Renault Kangoo E-Tech (2023 year). Manual in english

INTERIOR LIGHTING: changing bulbs (2/6)

Front map reading lights 6

Refitting

(depending on the vehicle)

- Clip the lens 7 on to the bulb holder 8;

- Unclip the lens 7 (using a tool such

- clip in the reading spots block 6 until

as a flat screwdriver), positioned

the unit clicks;

at B;

- make sure that the reading spots

- unclip and release the bulb

block is correctly positioned and

holder 8 using the tabs 9;

locked into place.

- remove the bulb concerned.

Type of bulb 10: W5W.

5.23

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (3/6)

Rear reading spot 11

Refitting

(depending on the vehicle)

- Clip the lens

12 on to the bulb

- Unclip the lens 12 (using a tool such

holder 13;

as a flat screwdriver), positioned

- clip in the reading spots block 11 until

at C;

the unit clicks;

- unclip and release the bulb

- make sure that the reading spots

holder 13 using the tabs 14;

block is correctly positioned and

- remove the bulb concerned.

locked into place.

Type of bulb 15: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.24

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (4/6)

Glove box light 16

Remove the bulb concerned.

(depending on the vehicle)

Bulb type: W5W.

Unclip light 16 using a flat-blade screw-

driver or similar) by pressing on the

tab 17 to move the light towards the

inside of the unit.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.25

CarManuals2.co

INTERIOR LIGHTING: changing bulbs (5/6)

Luggage compartment

Release the lens 20 and access the

bulb 21.

light 18

Type of bulb 21: W5W.

Unclip light 18 (using a flat-blade screw-

driver or similar), by pressing on tab 19

to move the light towards the inside of

the luggage compartment.

Remove the bulb concerned.

Type of bulb: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.26

CarManuals2.co

REMOTE CONTROL KEY: BATTERY: battery (1/2)

Replacing the battery

Note: It is not advisable to touch the

electronic circuit in the key cover when

Open the case at slot 1 using a flat-

replacing the battery.

blade screwdriver or similar, and re-

place the battery 2, observing the type

When refitting, ensure that the cover is

and polarity shown on the back of the

correctly clipped on and the screw tight-

cover.

ened.

If they need to be replaced,

be sure to use the same

The batteries are available from ap-

or equivalent type of bat-

proved Dealers, and their service

tery (consult an Approved

life approximately two years.

Dealer).

Check that there is no dye on the

battery: risk of an incorrect electri-

cal contact.

5.28

CarManuals2.co

REMOTE CONTROL KEY: BATTERY: battery (2/2)

Operating faults

If the battery is too weak to ensure cor-

rect operation, you will still be able to

start and lock/unlock the vehicle

➥ 1.50.

Do not throw away your used bat-

Precautions relating to

teries; give them to an organisation

batteries:

responsible for collecting and recy-

- keep (new or used) bat-

cling batteries.

teries out of reach of chil-

dren;

- do not swallow batteries;

When replacing:

Risk of chemical burns which

- make sure that the batter-

may lead to death.

ies are correctly inserted.

- if ingested or inserted into any

part of the body, consult a doctor

Risk of explosion.

as soon as possible.

- if the flap does not close cor-

rectly, do not use and keep out of

reach of children.

5.29

CarManuals2.co

“HANDS-FREE” CARD: battery (1/2)

The batteries are available from ap-

proved Dealers, and their service

life approximately two years. Check

that there is no dye on the battery:

risk of an incorrect electrical con-

tact.

If they need to be replaced,

Replacing the battery

When refitting, proceed in the reverse

be sure to use the same

order, then press one of the buttons on

When the message “Keycard Battery

or equivalent type of bat-

the card four times, close to the vehicle:

Low” appears on the instrument panel,

tery (consult an Approved

the next time the vehicle is started, the

replace the battery in the card:

Dealer).

message will disappear.

- slide the rear casing 1 downwards

while pressing on zone A;

Check that the cover is clipped shut.

- remove the battery cover 2;

Note: Do not touch the electronic circuit

- remove the battery by pressing on

or contacts on the card when replacing

one side and lifting the other;

the battery.

