Can-Am MAVERICK R — X AND X RS SERIES. OPERATOR’S GUIDE (2024)

TRANSPORTING THE VEHICLE

Using a Winch to Pull Vehicle

4. When loaded, engage the PARK

and attach the vehicle securely.

Onto Trailering Equipment

When vehiclle cannot cllimb on iits

Securing Vehicle for

own power, proceed as folllows;

Transport

WARNING

Have the help of an assistant.

To avoid severe injjury or death or

One person should be in vehiiclle

damage to iimportant components.

to have access to vehiclle steer-

–

Never use the wiinch cablle/

ing, brakes and winch switch,

rope to retaiin a vehicle during

whiile the other person controls

traiileriing.

the environment and safety of the

–

Never ride with the winch ca-

maneuver.

ble/rope attached to a load or

another vehiclle.

WARNING

–

Onlly use the wiinch to hellp a

stuck vehicle (snow, mud,

Ensure the winch hook can be

etc.).

safelly attached to a proper an-

–

Allways refer to the winch man-

choriing poiint. Use proper riiggiing.

ufacturer''s instructions before

pullliing loads.

NOTE:

If vehicle can be started safely, let en-

Ensure the PARK is selected (if

gine idle during winching to avoid

possible).

draining the battery.

Remove the key from the D.E.S.S.

post.

Choice one of the following

Secure the vehicle by using UTV

options:

tire-bonnets so that the vehicle

1. Start the engine and select the

suspension is free to move during

NEUTRAL (N).

transportation.

2. If the engine cannot be started,

use the PERMANENT neutral.

If not possible, secure the rear of

3. If the electrical system cannot

the vehicle on both sides using a

be powered (or boosted) or if

strap around the trailing arm as

the shifting actuator is defec-

close to the wheel as possible.

tive, use the MECHANICAL

neutral.

If the vehicle is equipped with a

winch, use the winch to roll the ve-

hicle on the platform.

If the vehicle is not equipped with a

winch:

1. Attach a strap to the front re-

covery hook.

2. Attach the strap to the winch

cable

the

trailering

equipment.

3. Load the vehicle onto or into

the trailering equipment.

Trailing arm

131

LIFTING AND SUPPORTING THE VEHICLE

Front of Vehicle

1. Place vehicle on a flat non slippery

ground.

2. Block the rear wheels properly to

avoid any unexpected vehicle

movements

3. Install an hydraulic jack under the

rear of the front lower plate.

REAR OF VEHICLE

1. Hydraulic jack position

4. Lift rear of vehicle and install a jack

stand on each side under frame as

shown below.

NOTICE

Make sure to aliign the jack stands

4. Lift front of vehicle and install a

wiith the tubular frame under the

jack stand on each side under

skid plate.

frame as shown below.

NOTICE

Make sure to allign the jjack stands

with the tubullar frame under the

skiid plate.

JACK STAND POSITIONS

- REAR OF

VEHICLE

5. Lower hydraulic lift and ensure ve-

hicle is supported safely onto both

jack stands.

JACK STAND POSITIONS - FRONT OF

VEHICLE

5. Lower hydraulic lift and ensure ve-

hicle is supported safely onto both

jack stands.

Rear of Vehicle

1. Place vehicle on a flat non slippery

ground.

2. Block the front wheels properly to

avoid any unexpected vehicle

movements

3. Install an hydraulic jack under the

vehicle.

133

MAINTENANCE SCHEDULE

Maintenance is very important to keep your vehicle in safe operating condition.

The vehicle should be serviced as per the maintenance schedule.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

Perform periodic checks and follow the maintenance schedule. The maiinte-

nance schedule does not exempt the pre-ride inspection.

WARNING

Faiilure to properly maiintain the vehiclle accordiing to the maiintenance

schedulle and procedures can make it unsafe to operate.

EPA Regulation - Canadian and USA Vehicles

A repair shop or person of the owner''s choosing may maiintaiin, replace, or

repair emission control devices and systems. These instructions do not require

components or service by BRP or authorized Can-Am Off-road dealers.

Although an authorized Can-Am Off-road dealer has an in-depth technical knowl-

edge and tools to service your vehicle, the emission-related warranty is not con-

ditioned on the use of an authorized Can-Am Offroad dealer or any other

establishment with which BRP has a commercial relationship.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

For emission-related warranty claims, BRP is limiting the diagnosis and repair of

emission-related parts to the authorized Can-Am Offroad dealers. For more infor-

mation, please refer to the US EPA Emission-Related Warranty contained in the

Warranty section.

You must follow the instructions for fuel requirements in the fueling section of this

manual. Even if gasoline containing greater than ten volume percent ethanol is

readily available, the US EPA issued a prohibition against the use of gasoline

containing greater than 10 vol% ethanol that applies to this vehicle. The use of

gasoline containing greater than 10 vol% ethanol with this engine may harm the

emission control system.

Air Filter Maintenance Guideline

Air filter maintenance should be adjusted according to riding conditions.

Air filter maintenance must be increased in frequency when riding on snow, dry

sand, dirt, gravel or similar conditions which have a high dust or particle

dispersion.

Riding in a group in these conditions will require increasing the air filter mainte-

nance frequency further.

NOTE:

Accessory filters and pre-filter are available for such conditions. Contact an au-

thorized Can-Am off-road dealer for details.

136

MAINTENANCE SCHEDULE

Severe Duty Use

If your vehicle is used in the following conditions, refer to the Severe Duty section

of the maintenance schedule.

- Sand dunes riding.

- Driving at excessive speeds for prolonged amount of time.

- Repeated carrying of loads at more than 75% the maximum capacity.

- The increase workload applied to the drive system accelerates the differ-

entials, gearbox/transmission, and engine oil life. This reduces internal

component longevity if not replaced more frequently.

Extreme Cold Condiitiion

An engine that is frequently operated at or below an ambient temperature of -25 °

C (-13 °F) will require an increase in service and maintenance schedule.

Any combustion engine operated at these low ambient temperature will collect

an increased amount of condensation at every startup/warm-up.

Since the engine is not reaching operating temperatures for extended periods of

time, the oil is starting to be strongly diluted with water and gas residue (more

water content).

An engine needs to reach operating temperature, in order to be able to evaporate

condensate out of the oil.

If daily usage (work or leisure driving cycle) is similar to those mentioned below,

BRP strongly recommends changing the oil at least once a month.

