Renault Kangoo (2023 year). Manual in english - page 1

 

  Index      Manuals     Renault Kangoo (2023 year). Manual in english

 

Search            copyright infringement  

    

 

   

 

   

 

Content      ..      1       2         ..

 

 

 

Renault Kangoo (2023 year). Manual in english - page 1

 

 

C O N T E N T S
Sections
Getting to know your vehicle
1
Driving
2
Your comfort
3
Maintenance
4
Practical advice
5
Technical specifications
6
Alphabetical index
7
0.11
CarManuals2.co
Section 1: Getting to know your vehicle
Key, radio frequency remote control: general information, use, deadlocking
1.2
Card: general information, use, deadlocking
1.7
Opening and closing the doors
1.23
Locking, unlocking the opening elements
1.29
Automatic locking when driving
1.32
Headrests, front seats
1.33
Seat belts
1.43
Additional methods of restraint
1.50
at the front, rear seat belts
1.50
side
1.57
Child safety: general information
1.59
choosing a child seat mounting
1.62
fitting a child seat, general information
1.65
Child seats: attachment by seat belt or by isofix system. .
1.67
deactivating, activating the front passenger airbag.
1.90
Audible and visual signals
1.93
Driving position
1.94
Instrument panel
1.98
displays and indicators
1.103
trip computer
1.109
vehicle settings customisation menu
1.119
Clock and outdoor temperature
1.122
Steering wheel, Power-assisted steering
1.124
Rear view mirrors
1.125
Camera rear view
1.129
Exterior lighting and signals
1.133
Headlight beam adjustment
1.139
Washers, wipers
1.141
Fuel tank (filling with fuel)
1.147
Reagent tank
1.150
1.1
CarManuals2.co
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2)
4 Locking/unlocking using the switch-
A
B
blade key. To release the insert from
its housing, press button 4, it comes
3
out automatically. Press button 4 and
3
guide the insert back into its housing.
4
4
7 Unlocking the sliding side doors and
2
the rear hinged doors.
1
1
6
5
7
Depending on the vehicle, there are
Key, Remote control B
two types of keys, key A or key B.
1
Locks all the opening elements.
Key, Remote control A
6
Unlocking all the opening elements,
1 Locks all the opening elements.
in Access mode, or unlocking the
2 Unlocks all the opening elements.
front doors, in Secure mode.
3 Driver’s door and ignition key.
3
Driver’s door and ignition key.
4 Locking/unlocking using the switch-
Remote control B
blade key. To release the insert from
There are two ways to use the
its housing, press button 4, it comes
remote control: Access mode and
out automatically. Press button 4 and
Secure mode.
guide the insert back into its housing.
To switch between the remote con-
5 Unlocking/locking the luggage com-
trol user modes, use the “Access”
partment only.
menu from the trip computer or,
depending on the vehicle, from
the multimedia screen. The default
mode is Access mode.
1.2
CarManuals2.co
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2)
Radio frequency remote control
operating range
This varies according to the surround-
ings: take care not to lock or unlock the
Replacement and additional keys
doors by inadvertently pressing the but-
or remote controls.
tons on the remote control.
You must only contact an approved
dealer:
Driver’s responsibility
Note: if any opening element (door or
- If you need to replace a key it will
when parking or stopping
luggage compartment) is open or not
be necessary to take the vehicle
the vehicle
properly shut, locking is unsuccessful
and all of its keys to an approved
and the hazard warning lights and side
Never leave an animal,
Dealer in order to initialise the
indicator lights do not flash.
child or adult who is not self-suffi-
system.
cient alone on your vehicle, even for
Interference
- Depending on the vehicle, you
a short time.
Interference by factors in the immediate
have the option of using up to
vicinity (external installations or the use
four remote controls.
They may pose a risk to themselves
of equipment operating on the same
or to others by starting the engine,
Remote control unit failure
activating equipment such as the
frequency as the remote control) may
Make sure that the correct battery
electric windows or locking the
affect the operation of the remote con-
type is being used, and that the
doors.
trol.
battery is in good condition and in-
Also, in hot and/or sunny weather,
serted correctly. These batteries
please remember that the tempera-
have a service life of approximately
ture inside the passenger compart-
two years.
ment increases very quickly.
How to change the battery ➥ 5.27.
RISK OF DEATH OR SERIOUS
INJURY.
The key must not be used for any
Advice
function other than those described
Avoid leaving the remote control in
in the handbook (removing the cap
hot, cold or humid areas.
from a bottle, etc.).
1.3
CarManuals2.co
RADIO FREQUENCY REMOTE CONTROL: use (1/2)
Remote control A or, depending on the
Remote control A
vehicle, remote control B locks or un-
Press button 2 to unlock all the opening
locks the doors. It is powered by a bat-
elements.
tery which can be replaced. ➥ 5.27.
Remote control B
2
Press button 4 once to:
Locking the doors
- unlock all the opening elements, in
1
Access mode;
Press locking button 1.
4
- unlock the front doors, in Secure
The hazard lights and side repeaters
1
mode.
flash twice to indicate that the doors
have locked and, on some vehicles,
the door mirrors fold in automatically.
3
A
Note: if any opening element (door or
5
luggage compartment) is open or not
B
properly shut, locking is unsuccessful
and the hazard warning lights and side
Unlocking the rear area
indicator lights do not flash.
Using the remote control B,
press
button 5 to unlock the sliding side doors
Unlocking/locking the
and the rear hinged doors.
luggage compartment only
Using the remote control A, press
Unlocking the doors
Remote control B
button 3 to unlock/lock the luggage
The hazard lights and side repeaters
compartment door only.
flash once to indicate that the doors
There are two ways to use the
have unlocked and, on some vehicles,
remote control: Access mode and
the door mirrors fold out automatically.
Secure mode.
To switch between the remote con-
trol user modes, use the “Access”
menu from the trip computer or,
depending on the vehicle, from
the multimedia screen. The default
mode is Access mode.
1.4
CarManuals2.co