When replacing:

- replace it according to the direc-

tion and template shown inside the

- make sure that the batter-

cover.

ies are correctly inserted.

Risk of explosion.

- if the flap does not close cor-

rectly, do not use and keep out of

reach of children.

5.30

CarManuals2.co

“HANDS-FREE” CARD: battery (2/2)

Operating faults

If the battery is too weak to ensure cor-

rect operation, you will still be able to

start and lock/unlock the vehicle

➥ 1.50.

Precautions relating to

batteries:

- keep (new or used) bat-

teries out of reach of chil-

dren;

- do not swallow batteries;

Risk of chemical burns which

may lead to death.

- if ingested or inserted into any

part of the body, consult a doctor

as soon as possible.

Do not throw away your used bat-

teries; give them to an organisation

responsible for collecting and recy-

cling batteries.

5.31

CarManuals2.co

FITTING A RADIO

In all cases, it is very important to

follow the manufacturer’s instruc-

tions carefully.

The specifications of the brack-

Radio location 1

Front door speakers 2

ets and wires (available from our

Unclip the blanking cover. The connec-

To install any equipment, please con-

network) vary depending on the

tions: ( + aerial) and ( - supply and

sult an authorised dealer.

equipment level of your vehicle

speaker) are located behind it.

and the type of radio.

Consult an approved Dealer to

find out the correct part number.

No work may be carried out on

the vehicle’s electrical or radio

circuits, except by approved

dealers: an incorrectly connected

system may result in damage

being caused to the electrical

equipment and/or the compo-

nents connected to it.

5.32

CarManuals2.co

ACCESSORIES

Electrical and electronic accessories

Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po-

sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.

Before connecting an accessory to a socket, please ensure that you do not exceed the maximum power authorised for

the socket. ➥ 3.33, ➥ 3.17. Fire hazard.

No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected

system may result in damage being caused to the electrical equipment and/or the components connected to it.

If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.

Establish the rating and position of this fuse.

Using the diagnostic socket

The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems.

For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved

Dealer. Serious accident risk.

Fitting aftermarket accessories

If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of

your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your

vehicle, which are the only accessories for which the manufacturer will provide a warranty.

If you are using an anti-theft device, only attach it to the brake pedal.

Obstructions to the driver

On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting reg-

ularly. Do not lay one mat on top of another. There is a risk of wedging the pedals.

5.33

CarManuals2.co

FUSES (1/3)

To comply with current legislation, or

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

Fuse boxes

Tweezers 3

bulbs and fuses.

If any electrical component does not

Remove the fuse using the tweezers 3

work, check the condition of the fuses.

on the back of the flap.

To remove the fuse from the tweezers,

Fuses in the passenger compart-

slide the fuse to the side.

ment A

Check the fuse in question

It is not advisable to use the free fuse

and replace it, if neces-

Place your hand in location 2 and pull to

locations.

sary, by a fuse of the same

open the flap 1.

rating.

Depending on the vehicle, to identify

If a fuse is fitted with too high a

the fuses, refer to the fuse allocation

rating, it may cause the electrical

label located at the back of the flap 1

circuit to overheat (risk of fire) in the

and shown on the following pages.

event of an item of equipment using

an excessive amount of current.

5.34

CarManuals2.co

FUSES (2/3)

Allocation of fuses

(the presence of certain fuse depends on the vehicle equipment level)

Symbol

Allocation

Windscreen washer

Front headlights

Hazard warning lights

Horn

Towbar socket

Brake lights, passenger compartment central unit

Use the fuse allocation label in the

Screen washer, rear lights

storage compartment to identify the

fuses.

Certain fuses should only be re-

Direction indicators

placed by a qualified professional.

These fuses are not listed on the

label.

Accessories socket

Only change the fuses represented

on the label.

Electric windows



5.35

CarManuals2.co

FUSES (3/3)

The vehicle drive system

in an electric vehicle uses

a direct voltage of approxi-

mately “400 V”.

This system can get hot during

and after switching off the ignition.

Respect warning messages given

on the labels in the vehicle.