Parameters of an increase in service and maintenance schedule:

- Engine not reaching the proper operating temperature during normal daily

usage

- Multiple starts and stops without reaching operating temperature

- Short idle periods

- Low RPM driving cycle in short distances without reaching operating

temperature.

NOTE:

BRP strongly recommends the installation of a block heater to help warm up the

liquids, this will also help to extend the oil lifetime.

Deep Mud / Water Use

This type of usage requires more frequent maintenance and inspections to en-

sure debris has not infiltrated mechanical components.

If you ride in deep mud or water, be sure to perform the following Post Operation

Care for Deep Mud / Water Environment list.

Post Operatiion Care for Deep Mud / Water Environment

- Rinse the vehicle and its components with fresh water.

- Inspect and clean engine air filter and engine air filter housing.

137

MAINTENANCE SCHEDULE

- Clean radiators and intercooler.

- Visually inspect for any water accumulation in the vent hoses (fuel tank, gear-

box, front differential and rear final drive). If there is water, bring the vehicle to

your nearest authorized Can-Am Off-road dealer for inspection and servicing

of main components related to the vents.

- Clean front and rear shock absorbers to prevent seal from damage by dust or

dirt.

- Clean drive shaft bellows and the propeller shaft yokes or bellows.

Maintenance Schedule

Make sure to perform proper maintenance at recommended intervals as indi-

cated in the tables.

The maintenance chart intervals are based on 3 factors:

- Calendar time

- Vehicle hours

- Odometer reading.

Take in account whichever comes first to determine the maintenance threshold.

Your driving habits determines the factors you shall adhere too. For example:

- Someone who uses their vehicle every other weekend trail riding with friends

would most likely follow the odometer readiing to determine the maintenance

interval.

- Someone who uses their vehicle seldomly over the year or only on a few oc-

casions (hunting, camping) would most likely follow the callendar time to de-

termine the maintenance interval.

- Someone who uses their vehicle daily / weekly for long periods of time such

as agricultural / work would most likely follow the vehiicle hours to determine

the maintenance interval.

IMPORTANT: The following tables show the appropriate maintenance appli-

cation for the first

3 years. For subsequent years, repeat the same pattern

alternatively.

Regular Maintenance Overview

Calendar

Vehicle Hours

Odometer

Regular Duty

Years

3000 km

100

(1900 mi)

6000 km

200

A+B

(3700 mi)

9000 km

300

(5600 mi)

138

MAINTENANCE SCHEDULE

REGULAR DUTY

A=Adjust

Every year

Every 2 years

C=Clean

I=Inspect

100 hours

200 hours

L=Lubricate

R=Replace

3000 km

6000 km

T=Torque

(1900 mi)

(3700 mi)

Air and Fuel Delivery

Engine air filter

I, C, R

Air delivery components and function (airbox,

I, C

throttle body, ducts, clamps)*

Fuel components and function (Fuel tank cap,

fuel tank, hoses, clamps, leaks)*

Fuel pump pressure

Body and Chassis

Cage fasteners

Seat belts retractors, buckles and

I, C

semi-cinching

Engine and Cooling

Engine oil and filter

Engine cooling components (coolant specific

gravity, coolant level, hoses condition,

I, C, A

clamps, leaks)*

Coolant

Every 5 years or 12 000 km (7500 mi)

As per vehicle

Spark plugs

hours and

odometer only,

Not calendar time

Radiators

Engine seals and gaskets

Exhaust and Emissions

Fuel tank vent breather filter (except EVAP

models)

Canister vent pre-filter (EVAP models)

Exhaust components (gaskets, pipes, muffler

condition, leaks)*

Exhaust clamping rings

Muffler spark arrester

Debris around exhaust pipe and muffler area

140

MAINTENANCE SCHEDULE

REGULAR DUTY

A=Adjust

Every year

Every 2 years

C=Clean

I=Inspect

100 hours

200 hours

L=Lubricate

R=Replace

3000 km

6000 km

T=Torque

(1900 mi)

(3700 mi)

Brake

Brake components and function (brake pads,

brake discs, calipers, brake lines, master

I, C, L

cylinder)*

Brake fluid

Every 2 years

Drive

Replace at first 3000 km (1900 mi) and

Gearbox oil and filter

at 6000 km (3700 mi), then follow the

regular schedule

Gearbox oil and filter

I, A

Drive components (drive shaft (bellows,

joints, seals), propeller shaft U-joint, wheel

bearing)*

Front differential oil

Replace at first 3000 km (1900 mi) and

Final drive oil

6000 km (3700 mi), then follow the

regular schedule

Final drive oil

Disconnect unit oil

Tires (wear and pressure)

I, A

Wheel beadlock screws (if equipped)

Wheel lug nuts

Rear wheel scrappers and rock deflectors

I, C

Electrical

Battery connections and condition

I, C

Operation of control switches and lighting

Electronic modules (Fault codes and

applicable software updates)

Steering

Steering components and function (rack and

pinion, steering column, tie-rod)*

Suspension

Suspension components and function (shock

C, L, T

absorber, spherical bearings, ball joints,

141

MAINTENANCE SCHEDULE

SEVERE DUTY

A+

Every 6

A=Adjust

Every year

Every 2 years

months

C=Clean

I=Inspect

100 hours

200 hours

50 hours

L=Lubricate

R=Replace

3000 km

6000 km

1500 km

T=Torque

(1900 mi)

(3700

mi)

(900 mi)

Air and Fuel Delivery

Engine air filter

I, C

Air delivery components and

function (airbox, throttle body,

I, C

ducts, clamps)*

Fuel components and function

(Fuel tank cap, fuel tank, hoses,

clamps, leaks)*

Fuel pump pressure

Body and Chassis

Cage fasteners

Seat belts retractors, buckles

I, C

and semi-cinching

Engine and Cooling

Engine oil and filter

Engine cooling components

(coolant specific gravity, coolant

I, C, A

level, hoses condition, clamps,

leaks)*

Coolant

Every 5

years or 12 000 km (7500 mi)

As per vehicle

hours and

Spark plugs

odometer only,

Not calendar

time

Radiators

Engine seals and gaskets

Exhaust and Emissions

Fuel tank vent breather filter

(except EVAP models)

Canister vent pre-filter (EVAP

models)