RADIO FREQUENCY REMOTE CONTROL: use (2/2)
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.
Also, in hot and/or sunny weather,
While the engine is running, the
please remember that the tempera-
buttons on remote control A or, de-
ture inside the passenger compart-
pending on the vehicle, on remote
ment increases very quickly.
control B are inactive.
RISK OF DEATH OR SERIOUS
INJURY.
Depending on the vehicle, the door
mirrors fold in/out automatically
when the vehicle is locked/unlocked
➥ 1.125.
1.5
CarManuals2.co
RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking
If the vehicle is equipped with a dead-
locking function, this allows you to lock
the opening elements and to prevent
the doors from being unlocked using
the interior handles (for example, by
breaking the window and then trying to
open the door from the inside).
1
To do this, press button 1 twice in quick
succession.
The hazard warning lights and side in-
dicator lights give two slow flashes and
three quick flashes to indicate locking.
Depending on the vehicle, the door mir-
rors fold in automatically when the vehi-
cle is locked ➥ 1.125.
Never use deadlocking if
someone is still inside the
vehicle.
1.6
CarManuals2.co
CARD: general information (1/4)
A
B
1
5
4
4
2
2
3
6
Depending on the vehicle, there are
B card
two types of cards, card A or card B.
4
Switching on the lighting remotely.
5
Unlocking all the front doors in
A card
Secure mode, or unlocking all the
1 Unlocking the doors and tailgate.
opening elements in Access mode.
2 Locking all doors and tailgate.
2
Locks all the opening elements.
3 Unlocking/locking the luggage com-
6
Unlocking the rear area (sliding side
B card
partment only or, depending on the
doors and rear hinged doors).
There are two ways to use the card:
vehicle, unlocking the rear area
Access mode and Secure mode.
(sliding side doors and rear hinged
doors).
To switch between the card user
modes, use the “Access” menu from
4 Switching on the lighting remotely.
the trip computer or, depending on
the vehicle, from the multimedia
screen. The default mode is Secure
mode.
1.7
CarManuals2.co
CARD: general information (2/4)
The card is used for:
card operating range
Battery life
- locking/unlocking the doors and tail-
This varies according to the environ-
Make sure that the correct battery type
gate (doors, tailgate) and the fuel
ment: take care not to accidentally lock
is being used, and that the battery is in
filler flap (see the following pages);
or unlock the vehicle by inadvertently
good condition and inserted correctly.
pressing the buttons on the card.
Its service life is approximately two
- switching on the vehicle lighting re-
years: it should be replaced when the
motely (refer to the following pages).
Note: if a door or the boot is open or not
message “Keycard Battery Low” ap-
properly shut, locking is not carried out.
pears on the instrument panel ➥ 5.29.
A beep sounds and the hazard warning
lights and side repeaters do not flash.
Interference
Interference by factors in the immediate
vicinity (external installations or the use
of equipment operating on the same
frequency as the card) may disrupt its
operation.
Advice
Avoid leaving the card in hot, cold or
humid areas.
Keep the card with you.
Do not keep the card in a place
where it could be bent or dam-
aged accidentally, such as in a back
pocket of a garment.
When the battery is flat, you can still
lock/unlock and start your vehicle.
➥ 1.29 ➥ 2.5.
1.8
CarManuals2.co
CARD: general information (3/4)
4
4
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone in your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
Distance lighting function
activating equipment such as the
Press button 4 once to switch on the ex-
electric windows or locking the
terior lighting for approximately 20 sec-
doors, for example.
onds. This can be used, for example,
Replacement: need for an
Also, in hot and/or sunny weather,
to identify the vehicle from a distance
additional card
please remember that the tempera-
when parked in a car park.
ture inside the passenger compart-
If you lose your card or require an-
Pressing and holding the 4 button for
ment increases very quickly.
other, you can obtain one from an
approximately two seconds activates
authorised dealer.
RISK OF DEATH OR SERIOUS
the exterior lighting and a sound is
INJURY.
If a card is replaced, it will be neces-
emitted.
sary to take the vehicle and all its
Note: pressing button 4 again switches
cards to an approved Dealer to ini-
off the lighting.
tialise the system.
You may use up to four cards per
vehicle.
1.9
CarManuals2.co
CARD: general information (4/4)
7
C
9
10
8
Fitting a strap 9
Insert the hand strap into the 10 com-
ponent and pass the end of the strap
Slide the rear casing
7 downwards
through the buckle.
while pressing on zone C.
Position the hand strap at the open-
ing 8 and close the cartridge.
Note: check that the diameter of the
strap cord 9 will fit the opening 8.
Never insert screwdriver-type tools
into the 8 opening.
1.10
CarManuals2.co
“HANDS-FREE” CARD: use (1/11)
A card
There are three ways to unlock/lock the
A
vehicle:
- “hands-free”, when approaching and
moving away from the vehicle;
- in “hands free” mode, depending on
the vehicle, using button 2 on the
1
door handle 1;
- using the card in remote control
mode.
Deactivating/activating the «hands-
2
free» mode
Depending on the vehicle, from the trip
computer or the multimedia screen you
can deactivate/activate the following:
- unlocking when approaching the ve-
hicle;
- locking when moving away from the
vehicle;
Driver’s responsibility when parking or stopping the vehicle
- the “hands-free” locking and unlock-
Never leave an animal, child or adult who is not self-sufficient alone in
ing completely.
your vehicle, even for a short time.
You can also disable/activate the
They may pose a risk to themselves or to others by starting the engine,
sound signal that is emitted upon lock-
activating equipment such as the electric windows or locking the doors, for ex-
ing when moving away from the vehi-
ample.
cle ➥ 1.119.
Also, in hot and/or sunny weather, please remember that the temperature inside
the passenger compartment increases very quickly.
RISK OF DEATH OR SERIOUS INJURY.
Never leave your vehicle
with the card inside.
1.11
CarManuals2.co