Any intervention or modification

on the vehicle’s “400 V” electrical

Fuses in engine compartment B

system (components, cables, con-

nectors, traction battery) is strictly

Some functions are protected by fuses

prohibited.

located in the engine compartment

(unit B).

Risk of serious injury and/or elec-

tric shock which may endanger

However, because of their reduced

life.

accessibility, we advise you to have

your fuses replaced by an approved

The engine cooling fan may also

Dealer.

start at any moment. The 

label in the engine compartment re-

minds you of this.

Risk of injury.

Before

carrying

out

any

action in the engine com-

partment, you must switch

off the ignition.

➥ 2.2 or

➥ 2.3.

5.36

CarManuals2.co

WIPER BLADES: replacement (1/2)

Replacing the windscreen

To refit

wiper blades 2

To refit the wiper blade 2, insert it in its

To replace the wipers, first put them in

housing in the arm 3, then clip it until

the service positionB.

you hear a click. Make sure that the

With the ignition on and the engine

blade is correctly locked in position.

stopped:

To return the blades to lowered posi-

- move the stalk twice in succession 1

Check the condition of the wiper

tion, make sure that the blades are

to position A (single sweep): the

blades. You are responsible for their

folded down onto the windscreen then

wiper blades will stop in the service

service life:

set the 1 stalk to position A (single

position B away from the bonnet;

- clean the blades, windscreen and

sweep): the windscreen wiper blades

- lift the wiper arm 3;

rear screen regularly with soapy

will fold into the bonnet when the igni-

- lower the 4 tab then remove the

water;

tion is switched on.

blade 2.

- do not use them when the wind-

screen or rear screen are dry;

- free them from the windscreen or

rear screen when they have not

been used for a long time.

5.37

CarManuals2.co

WIPER BLADES: replacement (2/2)

- In frosty weather, make

sure that the wiper blades

are not stuck by ice

(to

avoid the risk of the motor

overheating).

- Check the condition of the wiper

blades. Replace the wiper blades

Rear screen wiper blade 5

as soon as they begin to lose ef-

Stalk in stop position (deactivated):

ficiency

(approximately once a

- lift the wiper arm 6;

year).

- turn the blade horizontally 5 (move-

When changing the blade, when it

ment C) until it unclips;

has been removed, do not let the

Check the condition of the wiper

- remove the blade by pulling it.

wiper arm fall against the window:

blades.

risk of breaking the window.

To refit

- clean the blades, windscreen and

rear screen regularly with soapy

To refit the wiper blade, proceed in re-

water;

verse order to removal. Make sure that

the blade is correctly locked in position.

- do not use them when the wind-

screen or rear screen are dry;

Before changing the rear

wiper blade, make sure the

- free them from the windscreen or

stalk is in the stop position

rear screen when they have not

(deactivated).

been used for a long time.

Risk of injury.

5.38

CarManuals2.co

TOWING: breakdown (1/2)

Before any towing, including on a flat-

bed truck, put the gear control in N po-

sition, unlock the steering column and

release the parking brake.

The speed specified by current legis-

lation for towing must always be ob-

served.

If you are driving the towing vehicle,

do not exceed the permissible towing

weight for your vehicle ➥ 6.7.

To carry out breakdown recovery on

a flatbed or to tow the vehicle using a

towing point (see the next page), ob-

serve the following instructions:

Insert the key into the ignition and set

to “On” “ON” position 2 or, depend-

Depending on the vehicle, after un-

Choice of towing

ing on the vehicle, with the card in

locking the steering column, press

the passenger compartment, press

It is strictly forbidden to tow the vehicle

the engine start button for approxi-

the start button;

with the front wheels on the ground.

mately two seconds;

Set the gear control to N position;

Depending on the vehicle, once you

–

The steering column unlocks. The

have finished towing, press and hold

accessories functions are supplied:

the engine start button for approxi-

you can use the vehicle lighting func-

mately two seconds (risk of running

tions (hazard warning lights, brake

down the battery).

lights, etc.). At night the vehicle lights

must be on;

Do not leave the tools unsecured inside the vehicle as they may come

loose under braking. After use, ensure that the tools are correctly placed

in their support, positioned correctly in their housing, attach the strap,

then make sure that the tool kit access flap is properly locked.