143

MAINTENANCE SCHEDULE

SEVERE DUTY

A+

Every 6

A=Adjust

Every year

Every 2 years

months

C=Clean

I=Inspect

100 hours

200 hours

50 hours

L=Lubricate

R=Replace

3000 km

6000 km

1500 km

T=Torque

(1900 mi)

(3700 mi)

(900 mi)

Exhaust components (gaskets,

pipes, muffler condition, leaks)*

Exhaust clamping rings

Muffler spark arrester

Debris around exhaust pipe and

muffler area

Brake

Brake components and function

(brake pads, brake discs,

I, C, L

calipers, brake lines, master

cylinder)*

Brake fluid

Every 2 years

Drive

Replace at first

1500 km (900 mi) and at 3000 km

Gearbox oil and filter

1900 mi), then follow the regular schedule

Gearbox oil and filter

I, A

Drive components (drive shaft

(bellows, joints, seals), propeller

shaft U-joint, wheel bearing)*

Front differential oil

Replace at first 1500 km (900 mi) and at 3000 km

Final drive oil

1900 mi), then follow the regular schedule

Final drive oil

Disconnect unit oil

Tires (wear and pressure)

I, A

Wheel beadlock screws (if

equipped)

Wheel lug nuts

Rear wheel scrappers and rock

I, C

deflectors

Electrical

Battery connections and

I, C

condition

144

MAINTENANCE SCHEDULE

SEVERE DUTY

A+

Every 6

A=Adjust

Every year

Every 2 years

months

C=Clean

I=Inspect

100 hours

200 hours

50 hours

L=Lubricate

R=Replace

3000 km

6000 km

1500 km

T=Torque

(1900 mi)

(3700

mi)

(900 mi)

Operation of control switches

and lighting

Electronic modules (Fault codes

and applicable software

updates)

Steering

Steering components and

function (rack and pinion,

steering column, tie-rod)*

Suspension

Suspension components and

function (shock absorber,

spherical bearings, ball joints,

I, C, L, T

suspension arms, stabilizer bar

links and clamps)*

Stabilizer bar bushings

Recommended

lubrication

every 1000 km

(620 mi)

*For an extensive list of maintenance actions to be performed, refer to your local

Can-Am Off-road dealer.

145

MAINTENANCE PROCEDURES

This section includes instructions for

- Riding on dry gravel trails or simi-

basic maintenance procedures.

lar conditions.

- Riding in areas with high concen-

Due to the complexity of some of the

tration of seeds or crop husks.

maintenance procedures, good me-

- Riding in severe snow conditions.

chanical skills are required. If you are

not comfortable with these proce-

NOTICE

dures, do not hesitate to contact an

authorized Can-Am off-road dealer,

When riding iin dusty condiitiions or

repair shop or person of your own

sand, the aiir box needs to be

choosing.

clleaned before every ride.

WARNING

NOTE:

Riding in a group, under these condi-

Unlless otherwise indiicated, al-

tions, increases the frequency of the

ways remove D.E.S.S. key from

air filter maintenance.

the D.E.S.S. post before perform-

ing any maintenance and remove

Removiing the Engine Aiir Fillter

key.

1. From the left-rear wheel well, open

the four retaining clips on the air fil-

WARNING

ter cover.

Should removall of a llockiing de-

vice be required (e.g. llock tab,

self-lockiing fastener, etc.) , all-

ways replace iit wiith a new one.

ENGINE AIR FILTER

NOTICE

Never modify the air intake sys-

tem. Otherwiise, engiine perform-

ance degradation or damage can

occur. The engiine iis caliibrated to

RETAINING CLIP - TYPICAL

operate specificallly wiith these

2. Remove the air filter element from

components.

its housing.

Engine Aiir Fillter Replacement

Guiideline

Engine air filter inspection and re-

placement frequency should be ad-

justed according to riding conditions

as it is critical to ensure proper engine

performance and life span.

Engine air filter inspection and re-

placement frequency must be in-

creased for the following severe riding

conditions:

Cleaning the Engiine Air Fiilter

- Riding on dry sand.

1. Inspect the filter for any signs of

- Riding on dry dirt covered

leaks. A streak of dust on the clean

surfaces.

151

MAINTENANCE PROCEDURES

side of the filter is a telltale sign.

Replace filter if there is any dam-

ages. Eliminate any source of air

leaks before installing a new filter.

2. Clean engine air filter by tapping

out heavy dust from paper ele-

ment, this will allow dirt and dust to

get out of the paper filter.

NOTICE

It is not recommended to blow

Ensure that the element is properly

compressed air on the paper elle-

seated.

ment; thiis could damage the pa-

Position the air filter cover on the

per fibers and reduce iits filltratiion

housing and secure it using

the

abiiliity when used iin dusty envi-

four retaining clips.

ronments. If engine air fiilter is too

diirty and cannot be cleaned fol-

lowiing the recommended proce-

dure, it shoulld be replaced.

3. Use a clean damp cloth to wipe

both the filter sealing surface and

the inside of the outlet tube. En-

sure that the outlet tube sealing

area is undamaged.

4. Inspect air filter housing for

cleanliness.

RETAINING CLIP - TYPICAL

Cleaning the Engiine Air Fiilter

Housiing

FRONT GRILLE

1. Inspect air filter housing for

cleanliness.

Removing the Front Grillle

The front grille is located in fascia.

NOTICE

If sand or other particles are

found iin air fillter housing, cllean iit

using a vacuum cleaner.

Installling the Engiine Air Fillter

1. Insert the new engine air filter ele-

ment into its housing.

1. Press down the upper section of

the grille.

2. Carefully pull the grille forward to

release its four tabs from the

spring clips in the fascia.

152

MAINTENANCE PROCEDURES

Installliing the Front Griillle

1. Carefully press the grille into the

fascia so that its four tabs engage

the spring clips.

2. Verify that the grille is properly

clipped.

EVAPORATIVE EMISSION

SYSTEM PRE-FILTER (If

Equipped)

Remove the pre-filter assembly.

Replacing the Evaporatiive

Secure the new pre-filter on frame.

Emiissiion System Pre-Fillter

Tightening Torque

The pre-filter is located under the

right-rear fender.

Pre-filter

2.5 ± 0.5 Nm

screws

(22 ± 4 lbf-in)

Connect the inlet and outlet hoses

to the pre-filter.

Secure the hoses using new Oe-

tiker clamps.