“HANDS-FREE” CARD: use (2/11)
5
3
4
Hands-free unlocking, when
Hands-free locking when moving
The vehicle cannot be remotely locked
approaching the vehicle;
away from the vehicle
if the card is within the area 5.
With the card in access zone 3, the ve-
With the card on you, doors and lug-
hicle will unlock. Unlocking is indicated
gage compartment door closed, move
by one flash of the hazard warning
away from the vehicle: it will lock auto-
lights and the indicator lights.
matically once you have left the access
zone 4.
Note: the distance at which the vehicle
locks depends on the surroundings.
To indicate that the vehicle has been
locked, the hazard warning lights
flash twice and then light up for ap-
proximately four seconds, and a beep
Depending on the vehicle, the door
sounds in confirmation.
mirrors fold in/out automatically
when the vehicle is locked/unlocked
➥ 1.125.
1.12
CarManuals2.co
“HANDS-FREE” CARD: use (3/11)
A
1
6
3
2
If the card has been within the detection
“Hands-free” unlocking/locking
With the vehicle unlocked, press
area 4 for approximately 15 minutes,
using button 2
button 2 once to lock the vehicle.
remote locking is disabled.
(depending on the vehicle)
The hazard warning lights flash twice
To lock the vehicle, press the 6 button
With the card in zone 3 and the vehi-
to indicate that the vehicle is locked
on the card or, depending on the vehi-
cle locked, press button 2 on the door
and, depending on the vehicle, the door
cle, press the 2 button on the handle 1.
handle 1 to unlock the vehicle.
mirrors automatically fold in.
Pressing the tailgate button once un-
locks the entire vehicle and opens the
tailgate.
The hazard lights and side repeaters
flash once to indicate that the doors
have unlocked and, on some vehicles,
Do not store the card anywhere it
the door mirrors fold out automatically.
may come into contact with other
electronic equipment
(computer,
phone etc.) as this could hinder its
operation.
1.13
CarManuals2.co
“HANDS-FREE” CARD: use (4/11)
Special features relating to “hands-
free” locking
After locking in “hands-free” mode, you
have to wait approximately three sec-
onds before being able to unlock the
vehicle again. During these three sec-
onds, the door handles can be tried to
1
make sure that the vehicle is locked
properly.
Note: if a door or the boot is open or not
properly shut, locking is not carried out.
2
A beep sounds and the hazard warning
lights and side repeaters do not flash.
Special features of the unlocking
system
After eight days of non-use, approach
unlocking is disabled.
Use the card in remote control mode
(see following pages) or, depending on
the vehicle, press the 2 button (on front
door handle) to unlock the vehicle and
reactivate “hands-free” mode.
1.14
CarManuals2.co
“HANDS-FREE” CARD: use (5/11)
Locking using the card
A
With the doors and boot closed, press
button 6: the vehicle locks.
7
The hazard warning lights flash twice
to indicate that the vehicle is locked
and, depending on the vehicle, the door
6
mirrors automatically fold in.
Note:
8
5
- the maximum distance at which the
vehicle locks depends on the sur-
roundings;
- if a door or the boot is open or not
properly shut, locking is not carried
out. A beep sounds and the hazard
Using the card as a remote
warning lights and side repeaters do
If, while the engine is running, a door
not flash.
is opened and closed, and the card is
control A
no longer in the zone 5, the message
Unlocking with the card
Keycard Not Detected indicates that
Unlocking/locking the boot
the card is not inside the vehicle. This
Press button 7.
only or, depending on the
will, for example, prevent you from driv-
The hazard lights and side repeaters
vehicle, unlocking the rear
ing away after dropping off a passenger
flash once to indicate that the doors
area
who has kept the card on them.
have unlocked and, on some vehicles,
the door mirrors fold out automatically.
Press the 8 button to unlock/lock the
The warning disappears when the card
boot only or, depending on the vehicle,
is detected again.
to unlock the rear area.
The card buttons are deactivated
when the engine is running.
1.15
CarManuals2.co
“HANDS-FREE” CARD: use (6/11)
B card
B
Unlocking the vehicle
There are two ways to unlock the ve-
hicle:
- in “hands-free” mode, using the but-
tons on the door handles;
- using the card in remote control
mode.
Locking the vehicle
There are four ways to lock the vehicle:
9
- in “hands-free” mode, when moving
away from the vehicle;
10
- in
“hands-free” mode, using the
button 9 on one of the front door han-
dles;
- in
“hands-free” mode, using the
Deactivating/activating the «hands-
button 10 on the handle of one of
free» mode
the sliding side doors or using the
Depending on the vehicle, from the trip
button 11 on the rear hinged door;
computer or the multimedia screen you
- using the card in remote control
can deactivate/activate the following:
mode.
- locking when moving away from the
vehicle;
- locking and unlocking by pressing
button 9 on one of the front door han-
dles.
You can also disable/activate the
sound signal that is emitted upon lock-
ing when moving away from the vehi-
Do not store the card anywhere it
cle ➥ 1.119.
11
may come into contact with other
electronic equipment
(computer,
phone etc.) as this could hinder its
operation.
1.16
CarManuals2.co
“HANDS-FREE” CARD: use (7/11)
12
12
11
9
10
12
“Hands-free” unlocking
The hazard lights and side repeaters
Note: “hands-free” unlocking will not
flash once to indicate that the doors
work if the card is not present within
With the card in the access zone 12:
have unlocked and, on some vehicles,
the detection zone 12 of the button
- press the 9 button on the handle of
the door mirrors fold out automatically.
pressed.
one of the front doors to unlock the
front doors in secure mode, or all the
opening elements in access mode;
- press the 10 button on the handle of
one of the sliding side doors or, on
the 11 button of the rear hinged door
to unlock the rear area in secure
mode or all the opening elements in
access mode.
1.17
CarManuals2.co
“HANDS-FREE” CARD: use (8/11)
12
12
11
9
10
12
“Hands-free” locking
Secure mode
The hazard warning lights flash twice
to indicate that the vehicle is locked
With the vehicle unlocked, all the open-
If one of the front doors is open, press
