Nissan Qashqai (2007-2010). Manual - part 400

 

  Index      Nissan     Nissan Qashqai - service and repair manual 2007 - 2010 year

 

Search            copyright infringement  

 

 

 

 

 

 

 

  

 

Content   ..  398  399  400  401   ..

 

 

Nissan Qashqai (2007-2010). Manual - part 400

 

 

P1124, P1126 THROTTLE CONTROL MOTOR RELAY

EC-1119

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P1124, P1126 THROTTLE CONTROL MOTOR RELAY

Description

INFOID:0000000001094195

Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle
control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends
an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition
switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not
provided to the ECM.

DTC Logic

INFOID:0000000001094196

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8V.

Witch DTC is detected?

P1126 >> GO TO 2.
P1124 >> GO TO 3.

2.

PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P1126

1.

Turn ignition switch ON and wait at least 2 seconds.

2.

Start engine and let it idle for 5 seconds.

3.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-1122, "Diagnosis Procedure"

.

NO

>> INSPECTION END

3.

PERFORM DTC CONFIRMATION PROCEDURE FOR DTC P1124

1.

Turn ignition switch ON and wait at least 1 second.

2.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-1122, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000001094197

1.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I

1.

Check the voltage between ECM harness connector and ground.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1124

Throttle control motor 
relay circuit open

ECM detects a voltage of power source for 
throttle control motor is excessively low.

• Harness or connectors

(Throttle control motor relay circuit is 
open)

• Throttle control motor relay

P1126

Throttle control motor 
relay circuit short

ECM detect the throttle control motor relay is 
stuck ON.

• Harness or connectors

(Throttle control motor relay circuit is 
shorted)

• Throttle control motor relay

EC-1120

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

P1124, P1126 THROTTLE CONTROL MOTOR RELAY

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

1.

Disconnect ECM harness connector.

2.

Disconnect IPDM E/R harness connector E12.

3.

Check the continuity between ECM harness connector and IPDM E/R harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E7, F121
• Harness for open or short between ECM and IPDM E/R

>> Repair open circuit or short to ground or short to power in harness connectors.

4.

CHECK FUSE

1.

Disconnect 15A fuse (No. 51) from IPDM E/R.

2.

Check 15A fuse for blown.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Replace 15A fuse.

5.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I

1.

Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> GO TO 6.

6.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II

1.

Check the continuity between ECM harness connector and IPDM E/R harness connector.

2.

Also check harness for short to ground and short to power.

ECM

Ground

Voltage

Connector

Terminal

F7

15

Ground

Battery voltage

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E12

25

F7

15

Existed

ECM

Ground

Condition

Voltage

Connector

Terminal

F7

2

Ground

Ignition switch OFF

Approx. 0V

Ignition switch ON

Battery voltage

IPDM E/R

ECM

Continuity

Connector

Terminal

Connector

Terminal

E12

32

F7

2

Existed

P1124, P1126 THROTTLE CONTROL MOTOR RELAY

EC-1121

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> GO TO 7.

7.

DETECT MALFUNCTIONING PART

Check the following.
• Harness connectors E7, F121
• Harness for open or short between ECM and IPDM E/R

>> Repair open circuit or short to ground or short to power in harness connectors.

8.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace harness or connectors.

EC-1122

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

P1128 THROTTLE CONTROL MOTOR

P1128 THROTTLE CONTROL MOTOR

Description

INFOID:0000000001094198

The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle control motor to make the throttle valve opening angle properly in
response to driving condition.

DTC Logic

INFOID:0000000001094199

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON and wait at least 2 seconds.

2.

Start engine and let it idle for 5 seconds.

3.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-1125, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000001094200

1.

CHECK GROUND CONNECTION

1.

Turn ignition switch OFF.

2.

Check ground connection E9. Refer to Ground Inspection in 

GI-41, "Circuit Inspection"

. 

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace ground connection.

2.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Disconnect electric throttle control actuator harness connector.

2.

Disconnect ECM harness connector.

3.

Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1128

Throttle control motor 
circuit short

ECM detects short in both circuits between 
ECM and throttle control motor.

• Harness or connectors

(Throttle control motor circuit is shorted.)

• Electric throttle control actuator

(Throttle control motor)

Electric throttle control actuator

ECM

Continuity

Connector

Terminal

Connector

Terminal

F29

5

F7

1

Not existed

4

Existed

6

1

Existed

4

Not existed

 

 

 

 

 

 

 

Content   ..  398  399  400  401   ..