ENGINE OIL

Recommended Engiine Oiil

NOTICE

Remove the Oetiker clamps that

Do not fill the engiine oiil iinto the

secure the inlet and outlet hoses to

gearbox. The gearbox requires

the pre-filter.

DCT oill and gear oill.

Rotax^® engines were developed and

validated using the XPS^® oil. BRP rec-

ommends the use of its XPS engine

oil or an equivalent at all time. Dam-

ages caused by the use of an oil not

suitable for the engine may not be

covered by the BRP Limited Warranty.

2. Disconnect the hoses from the

pre-filter

3. Remove both retaining screws.

153

MAINTENANCE PROCEDURES

XPS Recommended Engiine Oiil

NOTICE

The engiine oiil llevel verifiication

General

5W40 Synthetic oil

must be performed within 1 mi-

purpose

nute after engine shutdown.

Cold

tempera

0W40 Synthetic oil

Through the right-rear wheel well,

ture

unscrew the dipstick. Then remove

it and wipe it clean.

Warm

tempera

10W50 Synthetic oil

ture

If the recommended XPS engine oil is

not available:

- Use a 4-stroke SAE engine syn-

thetic oil meeting or exceeding the

following lubricant industry

specifications

- Always check the API service label

certification on the oil container, it

must contain the indicated

Reinsert the dipstick and screw it

in completely.

standards.

Remove the dipstick and check the

- API service cllassifiication SN

oil level. It should be at or near the

and JASO MA2

upper (MAX) mark.

Veriifyiing the Engine Oill Level

NOTICE

Operatiing the engiine wiith an im-

proper oill level may severely dam-

age the engine.

The engine oil level must be checked

at normal operating temperature, ei-

ther after riding or after letting the en-

gine idle for at least 10 min.

MAX

NOTE:

MIN

The engine is at normal operating

Operating range

temperature when the temperature in-

dicator on the right lateral display

If oil needs to be added, insert a

shows 5 bars.

funnel into the dipstick tube.

To avoid overfilling, add a small

1. Place the vehicle on a level

amount of recommended engine

surface.

oil then recheck the oil level. Refer

2. Engage the PARK.

to Recommended Engine Oil.

3. Start the engine and let it idle for at

least 20 seconds.

4. Stop the engine.

154

MAINTENANCE PROCEDURES

7. To avoid spillage, install a funnel

Oil Quantity Between MIN and

between the drain holes and the

MAX Marks

skid plate.

600 ml

(20.3 fl oz (US))

Funnel

10. Repeat the previous step until the

oil level reaches the upper (MAX)

(P/N 529000155)

mark on the dipstick.

8. Place a drain pan under both en-

NOTICE

gine drain plugs.

Do not overfilll.

9. Unscrew both magnetic drain

plugs. Discard the gasket rings

and O-ring.

11. Install the dipstick and tighten it

properly.

12. Wipe off any spillage.

Changing the Engiine Oiil

The engine oil and filter must be

changed at the same time, with a

warm engine.

CAUTION

The engiine oiil can be very hot. Al-

1. Magnetic drain plug (magneto cover)

low iit to cooll sufficiently before

2. O-ring

you begin.

3. Magnetic drain plug (oil tank cover)

4. Gasket ring

5. O-ring

Place the vehicle on a level

surface.

10. Allow the oil to drain completely

Put the vehicle on PARK.

from the crankcase.

Start the engine and let it run at

11. Clean the magnetic drain plugs of

idle for at least 2 minutes.

metal shavings and residue. The

Stop the engine.

presence of debris gives an indica-

Remove the dipstick.

tion of internal engine damage.

Clean the area around the drain

12. Install new gasket rings and

plugs.

O-rings on the magnetic drain

plugs.

NOTICE

Never re-use gasket riings or

O-riings.

Always replace them with NEW

ones.

A missing or damaged O-ring willl

cause a lloss of oiil pressure and

possiible engiine damage.

Magnetic drain plug (magneto cover)

Magnetic drain plug (oil tank cover)

155

MAINTENANCE PROCEDURES

13. Tighten the magnetic drain plugs

to specification.

Tighteniing Torque

Magnetic drain

30 ± 3 Nm

plugs

(22 ± 2 lbf-ft)

14. Replace the oil filter. Refer to Re-

placing the Engine Oil Filter.

15. Refill the engine with the recom-

Remove the oil filter cover. Discard

mended engine oil. Refer to Rec-

the O-ring.

ommended Engine Oil

Remove and discard the oil filter.

Check and clean the oil filter inlet/

Engiine Oiil Capacity

outlet area for dirt and other

contaminations.

Engine oil and

2.8 l

engine oil filter

(2.96 qt

replacement

(liq.,US))

16. After filling, start the engine and

check the oil level, refer to Verify-

ing the Oil Level.

17. Wipe off any spillage.

18. Dispose of the used oil and filter

per

local

environmental

regulations.

Oil inlet orifice from the oil pressure pump

Oil outlet orifice to the engine lubrication

ENGINE OIL FILTER

system

Oil filter housing

Engiine Oiil Fiilter Location

The oil filter is located on the right side

Wet a NEW O-ring with engine oil

of the engine.

and slip it onto the oil filter cover.

Install a NEW engine oil filter into

the oil filter cover.

Apply engine oil to the seal on the

open end of the oil filter.

Repllaciing The Engiine Oiil Fillter

1. Clean the oil filter area.

APPLY ENGINE OIL HERE

8. Install the new filter into its

housing.

156

MAINTENANCE PROCEDURES

NOTICE

CAUTION

Engine oill fillter and gearbox oiil fiil-

Before proceeding, wait for the ra-

ter are simillar, do not miix them.

diiator to cool.

The engiine oiil fiilter has a closed

end whille the gearbox oill filter iis

2. Inspect the radiator hoses for

opened on both ends and the

leaks or damage. Replace if

word gearbox iis allso marked on iit.

necessary.

Engine Oil

Gearbox Oil

Filter

1. Opened

end (relief

1. Closed

valve)

end

LOWER RADIATOR HOSE

2. Gearbox

1. Radiator

indication

2. Hose clamp

9. Tighten oil filter cover screws to

3. Lower radiator hose

specification.

NOTICE

Pay attentiion to avoiid pinchiing

the O-riing duriing fillter and cover

installatiion.