Risk of injury.

5.39

CarManuals2.co

TOWING: breakdown (2/2)

Tighten the towing hitch 3 fully: first

by hand until it stops, then finish by

locking it with the wheel brace or, de-

pending on the vehicle, the lever.

Only use the towing hitch 3 and the

wheelbrace or lever provided with the

tools ➥ 5.8.

When the engine is stopped,

steering and braking assist-

ance are not operational.

Only use the front 2 and rear 5 towing

Access to towing points

points (never use the driveshafts or any

other part of the vehicle). These towing

Front towing point 2

- Use a rigid towing bar.

points may only be used for pulling.

Unclip the cover 1 by passing the key

If a rope or cable is used

They must never be used for lifting the

integrated in the card in the notch A.

(where the law allows this),

vehicle directly or indirectly.

the vehicle being towed

Rear towing point 5

must be able to brake.

Unclip the cover 4 by passing the key

A vehicle must not be towed if it is

integrated in the card in the notch B.

not fit to be driven.

Avoid accelerating or braking

suddenly when towing, as this

Do not remove the key

may result in damage being

from the ignition switch, or

caused to the vehicle.

leave the card in the vehicle

In all cases, it is advisable not to

during towing (depending

exceed 15.5 mph (25 km/h).

on the vehicle).

Ensure that the towing eye

Risk of the steering column lock-

is bolted correctly.

ing.

Risk of losing the towed

object.

5.40

CarManuals2.co

OPERATING FAULTS (1/7)

The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact

an approved dealer as soon as possible.

FAULTS

POSSIBLE CAUSES

WHAT TO DO

Impossible to charge the traction bat-

The outdoor temperature is lower

Recharge your vehicle in a more suitable

tery.

than -26°C.

environment. If necessary ➥ 5.39.

The charging flap warning light flashes

red.

No electrical current in the wall

Check your installation (circuit breaker, pro-

socket or poor connection of cable

grammer, etc.).

to domestic socket.

Check the connections (charging socket,

etc.) ➥ 1.9.

The cord is defective.

Please see an authorised dealer to replace

it.

Impossible to charge the traction bat-

The charging cord is not correctly

Plug the charging cable correctly in to the

tery.

locked to the vehicle.

vehicle. ➥ 1.9.

The charging flap warning light flashes

blue.

The programmable air conditioning

One of the usage conditions is not

➥ 3.13.

fails to work.

complied with (the traction battery

is not charged, etc).

5.41

CarManuals2.co

OPERATING FAULTS (2/7)

Using the card

POSSIBLE CAUSES

WHAT TO DO

The card does not lock or

Card battery is flat.

Replace the battery. You will still be able to lock/

unlock the doors.

unlock and start your vehicle ➥ 1.50 and ➥ 2.2

or ➥ 2.3.

Use of appliances operating on the

Stop using the devices or use the key provided

same frequency as the card (mobile

➥ 1.50.

phone, etc.).

Vehicle located in a high electromag-

Use the key that is built into the card

netic radiation zone.

➥ 1.50.

Vehicle battery flat.

The message “Place card on zone +

Place the card in the placement area ➥ 2.3 then

START” appears on the instrument

press the START button.

panel.

The vehicle is started.

While the engine is on, it is not possible to lock/

unlock using the card. Turn off the ignition.

Desynchronisation of the card.

Unlock the driver’s door by inserting the key inte-

grated in the card into the door lock ➥ 1.50 then

place the card in the placement area ➥ 2.3 and

press the START button to synchronise the card.

5.42

CarManuals2.co

OPERATING FAULTS (3/7)

The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact

an approved dealer as soon as possible.

Using the remote control

POSSIBLE CAUSES

ACTION REQUIRED

The remote control does not lock or The remote control battery is flat.

Use the emergency key.

unlock the doors.

Use of appliances operating on the same

Stop using the devices or use the key.

frequency as the remote control (mobile

phone, etc.).