and, depending on the vehicle, the door
ing elements closed, press button 9, 10
the 9, 10 or 11 button to lock the rear
mirrors automatically fold in.
or 11 once to lock all the opening ele-
area.
ments.
Note: “hands-free” locking will not work
If one of the opening elements in the
if the card is not present within the de-
rear area is open, press the 9, 10 or 11
tection zone 12 of the button pressed.
button to lock the front doors.
Special features relating to “hands-
Access mode
free” locking
If a door or the boot is open or not prop-
After locking in hands-free mode, you
erly shut, locking using the 9, 10 or 11
have to wait approximately three sec-
button is not carried out.
onds before being able to unlock the
vehicle again.
1.18
CarManuals2.co
“HANDS-FREE” CARD: use (9/11)
14
13
15
Hands-free locking when moving
If the card has been within the detection
The vehicle cannot be remotely locked
away from the vehicle
area 13 for approximately 15 minutes,
if the card is within the area 15.
remote locking is disabled. To lock the
With the card on you, doors and lug-
Note: if an opening element is open or
vehicle, press button 14 on the card.
gage compartment door closed, move
not properly shut, “hands-free” locking
away from the vehicle: it will lock auto-
when moving away from the vehicle
matically once you have left the access
is not carried out. The hazard warning
zone 13.
lights and indicator lights do not flash.
Note: the distance at which the vehicle
locks depends on the surroundings.
To indicate that the vehicle has been
locked, the hazard warning lights
flash twice and then light up for ap-
proximately four seconds, and a beep
sounds in confirmation.
1.19
CarManuals2.co
“HANDS-FREE” CARD: use (10/11)
Unlocking with the card
Locking using the card
B
Press button 16 to unlock the sliding
With all the opening elements closed,
side doors and the rear hinged doors.
press the 14 button: the vehicle locks.
17
The hazard warning lights flash twice
Secure mode
to indicate that the vehicle is locked
Press button 17 to unlock the front
and, depending on the vehicle, the door
14
doors.
mirrors automatically fold in.
Access mode
Note:
16
Press button 17 to unlock all the open-
- the maximum distance at which the
ing elements.
vehicle locks depends on the sur-
roundings;
The hazard lights and side repeaters
flash once to indicate that the doors
- if a door or the boot is open or not
have unlocked and, on some vehicles,
properly shut, locking using the 14
the door mirrors fold out automatically.
button is not carried out. A beep
Using the card as a remote
sounds and the hazard warning lights
and side repeaters do not flash.
control B
There are two modes of use: Secure
mode and Access mode.
To switch between the card user
modes, use the “Access” menu from
the trip computer or, depending on the
vehicle, from the multimedia screen.
The default mode is Secure mode.
The card buttons are deactivated
when the engine is running.
1.20
CarManuals2.co
“HANDS-FREE” CARD: use (11/11)
18
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone in your vehicle, even for
a short time.
If, while the engine is running, a door
They may pose a risk to themselves
is opened and closed, and the card is
or to others by starting the engine,
no longer in the zone 18, the message
activating equipment such as the
“Keycard Not Detected” indicates that
electric windows or locking the
the card is not inside the vehicle. This
doors, for example.
will, for example, prevent you from driv-
Also, in hot and/or sunny weather,
ing away after dropping off a passenger
please remember that the tempera-
who has kept the card on them.
ture inside the passenger compart-
The warning disappears when the card
ment increases very quickly.
is detected again.
RISK OF DEATH OR SERIOUS
INJURY.
Never leave your vehicle
with the card inside.
1.21
CarManuals2.co
“HANDS-FREE” CARD: DEADLOCKING
If the vehicle is equipped with a dead-
To activate deadlocking
1
locking function, this allows you to lock
2
Press button 2 twice in quick succes-
the opening elements and to prevent
sion.
the doors from being unlocked using
the interior handles (for example, by
Locking is confirmed by two slow
breaking the window and then trying to
flashes and three quick flashes of
open the door from the inside).
the hazard warning lights and indicator
lights.
Depending on the vehicle, the door mir-
rors fold in automatically when the vehi-
cle is locked ➥ 1.125.
To deactivate deadlocking
Press the 1 button.
The hazard warning lights flash once
to indicate that the doors have been un-
locked.
1
2
Never use deadlocking if
someone is still inside the
vehicle.
1.22
CarManuals2.co
OPENING AND CLOSING THE DOORS (1/6)
Door/tailgate open buzzer
When the vehicle is stationary, the
2
warning light appears on the instrument
2
panel accompanied by a warning light
indicating which of the opening ele-
ments (door(s), luggage compartment)
are open or incorrectly closed.
Once the vehicle reaches a speed
of approximately 6 mph (10 km/h), a
1
warning light indicates if the door(s)
or luggage compartment are open
or not properly closed, along with the
message “WARNING: Boot Open” or
“WARNING: Door Open” and a beep
will sound for around 40 seconds or
Front doors
Opening from the inside
until the door/luggage compartment is
Unlock the door and pull handle 2.
closed.
Opening from the outside
With the doors unlocked or, depending
on the vehicle, the card on you, hold the
Lights-on reminder buzzer
handle 1 and pull it towards you.
If you have switched off the ignition
and left the lights switched on, a re-
minder buzzer will sound when a door
is opened.
Special note
Depending on the vehicle, accessories
(e.g. radio) stop working either when
As a safety precaution,
the engine is switched off or when the
the doors should only be
doors are locked, or when the driver’s
opened or closed when the
door is opened.
vehicle is stationary.
1.23
CarManuals2.co
OPENING AND CLOSING THE DOORS (2/6)
Recommendations con-
cerning the sliding side
door
The following precautions
A
must be taken when opening and
closing the doors or any other open-
ing element:
4
-
Check that nobody, no animal or
object is at risk of being harmed
when you perform this manoeu-
B
vre.
3
-
Never use anything but the han-
dles on the inside and outside of
the door to operate it.