Tiightening Torque

Oil filter cover

9 ± 1 Nm

screws

(80 ± 9 lbf-in)

UPPER RADIATOR HOSE

10. Wipe off any oil spillage on the

1. Hose clamp

engine.

2. Upper radiator hose

11. Dispose of the used oil filter as per

your

local

environmental

3. Inspect the radiator fins. They

regulations.

must be free of any foreign materi-

al that would impair cooling.

FRONT RADIATOR

4. Use a garden hose to rinse the

fins.

Inspecting and Clleaniing the Front

Radiator

1. Remove the front grille, refer to

Removing the Front Grille.

157

MAINTENANCE PROCEDURES

NOTICE

Be carefull not to damage the radii-

ator fins when clleaniing. Use a

low-pressure stream of water.

Never use a HIGH-PRESSURE

washer. Do not use any tool that

could damage the fiins.

5. Re-install the front grille. Refer to

Installing the Front Grille.

UPPER RADIATOR HOSE — RIGHT-REAR

WHEEL WELL

INTERCOOLER AND REAR

Remove the plastic rivet on the top

RADIATOR

of the air intake grille located be-

hind seats.

Inspectiing and Cleaning the

Intercooler / Rear Radiiator

1. Inspect the radiator hoses for

leaks or damage. Replace if

necessary.

CAUTION

Before proceeding, wait for the ra-

diiator to cooll.

Unclip and remove the air intake

grille.

Inspect the intercooler fins and the

radiator fins. They must be free of

any foreign material that would im-

pair cooling.

Use a garden hose to clean the in-

tercooler and the rear radiator fins.

NOTICE

Be careful not to damage the in-

LOWER RADIATOR HOSE — LEFT-REAR

tercooler fins or radiiator fins when

WHEEL WELL

cleaniing. Use a llow-pressure

stream of water. Never use a

HIGH-PRESSURE washer. Do not

use any tool that could damage

the fins.

158

MAINTENANCE PROCEDURES

1. Intercooler

REMOVING THE SERVICE COVER

2. Rear radiator

1. Depress latch

2. Tilt rearward

ENGINE COOLANT

3. Check that the coolant level is at

Recommended Engine Coollant

the MAX line on the side of the

reservoir.

XPS Recommended Coolant

Extended life pre-mixed coolant

If XPS is not availlablle

Distilled water and antifreeze

solution (50% distilled water, 50%

antifreeze)

NOTICE

Allways use ethyllene-glycoll antii-

4. Add coolant to the reservoir as

freeze containing corrosiion iinhiibi-

necessary. Refer to Cooling Sys-

tors speciifiicallly for internall

tem Refilling and Bleeding

combustion alumiinum engines.

Engiine Coollant Replacement

Verifying the Engiine Coolant Level

Draining the Cooliing System

WARNING

Check coolant level with engiine

cold.

In order to avoiid potentiial burns,

do not remove the pressure cap or

loosen the coolant drain pllug iif

1. Place the vehicle on a level

the engiine iis hot.

surface.

2. To remove the service cover, de-

press the latch and tilt the cover

1. Lift the rear of the vehicle approxi-

rearward.

mately 30 cm (12 in).

159

MAINTENANCE PROCEDURES

7. Remove the hose pincher to drain

the remaining coolant from the

system.

8. Install the radiator hose using a

new Oetiker clamp.

9. Fill the cooling system with cool-

ant. Refer to Refilling and Bleeding

the Cooling System.

Refillliing and Blleediing the Cooliing

System

A. A = 30 cm (12 in)

1. Remove the pressure cap.

2. Place a drain pan under the lower

radiator hose.

2. Add coolant until the level reaches

the MAX line on the coolant reser-

voir. Refer to Recommended En-

1. Radiator

gine Coolant. Use a funnel to

2. Oetiker clamp

avoid spillage. Do not overfiilll.

3. Lower radiator hose

3. Install a large hose pincher on the

lower radiator hose.

4. Remove the Oetiker clamp and

slowly disconnect the hose from

the radiator.

5. Remove the coolant reservoir

pressure cap.

3. Install the pressure cap.

4. Run the engine at idle with the

pressure cap on, allowing the front

cooling fans to cycle twice.

5. Depress the accelerator pedal five

(5) times to rev engine around

4000 RPM for 1-2 seconds.

6. Stop the engine and let it cool

down.

6. Wait until the coolant flow stops.

160

MAINTENANCE PROCEDURES

Cleaning the Muffler Spark Arrestor

WARNING

The muffler spark arrestor must be pe-

In order to avoid potentiall burns,

riodically purged of accumulated

do not remove the pressure cap or

carbon.

loosen the coollant drain plug if

the engine is hot.

CAUTION

Never perform thiis operatiion im-

7. Add coolant if necessary.

mediiately after the engiine has

8. After the next ride following this

been runniing, as the exhaust sys-

procedure, check the coolant level.

tem willl be very hot.

Add coolant as required. Refer to

Verifying the Engine Coolant

Level.

1. Remove the three hex head

screws that secure the exhaust

nozzle to its supports. Then re-

EXHAUST SYSTEM

move the exhaust nozzle.

Clleaniing the Area Surroundiing the

Exhaust System

WARNING

Debriis accumullatiion could llead to

a vehiiclle fiire when the exhaust

system is hot and the debris are

dried.

In some cases, that could result in

serious properly damages, iinju-

riies or even death.

Clean often and regullarly the area

EXHAUST NOZZLE SCREWS — RIGHT

surrounding the exhaust system

SIDE (TYPICAL)

when riidiing in swamp, bog, hay or

2. Pull the spark arrestor from the ex-

dead lleaves.

haust outlet pipe.

In other situations, cllean as per

maintenance schedulle

requiirement.

CAUTION

Never perform this operatiion iim-

mediately after the engine has

been running because exhaust

system is very hot.

1. From the rear of the vehicle, clean

1. Spark arrestor

the areas around the muffler.

2. Outlet pipe

2. Clean the areas around the ex-

haust pipe.

NOTICE

WARNING

Use a soft metalllic brush and be

carefull to avoid damagiing the

Clean allso under the heat shiellds.

spark arrestor mesh.

161

MAINTENANCE PROCEDURES

3. Remove carbon deposits from the

XPS Recommended Gearbox

spark arrestor using a brush.

DCT Oill

4. Inspect the spark arrestor mesh for

any damage. Replace as needed.