Vehicle located in a high electromagnetic

Replace the battery. You will still be able to

radiation zone.

lock/unlock and start your vehicle. ➥ 1.50

Discharged battery.

and ➥ 2.2 or ➥ 2.3.

The vehicle is started.

While the engine is on, it is not possible

to lock/unlock using the key. Turn off the

ignition.

Desynchronisation of the remote control

Unlock the driver’s door by inserting the

key into the door lock ➥ 1.50, then start

the engine to synchronise the remote con-

trol ➥ 2.3.

5.43

CarManuals2.co

OPERATING FAULTS (4/7)

The starter is activated

POSSIBLE CAUSES

ACTION REQUIRED

The engine will not start.

Starting conditions are not ful- ➥ 2.2 or ➥ 2.3.

filled.

The “hands-free” card does not Place the card in the recess provided for this purpose

work.

on the centre console ➥ 2.2 or ➥ 2.3.

The engine cannot be switched off.

Card not detected.

Place the card in the recess provided for this purpose

on the centre console.

Press and hold the start button.

Electronic fault.

Press the start button 3 times quickly or press and

hold.

The steering column remains locked. Steering wheel locked.

Move the steering wheel while pressing the engine

start button (or, depending on the vehicle, operating

the ignition key) ➥ 2.2.

Faulty electrical circuit.

Consult an approved dealer.

Steering becomes heavy.

Assistance overheating.

Drive carefully at reduced speed, be aware of the

level of force in the steering wheel needed to turn the

wheels.

Fault with the electric assis-

Consult an authorised dealer.

tance motor. Fault in the assis-

tance system.

Vibrations.

Tyres not inflated to correct

Check the tyre pressures: if this is not the problem,

pressures, incorrectly balanced

have them checked by an approved Dealer.

or damaged.

5.44

CarManuals2.co

OPERATING FAULTS (5/7)

On the road

POSSIBLE CAUSES

WHAT TO DO

The engine is overheating. The

Engine cooling fan not working.

Stop the vehicle, switch off the engine and

coolant temperature indicator is in

contact an approved dealer.

the warning zone and warning light

comes on.

Coolant leaks.

Check the coolant reservoir: it should con-

tain fluid. If there is no coolant, consult an

authorised dealer as soon as possible.

Coolant boiling in the coolant reser-

Mechanical fault: damaged cylinder

Stop the engine.

voir.

head gasket.

Contact an approved dealer.

The engine cooling fan starts to run

This is not necessarily a fault. The

after the ignition is switched off.

engine cooling fan group may start

to run in order to regulate the engine

temperature. This operation may last

several minutes after the engine is

switched off.

The engine cooling fan runs for more

Consult an approved dealer.

than 10 minutes after the engine is

switched off.

Radiator: if there is a significant lack of coolant, remember that it must never be topped up using cold coolant when the

engine is very hot. After any procedure on the vehicle which has involved even partial draining of the cooling system,

it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved by our

Technical Department may be used for this purpose.

5.45

CarManuals2.co

OPERATING FAULTS (6/7)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

The wipers do not work.

Wiper blades stuck.

Free the blades before using the wipers.

Faulty electrical circuit.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.34.

The wiper does not stop.

Faulty electrical controls.

Consult an approved dealer.

Direction indicators flashing more

Blown rear bulb.

➥ 5.18.➥ 1.50

quickly.

The direction indicators do not work.

Faulty electrical circuit or control.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.34.

The lights do not come on or go off.

Faulty electrical circuit or control.

Consult an approved dealer.

Fuse damaged.

Replace the fuse or have it replaced

➥ 5.34.

5.46

CarManuals2.co

OPERATING FAULTS (7/7)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

Traces of condensation in the head-

Traces of condensation may be a nat-

lights or rear lights.

ural phenomenon caused by varia-

tions in temperature and humidity.

In this case, the traces will disappear

slowly once the lights are switched

on.

The front seat belt reminder light

An object is stuck between the floor

Remove all objects from underneath the

comes on when the seat belts are

and the seat and is disrupting the op-

front seats.

fastened.

eration of the sensor.