Sliding side door
Child safety
-
Take care when both opening
(depending on the vehicle)
and closing the door.
Opening the doors from the outside
To make it impossible for the sliding side
Unlock the door and pull handle 3,
-
Caution: when the vehicle is
doors to be opened from the inside, use
then slide the door towards the rear of
parked on a slope, open the door
the key to turn the lock 4 (position B)
the vehicle until it locks in position. To
with care until it is fully open and
and close the door.
unlock the doors ➥ 1.4 ➥ 1.11.
latches into its locking position;
Check from the inside that all the
-
Before moving off, always ensure
doors are locked. The door can only be
that the sliding door is properly
opened from the outside of the vehicle.
closed.
To open the sliding side doors from the
-
Do not use the lower support as a
inside, turn the lock 4 (position A) using
step.
Sliding side door (fuel filler cap
the key.
side)
Depending on the vehicle, opening
the fuel filler flap prevents the slid-
ing side door from opening fully.
➥ 1.147.
1.24
CarManuals2.co
OPENING AND CLOSING THE DOORS (3/6)
5
6
7
7
7
C
D
Opening from the inside
Manual locking
With the door unlocked, pull the
With the 7 button in the unlocked posi-
handle 6 or, depending on the vehi-
tion, turn it towards the front of the vehi-
cle, activate the control 8, then slide
cle (movement C).
the door towards the rear of the vehicle
Manual unlocking
until it locks into the open position.
With the button 7 in the locked position,
Closing from the inside
turn it towards the rear of the vehicle
Push handle 5 towards the front of
(movement D).
the vehicle until the door is completely
closed.
8
1.25
CarManuals2.co
OPENING AND CLOSING THE DOORS (4/6)
9
10
Rear hinged doors
Opening the large door from the
inside
Opening the large door from the
Depending on the vehicle, activate con-
outside
trol 10.
Unlock the door and pull handle 9. To
Do not leave the hinged
unlock the doors ➥ 1.4 ➥ 1.11.
rear doors open in case of
strong winds.
Risk of injury.
For your safety, check that
Before opening the rear hinged
all the vehicle’s doors are
doors, ensure that there is enough
properly closed before
space around to allow the doors to
starting the engine.
be opened.
1.26
CarManuals2.co
OPENING AND CLOSING THE DOORS (5/6)
12
9
11
Opening the small door
Driving with the small door open
Opening the doors to the maximum
position
Move the lever 11 to open the small
While the small door is open, close the
door.
large door.
For each door, press lever 12 to release
the door check strap. Open the door as
After use, open the large door using
far as possible.
If the vehicle is parked on
handle 9 and close the small door
the hard shoulder and a
before closing the large door.
Closing manually from the outside
luggage compartment door
is open, the rear lights may
First close the small door and then
be obscured.
close the large door.
You should make other road-users
Move the doors until the door check
aware of your vehicle by using a
strap is fully engaged on the door
warning triangle or other equipment
striker plate. Make sure that the door
specified by the road traffic regula-
check strap is properly engaged before
tions of the country concerned.
closing the hinged doors.
1.27
CarManuals2.co
OPENING AND CLOSING THE DOORS (6/6)
For your safety, check that
all the vehicle’s doors are
properly closed before
starting the engine.
14
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
13
15
cient alone on your vehicle, even for
a short time.
Tailgate
Opening manually from the inside
They may pose a risk to themselves
or to others by starting the engine,
If it is not possible to unlock the tail-
Opening
activating equipment such as the
gate, it can be unlocked manually from
electric windows or by locking the
Unlock the door, press button 13 and lift
the inside.
doors.
the tailgate. To unlock the doors, ➥ 1.4
Insert a pencil or similar object into
➥ 1.11.
Also, in hot and/or sunny weather,
cavity 15, slide the assembly as shown
please remember that the tempera-
in the diagram and push the tailgate to
Closing
ture inside the passenger compart-
open it.
ment increases very quickly.
Lower the tailgate using the closure
strap 14.
RISK OF DEATH OR SERIOUS
INJURY.
When the tailgate reaches shoulder
height, gently push it shut.
Before opening the tailgate, ensure
that there is sufficient space around
to allow the tailgate to open.
1.28
CarManuals2.co
LOCKING, UNLOCKING THE DOORS (1/3)
If the remote control or,
depending on the vehicle, the
2
card does not work
1
A
In some cases, the radio frequency
remote control or the card may not
work:
- card or radio frequency remote con-
trol battery worn or run flat, vehicle
battery flat etc;
- use of appliances operating on the
same frequency as the card (mobile
phone, etc.);
- vehicle located in a high electromag-
netic radiation zone.
It is then possible:
The card’s built-in key
- to use the radio frequency remote
control or the emergency key inte-
The 2 integrated key can be used to
grated in the card (depending on the
lock or unlock the driver’s door when
vehicle) to unlock the driver’s door;
the card is not working.
- to use the interior door locking/un-
locking control (refer to the following
Access with key 2
pages).
Slide the rear casing
1 downwards
while pressing on zone A.
1.29
CarManuals2.co
LOCKING, UNLOCKING THE DOORS (2/3)
3
B
3
B
6
4
4
2
5
Using the key integrated in
Vehicles with key/remote
Manually locking the front
the card
control
passenger door
- Pull handle 3;
Turn screw 6 with the door open (using
Using the key
the end of the key) and close the door.
- press the cover B on the driver’s
- Pull handle 3;
door down;
This means that the doors are then
- press the cover B on the driver’s
locked from the outside.
- insert the end of the key 2 in the
door down;
notch 4 at the bottom of the cover B;
The doors may then only be opened
- insert the end of the key 5 in the
from the inside or by using the key in
- rotate it upwards to remove the
notch 4 at the bottom of the cover B;
the driver’s door.
cover B;
- rotate it upwards to remove the
- insert the key 2 into the lock of the
cover B;
driver’s door, lock or unlock.
- insert the key 5 into the lock of the
Once you are inside the vehicle, put the
driver’s door, lock or unlock.