XPS full synthetic DCT Oil

5. Inspect the inside of the exhaust

outlet pipe. Remove any debris as

If the XPS product is not

needed.

availlablle

6. Place the spark arrestor back in-

side the outlet pipe.

Contact your authorized Can-Am

7. Apply a drop of threadlocker on ex-

Off-road dealer

haust nozzle screw threads.

Verifying the DCT Gearbox Oiil

Loctiite 243 (Bllue)

Level

1. Place the vehicle on a level

8. Position the exhaust nozzle on its

surface.

supports and tighten the screws to

specification.

NOTICE

To obtaiin a good levell readiing,

Tighteniing Torque

the vehicle must be horizontal in

Exhaust

24.5 ± 3.5 Nm

both directions (llaterally and

nozzle screws

(18 ± 2.5 lbf-in)

longitudinallly).

An anglled vehiclle allignment

causes iincorrect DCT gearbox oiil

GEARBOX

level readings and may influence

gearbox behaviior.

Recommended Gearbox DCT Oill

NOTICE

Please note that the gearbox Duall

Cllutch Transmiissiion system

(DCT) iis a high performiing, hiigh

maiintenance system whiich re-

quiires high quality and performing

oiil to function safely, properly and

to maintain iits expected llifecycle.

The gearbox DCT was developed

and vallidated using the XPS DCT

oiil.

VEHICLE ON LEVEL SURFACE

Damages caused usiing an oill

2. Select the PARK position.

which does not meet or exceed

3. Start the engine and let it idle for at

the XPS DCT oiil speciifiicatiions

least 1 minute.

may not be covered by BRP''s llim-

4. Stop the engine.

iited warranty.

5. Clean the area around the DCT

Do not use another type of oill

gearbox oil level plug.

when servicing.

162

MAINTENANCE PROCEDURES

NOTICE

Replace the O-ring if brittle or

damage.

Tightening Torque

DCT gearbox

5 ± 0.6 Nm

oil level plug

(44 ± 5 lbf-in)

11. Wipe off any spillage.

RIGHT-REAR WHEEL WELL

6. Remove the plug and the O-ring.

Changing the DCT Gearbox Oill and

Fiilter

1. Operate the vehicle for a few mi-

nutes to warm the DCT oil.

2. Place the vehicle on a level

surface.

NOTICE

To obtain a good llevel reading,

the vehiiclle must be horiizontal iin

both diirectiions (laterallly and

longiitudiinallly).

1. Oil level plug

An angled vehiicle aliignment willl

2. O-ring

cause an incorrect gearbox DCT

oiil llevell readiing and may iinfllu-

7. Check the oil level. It should be at

ence gearbox behaviior.

the top of the outermost thread of

the oil level hole.

3. Select the PARK position and stop

the engine.

OIL LEVEL

4. From underneath the vehicle,

8. To adjust the oil level, fill a syringe

clean the area around both drain

with the recommended oil. Refer to

plugs.

Recommended DCT Gearbox Oil.

9. Add oil through the hole until it

reaches the proper level.

10. Re-install the oil level plug and

tighten it to specification.

163

MAINTENANCE PROCEDURES

DRAIN PLUG OPENINGS

1. Oil filter cover

5. Place a drain pan under the gear-

2. Locking tie

box drain plugs.

3. Temperature sensor connector

6. Remove both magnetic drain

plugs. Discard the gasket rings

11. Remove the filter cover and dis-

and O-ring.

card the O-ring.

7. Clean the magnetic drain plugs of

metal shavings and residue.

NOTICE

The presence of fiine abrasiives is

acceptable.

8. Remove the screws that hold the

hydraulic valve and oil filter protec-

tive cover in place. Then remove

the cover.

1. Oil filter cover screws

2. Oil filter cover

3. O-ring (discard it)

4. Oil filter

12. Check and clean the areas around

the oil filter inlet and outlet.

RIGHT-REAR WHEEL WELL

9. Clean the area around the oil filter

cover.

10. Cut the locking tie and unplug the

temperature sensor connector.

1. Oil filter housing

2. Oil inlet orifice from vane pump

3. Oil outlet orifice

164

MAINTENANCE PROCEDURES

13. Remove the oil drain plug from the

Engine Oil

Gearbox Oil

hydraulic valve cover. Discard the

Filter

sealing ring.

1. Open end

(relief

valve)

1. Closed

“GEAR

end

BOX

ONLY”

indication

1. Oil drain plug

2. Sealing ring (discard it)

17. Install the new oil filter into its

housing.

14. Let the oil flow completely out of

18. Coat a new O-ring with DCT oil

the hydraulic housing.

and slip it onto the oil filter cover.

15. Re-install the hydraulic housing

19. Install the filter cover and tighten

drain plug with a new sealing ring

the screws to specification.

and tighten to specification.

Tightening Torque

Tiightening Torque

Filter cover

11 ± 1 Nm

Hydraulic

screws

(97 ± 9 lbf-in)

15 ± 2 Nm

housing drain

(133 ± 18 lbf-in)

plug

20. Connect the temperature sensor

and secure the cable to the con-

16. Apply a thin layer of DCT oil onto

nector housing with a locking tie.

the seal of the new gearbox oil

filter.

NOTICE

The engiine oiil fiilter and gearbox

oill fillter are simiilar. Do not con-

fuse them.

The engiine oiil fiilter has a closed

end, whereas the gearbox oill filter

is open at both ends. The gearbox

oill fillter has the “GEARBOX ON-

LY” marked on iit.

1. Oil filter cover

2. Locking tie

3. Temperature sensor connector

21. Install a new O-ring and gasket

rings on the gearbox drain plugs.

165

MAINTENANCE PROCEDURES

NOTICE

A miissing or damaged O-ring

could llead to internall leakiing of

the gearbox and subsequent DCT

oiil pressure failure.

22. Install the both gearbox drain

plugs and tighten them to

specification.

26. Fill a syringe with the recom-

Tighteniing Torque

mended DTC oil. Refer to Recom-

mended DCT Gearbox Oil.

Gearbox drain

30 ± 3 Nm

plugs

(22 ± 2 lbf-ft)

Gearbox DCT oil quantity

23. From the RH side of the engine,,

3 to 3.5 l

clean the area around the DCT

(3.17 to 3.7 qt (liq.,US))

gearbox oil level plug.

27. Add the oil through the filler plug

hole until the oil level reaches the

top of the outermost thread of the

oil level hole.

