Nissan Qashqai (2007-2010). Manual - part 706

BRC-22

< COMPONENT DIAGNOSIS >

[ABS]

C1101, C1102, C1103, C1104 WHEEL SENSOR-1

YES

>> Replace applicable wheel sensor.

NO

>> Replace ABS actuator and electric unit (control unit).

Component Inspection

INFOID:0000000000924971

1.

CHECK DATA MONITOR

On “DATA MONITOR”, select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR”, and “RR RH SEN-
SOR”, and check the vehicle speed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to diagnosis procedure. Refer to 

BRC-20, "Diagnosis Procedure"

.

Wheel sensor

Vehicle speed (DATA MONITOR)

FR LH SENSOR

Nearly matches the speedometer dis-
play (

±

10% or less)

FR RH SENSOR

RR LH SENSOR

RR RH SENSOR

C1105, C1106, C1107, C1108 WHEEL SENSOR-2

BRC-23

< COMPONENT DIAGNOSIS >

[ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

C1105, C1106, C1107, C1108 WHEEL SENSOR-2

Description

INFOID:0000000000977429

ABS unit continually monitors wheel speed sensors to detect abnormal signals.

DTC Logic

INFOID:0000000000924974

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAGNOSIS RESULTS

Check the self-diagnosis results.

Is above displayed on the self-diagnosis display?

YES

>> Proceed to diagnosis procedure. Refer to 

BRC-23, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000001090894

CAUTION:

Do not check between wheel sensor terminals.

INSPECTION PROCEDURE

1.

CHECK SENSOR AND SENSOR ROTOR

• Check sensor rotor for damage. 
• Check wheel sensor for damage, disconnection or looseness.
Are the sensor and sensor rotor normal?

YES

>> GO TO 2.

NO

>> Repair wheel sensor mount or replace sensor rotor. Then perform the self-diagnosis.

2.

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) connector.

3.

Disconnect malfunctioning wheel sensor connector.

4.

Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.

5.

Reconnect connectors and then perform the self-diagnosis. Refer to 

BRC-17, "CONSULT-III Function

(ABS)"

.

Is any item indicated on the self-diagnosis display?

DTC

Display item

Malfunction detected condition

Possible cause

C1105

RR RH SENSOR-2

Signal from rear RH wheel sensor does not match other 
3 wheel speed signals.

• Sensor not installed correctly
• Sensor rotor or encoder dam-

aged

• Sensor rotor loose on axle
• Electrical interference
• Wheel not turning - e.g. vehi-

cle driven on 2WD dyno

• Sensor damaged
• ABS unit damaged

C1106

RR LH SENSOR-2

Signal from rear LH wheel sensor does not match other 
3 wheel speed signals.

C1107

FR RH SENSOR-2

Signal from front RH wheel sensor does not match other 
3 wheel speed signals.

C1108

FR LH SENSOR-2

Signal from front LH wheel sensor does not match other 
3 wheel speed signals.

Self-diagnosis results

RR RH SENSOR-2

RR LH SENSOR-2

FR RH SENSOR-2

FR LH SENSOR-2

BRC-24

< COMPONENT DIAGNOSIS >

[ABS]

C1105, C1106, C1107, C1108 WHEEL SENSOR-2

YES

>> GO TO 3.

NO

>> Poor connection of connector terminal. Repair or replace connector.

3.

CHECK WHEEL SENSOR HARNESS

1.

Turn ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) connector.

3.

Disconnect malfunctioning wheel sensor connector.

4.

Check continuity between terminals. (Also check continuity when steering wheel is turned right and left
and when sensor harness inside the wheel house is moved.)

Measurement terminal for power supply circuit

Measurement terminal for signal circuit

Measurement terminal for ground circuit

5.

Reconnect ABS actuator and electric unit (control unit) connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace malfunctioning components.

4.

CHECK WHEEL SENSOR POWER SUPPLY CIRCUIT

1.

Turn ignition switch ON.

2.

Check voltage between wheel sensor harness connector power supply terminal and ground.

Is the inspection result normal?

YES

>> Replace applicable wheel sensor.

NO

>> Replace ABS actuator and electric unit (control unit).

Component Inspection

INFOID:0000000001090895

ABS actuator and electric unit (control unit)

Wheel sensor

Continuity

Connector

Terminal

Connector

Terminal

E34

9

E39 (Front RH)

2

Existed

16

E22 (Front LH)

8

B41 (Rear RH)

6

B44 (Rear LH)

ABS actuator and electric unit (control unit)

Wheel sensor

Continuity

Connector

Terminal

Connector

Terminal

E34

10

E39 (Front RH)

1

Existed

5

E22 (Front LH)

19

B41 (Rear RH)

17

B44 (Rear LH)

ABS actuator and electric unit (control unit)

Continuity

Connector

Terminal

Connector

Terminal

E34

9, 10

E34

1, 4

Not existed

16, 5

8, 19

6, 17

Wheel sensor

—

Voltage

Connector

Terminal

E39 (Front RH)

2

Ground

8 V or more

E22 (Front LH)

B41 (Rear RH)

B44 (Rear LH)

C1105, C1106, C1107, C1108 WHEEL SENSOR-2

BRC-25

< COMPONENT DIAGNOSIS >

[ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

1.

CHECK DATA MONITOR

On “DATA MONITOR”, select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR”, and “RR RH SEN-
SOR”, and check the vehicle speed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to diagnosis procedure. Refer to 

BRC-35, "Diagnosis Procedure"

.

Wheel sensor

Vehicle speed (DATA MONITOR)

FR LH SENSOR

Nearly matches the speedometer dis-
play (

±

10% or less)

FR RH SENSOR

RR LH SENSOR

RR RH SENSOR