key back in its casing in the card.
1.30
CarManuals2.co
LOCKING, UNLOCKING THE DOORS (3/3)
Door and tailgate status
Locking the opening
indicator
elements without the card or
When the ignition is on, the 7 switch
the key
warning light indicates the locking
For example, in the event of a dis-
status of the opening elements:
charged battery or the card or key tem-
porarily not working etc.
7
- indicator light on, the doors and tail-
gate are locked;
With the engine switched off and a
- indicator light off, the doors and tail-
door or tailgate open, press and hold
gate are unlocked.
the 7 switch for more than five seconds.
When you lock the doors, the indicator
When the door is closed, all the doors
light remains lit and then goes out.
and the tailgate will be locked.
Note: unlocking the vehicle from the
outside is only possible with the card in
the vehicle’s access zone or using the
Interior locking/unlocking
key.
door control
Switch 7 controls the doors, the boot
and the fuel filler flap simultaneously.
If a door or the tailgate is open or not
closed properly, the doors and tailgate
lock/unlock quickly.
If transporting an object with the tail-
gate open, you can still lock the doors:
with the engine stopped, press and
Driver’s responsibility
hold switch 7 to lock the other doors.
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those as-
Never leave your vehicle
sisting you to gain access to the
with the key or card inside.
passenger compartment in the
event of an emergency.
1.31
CarManuals2.co
AUTOMATIC LOCKING WHEN DRIVING
NB: if a door is opened or closed, it
Operating faults
will automatically lock again when the
If you experience an operating fault
vehicle reaches a speed of 6 mph (10
(no central locking, the indicator light 1
km/h).
does not light up when trying to lock the
doors and luggage compartment etc.),
1
Activating/deactivating the
make sure that central locking has not
been deactivated by mistake and check
function
that the doors and luggage compart-
To activate: with the vehicle station-
ment are properly closed. If they are
ary and the engine running, press the 1
properly closed, contact an approved
switch until a beep sounds.
dealer.
To deactivate: with the vehicle station-
ary and the engine running, press the
switch 1 until you hear two beeps.
The function can also be activated and
Operating principle
deactivated via the multimedia screen
(depending on the vehicle). ➥ 1.119.
After the vehicle is started, the system
automatically locks the doors when you
are driving at approximately 6 mph (10
km/h) and over.
The door can be unlocked:
- by pressing the central door unlock-
ing switch 1;
- at a standstill, by opening a front
door from inside the vehicle.
Driver’s responsibility
If you decide to keep the
doors locked when you are
driving, remember that it
may be more difficult for those as-
sisting you to gain access to the pas-
senger compartment in the event of
an emergency.
1.32
CarManuals2.co
FRONT HEADRESTS
To raise the headrest
Raise it to its highest position (tilt the
seatback backwards if necessary).
A
Press button 3 and lift the headrest to
2
release it.
1
To refit the headrest
Check that the headrest rods are
clean 2.
Insert the headrest rods into the holes 1
(tilt the seatback backwards if neces-
3
sary). Lower the headrest until it locks
and press button 3 to adjust to the de-
sired height. Check that each rod 2 on
To raise the headrest
the seatback is securely locked.
Pull the headrest upwards to the de-
sired height. Check that it is correctly
locked.
To lower the headrest
Press button 3 and guide the headrest
down to the desired height. Check that
The headrest is important
the bonnet is correctly locked.
for safety. Ensure that it is in
place and in the correct po-
sition: the top of the head-
rest should be as close as possible
to the top of the head and there must
be a minimal distance between the
head and the headrest A.
1.33
CarManuals2.co
FRONT SEATS (1/7)
To avoid all risk of injury,
ensure that nobody is in
2
the proximity of the moving
2
parts. When moving the
seat, make sure that nothing inter-
feres with the moving parts and their
locking.
3
4
1
To move forwards or
To tilt the seatback
For safety reasons, carry
backwards
Depending on the seat, raise the lever 2
out any adjustments
Depending on the seat, lift the bar 1 or
and tilt the seatback until it reaches the
when the vehicle is not
handle 4 to release the seat. Release
position required.
being driven.
the handle at the desired position and
We would advise you not to recline
make sure that it is locked.
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.
Adjusting the height of the
driver’s seat
Nothing should be placed on the
floor (area in front of driver) as such
Move lever 3 as many times as neces-
objects may slide under the pedal
sary:
during braking manoeuvres, thus
- upwards to raise the seat,
obstructing its use.
– downwards to lower the seat.
After making adjustments,
make sure that the seat-
backs are correctly locked
in place.
1.34
CarManuals2.co
FRONT SEATS (2/7)
5
A
7
6
Central armrest 5
To adjust the seat’s lumbar
Version with front bench seat
(depending on the vehicle)
position
for two
Lower handle 6 to increase the support
Depending on the vehicle, the central
and lift it to decrease it.
seatbacks may be folded down.
To fold down the seatback
Pull the 7 tab to unlock the seatback
and lower the seatback A.
When lowering, tilt the headrest so that
it is positioned under the centre con-
sole.
To raise the seatback
Lift the seat back and click it into place.
Check that the bonnet is correctly
locked.
1.35
CarManuals2.co
FRONT SEATS (3/7)
B
8
2
2
4
Estate version flat position
-
pull the lever 2 and pull the seatback
The label B on the seat base reminds
down and forwards. While lowering,
you of these instructions.
Depending on the vehicle, the seatback
tilt the headrest 8 to position it under
on the passenger side may be folded
the dashboard;
down onto the seat base to create a flat
-
press on the seat base to ensure that
position.
it is correctly positioned on the floor;
- Deactivate the front passenger
-
make sure that there is nothing which
airbag ➥ 1.90 ;
will prevent the seat from moving;
- hold handle 4 and move the seat as
-
the seat locks automatically. Check
far back as possible;