RIGHT-REAR WHEEL WELL

24. Remove the level plug and the

O-ring.

OIL LEVEL

28. Re-install the oil filler plug with a

new gasket ring and tighten it to

specification.

Tighteniing Torque

DCT Gearbox

30 ± 3 Nm

oil filler plug

(22 ± 2 lbf-ft)

29. Re-install the oil level plug and

1. Oil level plug

tighten it to specification.

2. O-ring

NOTICE

25. From the LH side of the engine, re-

Repllace the O-riing iif briittlle or

move the gearbox filler plug and

damage.

discard the gasket ring.

166

MAINTENANCE PROCEDURES

Changing the Diisconnect Uniit Oiil

Tightening Torque

1. Place the vehicle on a level

DCT gearbox

5 ± 0.6 Nm

surface.

oil level plug

(44 ± 5 lbf-in)

2. Select the PARK position and stop

the engine.

30. Wipe off any spillage.

3. Clean the area around the oil drain

31. Start engine and let it idle for at

plug.

least

minute, then check the

DCT oil level, refer to Verifying the

Gearbox DCT Oil Level.

32. Adjust the level if necessary.

33. Install the hydraulic valve filter pro-

tective cover.

Tiightening Torque

Hydraulic

valve filter

11 ± 1 Nm

protective

(97 ± 9 lbf-in)

cover screws

SKID PLATE REMOVED FOR CLARITY

Place a drain pan under the dis-

34. Dispose of the used oil and filter

connect unit drain plug area.

per

local

environmental

Remove the oil level plug.

regulations.

Allow the oil to drain completely.

Install the drain plug and tighten it

DISCONNECT UNIT

to specification.

Recommended Disconnect Unit Oill

Tightening Torque

NOTICE

Disconnect

2.5 ± 0.5 Nm

Do not filll the diisconnect uniit wiith

unit drain plug

(22 ± 4 lbf-in)

other type of oill than the recom-

mended one.

Remove the filler plug.

XPS Recommended Diisconnect

Unit Oill

5W40 Synthetic oil

If the recommended XPS engine oil is

not available:

- Use a 4-stroke SAE engine syn-

thetic oil meeting or exceeding the

following lubricant industry

Fill a syringe with the recom-

specifications

mended oil. Refer to Recom-

- Always check the API service label

mended Disconnect Unit Oil.

certification on the oil container, it

must contain the indicated

Disconnect Unit Oil Quantity

standards.

- API serviice classificatiion

65 ml

SN, and JASO MA2

(2.2 fl oz (US))

167

MAINTENANCE PROCEDURES

10. Install the filler plug and tighten it

to specification.

Tightening Torque

Disconnect

16.5 ± 2.5 Nm

unit filler plug

(146 ± 22 lbf-in)

11. Reinstall the central skid plate.

FRONT DIFFERENTIAL

Remove the plug and the O-ring.

Recommended Front Differentiall

Oiil

The XPS oil is specially formulated to

meet the lubrication requirements of

this differential. BRP strongly recom-

mends the use of its XPS oil.

NOTICE

Do not use another type of oill

when servicing.

Oil level plug

XPS Recommended Front

O-ring

Differentiall Oil

75W90 Synthetic gear oil

Check the oil level. It should be at

the top of the outermost thread of

Alternatiive iif XPS Product is not

the oil level hole.

Availlablle

75W90 (API GL-5) synthetic gear oil

Veriifyiing the Front Differentiall Oill

Levell

1. Park the vehicle on a level surface.

2. Select the PARK position and stop

the engine.

3. Clean the area around the front dif-

ferential oil level plug.

To adjust the oil level, fill a syringe

with the recommended front differ-

ential oil. Refer to Recommended

Front Differential Oil.

Add oil through the hole until it

reaches the proper level.

Inspect the oil level plug O-ring.

Replace if necessary

Re-install the oil level plug with the

O-ring and tighten to specification.

168

MAINTENANCE PROCEDURES

Tiightening Torque

Front

16.5 ± 2.5 Nm

differential oil

(146 ± 22 lbf-in)

level plug

10. Wipe off any spillage.

Changing the Front Diifferentiial Oiil

Place the vehicle on a level

surface.

Access hole

Select the PARK position and stop

Skid plate

the engine.

Drain plug

Clean the area around the oil level

plug.

Place a drain pan under the front

differential.

Access the drain plug through the

hole in the skid plate. Then remove

the drain plug and the O-ring.

Inspect the drainl plug O-ring. Re-

place if necessary

Once all of the oil has drained from

the front differential, install the

drain plug with the O-ring. Tighten

to specification.

Remove the oil level plug and the

Tightening Torque

O-ring.

Front

2.5 ± 0.5 Nm

differential

(22 ± 4 lbf-in)

drain plug

10. Using the recommended oil, refill

the front differential through the oil

level hole. Refer to Recommended

Front Differential Oil.

11. Ensure that the oil level reaches

the top of the outermost thread of

the oil level hole.

12. Inspect the oil level plug O-ring.

Replace if necessary

Oil level plug

13. Install the oil level plug with the

O-ring

O-ring. Tighten to specification.

From underneath the

vehicle,

Tightening Torque

clean the area around the drain

plug.

Front

16.5 ± 2.5 Nm

differential oil

(146 ± 22 lbf-in)

level plug

14. Wipe off any spillage.

169

MAINTENANCE PROCEDURES

REAR FINAL DRIVE

5. Check the oil level. The oil should

be level with the bottom of the

Recommended Final Drive Oill

hole.

6. To adjust the oil level, fill a syringe

The XPS oil is specially formulated to

with the recommended oil. Refer to

meet the lubrication requirements of

Recommended Final Drive Oil.

this final drive.

7. Add a small amount of oil through

the oil level hole until it reaches the

BRP strongly recommends the use of

bottom of the hole.

its XPS oil.

8. Inspect the oil level plug O-ring.

Replace if necessary

NOTICE

9. Install the oil level plug with the

Do not use another type of oill

O-ring and tighten to specification.

when servicing.

Tighteniing Torque

XPS Recommended Finall Driive

Oiil

Rear final

5± 0.6 Nm

drive oil level

(44 ± 5 lbf-in)

75W140 Synthetic gear oil

plug

If the XPS Product is not

Availlablle

Changiing the Rear Fiinal Drive Oill

1. Park the vehicle on a level surface.

Use a 75W140 synthetic gear oil

2. Select the PARK position and stop

that meets the API GL-5

the engine.

specification.