5.47

CarManuals2.co

VEHICLE IDENTIFICATION PLATES

The information shown on the ve-

MMAC (Maximum permissible

hicle identification plate should be

all-up weight).

quoted on all correspondence or

MTR (Gross train weight: vehicle

orders.

fully loaded, with trailer).

MMTA (Maximum Permissible

The presence and location of the in-

Weight) front axle.

formation depends on the vehicle.

MMTA rear axle.

Reserved for related or additional

Vehicle identification plate A

entries.

Manufacturer name.

Paint reference (colour code).

EC design number or approval

number.

Identification number.

Depending on the vehicle, this

information is also given on

marking B.

6.2

CarManuals2.co

TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES

The QR Code on the A label allows

Ensure that the A label is always visible

emergency workers using a tablet or

and present on the windscreen as well

smartphone to immediately access the

as the rear screen.

technical information useful for working

Any modification or damage would

on the vehicle in the event of an acci-

prevent access to the information.

dent.

Note: vehicles without rear windows

have only the front label affixed.

6.3

CarManuals2.co

DIMENSIONS (in metres) (2/2)

“Standard chassis”

“Long chassis”

0,962

2,716

3,100

0,810

0,848

4,487

4,910

Door mirrors folded in

1,919

Door mirrors folded out

2,159

1,580

1,600

Estate version

1,810

H (unladen)

Van version

1,830

Turning circles between kerbs

10,9

12,4

Turning circles between walls

11,2

13,1

Caution: if the vehicle is fitted with roof bars, the height must be increased by 0,052 m (the bars cannot be removed).

6.6

CarManuals2.co

WEIGHTS (in kg)

The weights indicated for a basic vehicle without options: they vary depending on your vehicle’s equipment. Consult

your approved Dealer.

Van version

Estate versions

Versions

Standard chassis

Long chassis

Standard chassis

Maximum Authorised Mass (MMAC)

Maximum permissible weight (MMTA)

Weights indicated on the vehicle identification plate ➥ 6.2

Gross Train Weight (MTR)

Braked Trailer Weight*

found by calculating: MTR - MMAC

Unbraked Trailer Weight*

750 kg

Permissible nose weight*

75 kg

Maximum permissible load on roof

➥ 3.47, ➥ 3.49

* Towing weight (Towing a caravan, boat, etc.)

Towing is prohibited when the MTR-MMAC calculation is equal to zero, or when the MTR is equal to zero (or is not listed) on the

identification plate.

- It is important to respect local towing regulations in force, specifically those set out in the Highway Code. Please contact your

authorised dealer about adapting any towing equipment.

- When towing, under no circumstances may the total train weight (vehicle + trailer) be exceeded. However the following is

permitted:

- rear axle MMTA exceeded by no more than 15%,

- maximum MMAC exceeded by no more than 10% or 100 kg (whichever is reached first).

In either case, the maximum speed of the vehicle and trailer must not exceed 48 mph (80 km/h) (van versions) or 60 mph

(100 km/h) (estate versions) and the tyre pressure must be increased by 0.2 bar (3 PSI).

- The engine output and climbing capability are reduced with altitude. We recommend that the maximum load be reduced by 10%

at an altitude of 1,000 metres and by an additional 10% for each 1,000 metres thereafter.

6.7

CarManuals2.co

REPLACEMENT PARTS AND REPAIRS

Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same

level of quality as the parts fitted originally.

If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out

within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the

repair order.

6.8

CarManuals2.co

SERVICE SHEETS (1/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.9

CarManuals2.co

SERVICE SHEETS (2/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.10

CarManuals2.co

SERVICE SHEETS (3/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.11

CarManuals2.co

SERVICE SHEETS (4/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.12

CarManuals2.co

SERVICE SHEETS (5/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.13

CarManuals2.co

SERVICE SHEETS (6/6)

VIN:

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

Date:

Miles (Km):

Invoice number:

Comments/miscellaneous

Type of operation:

Stamp

Service

□

Anti-corrosion check:

OK □ Not OK* □

*See specific page

6.14

CarManuals2.co

Renault Kangoo E-Tech (2023 year). Manual in english - page 9