that the bonnet is correctly locked.
- hold the top of the seatback to lower
it;
Maximum weight on the seat in the
Be sure to hold the seat-
flat position: 80 kg, with the weight
back when placing it in the
evenly distributed.
flat position.
The label B on the seat base re-
Risk of injury.
minds you of these instructions.
1.36
CarManuals2.co
FRONT SEATS (4/7)
2
Put your hand on the front
Repositioning the seat
of the seat base when repo-
sitioning it.
Make sure that nothing prevents the
seat from moving.
Risk of trapping.
- Pull lever 2 and lift the seatback, en-
suring it is correctly locked;
- reposition the seat base, placing
When the front seatback is
your hand on the front of the seat
in the flat position, you must
base.
deactivate the front passen-
When the rear bench seat is folded
ger airbag.
down, move the front seats carefully.
Risk of serious injury if the airbag is
Remember to reactivate the front pas-
deployed while objects are resting
senger airbag before a passenger oc-
on the seatback in flat position.
cupies the seat ➥ 1.90.
1.37
CarManuals2.co
FRONT SEATS (5/7)
9
F
E
D
10
C
9
Van version flat position
-
press on the seat base to ensure
The label F on the side of the seat base
that it is correctly positioned on the
reminds you of these instructions.
The seatback on the passenger side
floor. There is a risk the seatback
may be folded down onto the seat base
being scratched if it is incorrectly po-
to create a flat position.
sitioned;
- Deactivate the front passenger
-
remove the headrest 9 from the seat;
airbag ➥ 1.90 ;
store the headrest 9 in its housing
- check that the floor is clear of any
under the seat base;
objects;
-
unlock the seatback by lifting
- unlock the seat base by lifting the
handle 10 again and position it hori-
handle 10 and move the seat for-
zontally (movement E).
wards, onto the floor (movement D)
by taking it by the rear section C;
Do not use the headrest
housing 9 to store any other
objects.
Risk of damage to the
seat wiring.
1.38
CarManuals2.co
FRONT SEATS (6/7)
To put the seat back in the comfort po-
sition, proceed in the reverse order.
G
Check that the headrest is positioned
correctly.
Remember to reactivate the front pas-
senger airbag before a passenger oc-
cupies the seat ➥ 1.90.
11
The 11 rings located on each side of
the front passenger seat can be used
to secure the load placed on the seat in
the flat-floor position.
When the front seatback is
in the flat position, you must
deactivate the front passen-
ger airbag.
Maximum weight on the seat in the
flat position: 80 kg, with the weight
Risk of serious injury if the airbag is
evenly distributed.
deployed while objects are resting
on the seatback in flat position.
Maximum height limit for objects on
the seat in flat-floor position: 50 cm.
The label F on the side of the seat
base reminds you of these instruc-
The label G on the side of the seat
For your safety, fasten
tions.
base reminds you of these instruc-
down any objects trans-
tions.
ported with the seat in flat-
floor position.
1.39
CarManuals2.co
FRONT SEATS (7/7)
Operating faults
When an operating fault is detected,
the warning light of the 12 switch for the
seat concerned switches-off after ap-
proximately five seconds.
Consult an approved dealer.
12
Heated seats
With the ignition on:
- pressing the switch 12 on the re-
quired seat for the first time activates
the heating system on high. Both in-
tegrated switch warning lights come
on;
- pressing the switch for the second
time changes the heating to low. One
integrated warning light comes on;
- pressing for the third time turns the
heating off.
1.40
CarManuals2.co
SWIVELLING PARTITION (1/2)
1
2
2
3
To rotate the partition
- pivot the moving section
90 de-
grees, lock it at point 3 and lower
- Deactivate the front passenger
the catch 2. Ensure that the catch is
airbag ➥ 1.90 ;
locked correctly 2.
- place the seat in the flat position
➥ 1.34 ;
The swivelling section must
- unlock the swivelling section of the
always be locked when the
partition by lifting catches 1 and 2;
vehicle is driven.
- before turning the mobile section,
Risk of injury.
ensure that the 1 and 2 catches are
in the unlocked position;
For your safety, fasten
down any objects trans-
When handling, ensure that the seat
ported with the seat in flat-
belt does not become damaged.
floor position.
1.41
CarManuals2.co
SWIVELLING PARTITION (2/2)
Note: before returning the swivelling
1
section to its initial position, check that
the locking points 5 are clean.
5
4
2
Before returning the partition to its initial
position, set catches 1 and 2 to the un-
locked position.
Reset the swivelling section to the ini-
tial position, lock the 2 catch and then,
the 1 catch. Make sure that catches 1
When using the pivoted
and 2 are locked correctly.
partition, the protective
net 4 must not be removed
or disassembled, even par-
tially.
Risk of injury due to the projec-
tion of objects from the rear load
area during braking.
1.42
CarManuals2.co
SEAT BELTS (1/7)
Always wear your seat belt when trav-
Adjusting your driving
elling in your vehicle. You must also
position
comply with the legislation of the par-
- Sit well back in your seat (having
ticular country you are in.
first removed your coat or jacket).
Before starting, first adjust your driv-
This is essential to ensure your back
ing position, then ask all occupants
is positioned correctly;
to adjust their seat belts to ensure
- adjust the distance between the
optimum protection.
seat and the pedals. Your seat
should be as far back as possible
while still allowing you to fully de-
press the pedals. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
Make sure that the rear bench seat
steering wheel;
is locked in position correctly so that
- adjust the position of your head-
the rear seat belts will operate cor-
rest. For maximum safety, your head
rectly. ➥ 3.34.
must be as close as possible to the
headrest;
Incorrectly adjusted or
- adjust the height of the seat. This
twisted seat belts may
adjustment allows you to select the
cause injuries in the event
seat position which offers you the
of an accident.
best possible view;
- adjust the position of the steering
Use one seat belt per person,
wheel.
whether child or adult.
Even pregnant women should wear
a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.
