compliant with

Diesel fuel compliant with stand-

of vehicles sold in Europe

standard EN 228 contains up

ard EN 590 contains up to 7%

(in any other case, contact an

to 5% ethanol in volume.

fatty acid methyl ester in volume.

Approved Dealer).

Unleaded petrol compliant with

Diesel fuel compliant with stand-

standard EN 228 contains up

ard EN 16734 contains up to 10%

to 10% ethanol in volume.

fatty acid methyl ester in volume.

Diesel fuel compliant with stand-

ard EN 15940 contains up to 7%

acid methyl ester in volume.

6.8

CarManuals2.co

ENGINE SPECIFICATIONS (3/3)

Versions

1.3 TCe

1.5 dCi

Engine type

H5H Turbo

K9K Turbo

(see engine plate)

Cubic capacity (cc)

1 332

1461

Spark plugs

Only use the spark plugs specified for your vehicle’s

engine.

The type should be marked on a label affixed inside

the engine compartment. If it is not then contact an

approved Dealer.

Fitting spark plugs other than those specified may

damage the engine.

6.9

CarManuals2.co

WEIGHTS (in kg)

The weights indicated for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult

your approved Dealer.

Van version

Estate versions

Versions

Standard chassis

Long chassis

Standard chassis

Maximum Authorised Mass (MMAC)

Maximum permissible weight (MMTA)

Weights indicated on the vehicle identification plate ➥ 6.2

Gross Train Weight (MTR)

Braked Trailer Weight*

found by calculating: MTR - MMAC

Unbraked Trailer Weight*

685 kg

750 kg

Permissible nose weight*

75 kg

Maximum permissible load on roof

➥ 3.44, ➥ 3.46

* Towing weight (Towing a caravan, boat, etc.)

Towing is prohibited when the MTR-MMAC calculation is equal to zero, or when the MTR is equal to zero (or is not listed) on the

identification plate.

- It is important to respect local towing regulations in force, specifically those set out in the Highway Code. Please contact your

authorised dealer about adapting any towing equipment.

- When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded. However the following is

permitted:

- rear axle MMTA exceeded by no more than 15%,

- maximum MMAC exceeded by no more than 10% or 100 kg (whichever is reached first).

In either case, the maximum speed of the vehicle and trailer must not exceed 48 mph (80 km/h) (van versions) or 60 mph

(100 km/h) (estate versions) and the tyre pressure must be increased by 0.2 bar (3 PSI).

- The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10%

at an altitude of 1,000 metres and by an additional 10% for each 1,000 metres thereafter.

6.10

CarManuals2.co

REPLACEMENT PARTS AND REPAIRS

Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same

level of quality as the parts fitted originally.

If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out

within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the

repair order.

6.11

CarManuals2.co

SERVICE SHEETS (1/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.12

CarManuals2.co

SERVICE SHEETS (2/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.13

CarManuals2.co

SERVICE SHEETS (3/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.14

CarManuals2.co

SERVICE SHEETS (4/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.15

CarManuals2.co

SERVICE SHEETS (5/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.16

CarManuals2.co

SERVICE SHEETS (6/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.17

CarManuals2.co

Renault Kangoo (2023 year). Manual in english - page 9