1.43
CarManuals2.co
SEAT BELTS (2/7)
Locking
Unwind the belt slowly and smoothly
and ensure that buckle 3 locks into
catch 5 (check that it is locked by pull-
A
ing on buckle 3).
If the belt jams, allow it to return slightly
before attempting to unwind it again.
If your seat belt is completely jammed,
1
pull slowly, but firmly, so that just over
3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.
3
If there is still a problem, contact an ap-
proved dealer.
4
5
5
Unlocking
2
Press button 4 and the seat belt will be
Adjusting the seat belts
rewound by the inertia reel. Guide the
Depending on the vehicle, if the seat is
belt.
occupied and one of these seat belts is
Sit with your back firmly against the
Driver’s seat belt reminder
not fastened or becomes unfastened
seatback.
ß
while the vehicle is moving at a speed
and, depending on the vehi-
Shoulder strap 1 should be as close as
over approximately 12 mph (20 km/h),
cle, front passengers’ seat belt re-
possible to the base of the neck but not
minder
on it.
the ß
warning light flashes and
This appears on the central display A
a beep sounds for approximately
Lap belt 2 should be worn flat over the
when the ignition is switched on and
120 seconds.
thighs and against the pelvis.
if the driver’s and/or front passenger’s
Note: an object placed on the passen-
The belt should be worn so that it is
seat belt(s) (if the passenger seat is oc-
ger seat may activate the warning light
as close as possible to your body, i.e.:
cupied) is not fastened.
in some cases, depending on the ve-
avoid wearing heavy clothing or keep-
hicle.
ing bulky objects under the belts, etc.
1.44
CarManuals2.co
SEAT BELTS (3/7)
Rear seat belt reminder
When the vehicle speed exceeds
(depending on the vehicle)
12 mph (20 km/h), if one of the rear
seat belts is or becomes unfastened
The 6 graphic is displayed on the in-
during the journey:
strument panel when the ignition is
switched on. This informs the driver of
- the ß
warning light flashes on
the fastening status of each of the rear
the central display;
seat belts every time:
and
- the ignition is switched on;
- a beep sounds for around 120 sec-
- opening a door;
onds;
- fastening or unfastening of a rear
6
and
seat belt.
- the 6 symbol is displayed for approx-
Understanding the graphic 6:
imately 180 seconds and the symbol
- indicator green: seatbelt fastened;
for the seat concerned changes to
red.
When the vehicle speed is less than
- indicator red: seatbelt unfastened;
approximately 12 mph (20 km/h), the
Always make sure that the rear passen-
- indicator grey: seat not occupied.
gers are properly fastened in and that
ß
warning light on the central dis-
the number of seat belts indicated cor-
Depending on the vehicle, the ß
play appears if a rear seat is occupied
responds to the number of rear seats
warning light on the central display also
and the seat belt is not fastened. It is
occupied.
appears when the ignition is switched
accompanied by the 6 symbol which
on, if a rear seat is occupied and the
appears for approximately 60 seconds
Note: in some cases, the warnings may
seat belt is not fastened
each time one of the rear seat belts is
be triggered if an object is placed on
fastened or unfastened.
one of the rear seats.
1.45
CarManuals2.co
SEAT BELTS (4/7)
Rear seat belt reminder
Always make sure that the rear passen-
(continued)
gers are properly fastened in and that
the number of seat belts indicated cor-
The 7 graphic is displayed on the in-
responds to the number of rear seats
strument panel when the ignition is
occupied.
switched on. This informs the driver of
the fastening status of each of the rear
seat belts every time:
- the ignition is switched on;
- opening a door;
7
- fastening or unfastening of a rear
seat belt.
Understanding the graphic 7:
- white symbol: seatbelt fastened;
When the vehicle speed reaches or ex-
- black symbol: seatbelt unfastened;
ceeds 12 mph (20 km/h), if one of the
When the vehicle speed is below ap-
rear seat belts is unfastened during the
proximately
12 mph (20 km/h), the
journey:
graphic 7 appears during approximately
60 seconds every time one of the rear
- the ß
warning light flashes on
seat belts is fastened or unfastened.
the central display;
and
- a beep sounds for around 30 sec-
onds;
and
- the 7 symbol is displayed for at least
60 seconds and the symbol for the
seat concerned changes to black.
1.46
CarManuals2.co
SEAT BELTS (5/7)
8
9
10
11
Adjusting the height of the
“Open Sesame” version front
Version with front bench seat
front seat belts
passenger seat belt
for two
Use button 8 to adjust the seat belt
Slowly unwind belt 9.
In normal use conditions, fasten the
height so that the shoulder strap is worn
centre seat belt when no one is seated
Fasten the sliding buckle 10 into the
as shown previously. Press button 8
there.
catch 11.
and raise or lower the seat belt. Make
sure that the seat belt is locked in posi-
tion correctly after you have adjusted it.
1.47
CarManuals2.co
SEAT BELTS (6/7)
13
13
12
14
15
14
Rear side seat belts 12
Rear centre seat belt
The belts are locked, unlocked and
Slowly unwind belt 13.
adjusted in the same way as the front
Fasten the tongue
14 in the red
belts.
buckle 15.
Check that the rear seat
belts are positioned and
operating correctly each
time the rear bench seat is
moved.
1.48
CarManuals2.co
SEAT BELTS (7/7)
The following information applies to the vehicle’s front and rear seat belts.
- No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and
their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.
- Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too
loosely may cause injury in the event of an accident.
- Never wear the shoulder strap under your arm or behind your back.
- Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around
them.
- The belt should never be twisted.
- Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as
they show any signs of wear.
- When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they
can be used properly.
- Make sure that the buckle is inserted into the appropriate catch.
- Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.
- Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-
jects).
1.49
CarManuals2.co

 

 

 

 

 

 

 

 

Content      ..      1       2         ..

 

//////////////////////////////////////////