3. From the left side, clean the area

around the rear final drive oil level

plug.

Veriifyiing the Rear Fiinall Drive Oiil

Levell

1. Park the vehicle on a level surface.

2. Select the PARK position and stop

the engine.

3. From the left side, clean the area

around the rear final drive oil level

plug.

OIL LEVEL PLUG

4. From the right side, clean the area

around the magnetic drain plug.

4. Remove the rear final drive oil lev-

el plug and the O-ring.

170

MAINTENANCE PROCEDURES

10. Fill a syringe with the recom-

mended oil. Refer to Recom-

mended Final Drive Oil.

11. Add oil through the hole until the it

is level with the bottom of the hole.

12. Inspect the oil level plug O-ring.

Replace if necessary

13. Re-install the oil level plug with the

O-ring and tighten to specification.

Tightening Torque

MAGNETIC DRAIN PLUG — SKID PLATE

NOT SHOWN

Rear final

5± 0.6 Nm

5. Place a drain pan under the mag-

drive oil level

(44 ± 5 lbf-in)

netic drain plug area.

plug

6. Remove the magnetic drain plug

and discard the sealing ring.

BATTERY

NOTE:

Allow oil to flow completely out of the

Battery Maiintenance

final drive.

NOTICE

7. Remove the final drive oil level

Never charge a battery whiile iin-

plug and the O-ring.

stallled iin vehiclle.

8. Clean the magnetic drain plug of

metal shavings and residue.

These vehicles are equipped with a

VRLA battery (Valve Regulated Lead

NOTE:

Acid). It is a maintenance-free type

The presence of fine shavings is

battery, there is no need to add water

acceptable.

to adjust electrolyte level.

9. Install the magnetic drain plug with

NOTICE

a new sealing ring and tighten to

specification.

Never remove the battery sealiing

cap.

NOTICE

Never use a sealing riing a second

Battery Access

time. Allways repllace iit with a new

Access the battery through the service

one.

panel behind the driver’s seat. Refer

to Removing and Installing a Seat.

NOTE:

Allow oil to flow completely out of the

final drive before installing the plug.

Tiightening Torque

Rear final

30 ± 3 Nm

drive drain

(22 ± 2 lbf-ft)

plug

171

MAINTENANCE PROCEDURES

1. Service panel

1. Remove screws

2. Battery

2. Pull upward

3. Remove cap

Removiing the Battery

3. Pull upward on the holder, then re-

1. Remove the hex head screw and

move it.

lock washers that secure the black

4. Remove the positive terminal cap.

cable to the negative (-) terminal of

5. Remove the hex head screw and

the battery. Then disconnect the

lock washers that secure the red

cable.

cable to the positive (+) terminal of

the battery. Then disconnect the

NOTICE

cable.

Always respect thiis order for diis-

assemblly. Always disconnect the

BLACK (-) cablle fiirst.

6. Remove the battery.

Battery Clleaniing

2. Remove the two hex head screws

Clean battery, battery casing and bat-

and flat washers that secure the

tery posts using a solution of baking

battery holder to the bottom of the

soda and water.

battery compartment.

Remove corrosion from battery cable

terminals and battery posts using a

firm wire brush. Battery casing should

be cleaned by soft brush and baking

soda solution.

Installliing the Battery

1. Place

the

battery

its

compartment.

172

MAINTENANCE PROCEDURES

2. Connect the red cable to the posi-

5. Install the two battery holder re-

tive (+) terminal of the battery, us-

taining screws and flat washers.

ing the hex head screw and lock

Tighten to specification.

washers. Tighten to specification.

Tightening Torque

Battery holder

5 ± 1 Nm

retaining

(44 ± 4 lbf-in)

screws

6. Connect the black cable to the

negative (-) terminal of the battery,

using the hex head screw and lock

washers. Tighten to specification.

NOTICE

Allways respect this order for as-

semblly. Always connect the RED

(+) cablle fiirst.

Tiightening Torque

Positive

5.0 ± 0.5 Nm

terminal

(44 ± 4 lbf-in)

Tightening Torque

screw

Place the protective cap over the

Negative

5.0 ± 0.5 Nm

positive terminal.

terminal

(44 ± 4 lbf-in)

Position the battery holder on the

screw

battery. Ensure that the top part of

the holder is properly engaged in

FUSES

its slot.

Repllaciing a Fuse

If a fuse is burnt, replace it by one of

the same rating.

NOTICE

Do not use a hiigher rated fuse as

this can cause severe damage.

1. To open the fuse box, remove the

O-rings installed on both locks.

Place positive terminal cap

Engage holder in slot

Install screws and washers

173

MAINTENANCE PROCEDURES

2. Press both tab against the cover

and pull it upwards.

Fusible Links

Fuse Box and Fuse Hollder

There are two fusible links on the ve-

Locations

hicle. One of them is located near the

front fuse box.

Front Fuse Box

The front fuse box is located under the

front fuse box cover in the center of

the dashboard.

The other one is located under the

center console.

FRONT FUSE BOX COVER

In the event that a fusible link blows,

FRONT FUSE BOX

see your Can-Am Off-Road dealer.

Fuse Holders

Rear Fuse Boxes

The fuse holders are also located

The rear fuse boxes are located on

under the front fuse box cover, next to

the rear baffle cover behind the driv-

the front fuse box.

er’s seat. These include the engine

fuse box and the vehicle fuse box.

174

MAINTENANCE PROCEDURES

Fuse Holders

RAT

No.

DESCRIPTION

ING

DPS

40 A

10.25in Color

Touchscreen

F29

20 A

Display (if

equipped

1. Rear baffle cover

2. Engine fuse box

Rear Fuse Box - Vehicle

3. Vehicle fuse box

Rear Fuse Box - Vehiclle

Fuse Box and Fuse Holder

RAT

Descriptions

No.

DESCRIPTION

ING

Front Fuse Box

Relay Speedo

10 A

Front Fuse Box

Coil/SS1-SS2

10 A

RAT

No.

DESCRIPTION

ING

ECM

10 A

Key switch/Clock

10 A

Sensor and

10 A

switch light

EVAP/Coil Relay

F18

10 A

Fan

F11

Headlamp

10 A

F22

BCM SAS

20 A

F12

DC1-DC3

10 A

F23

BCM Smart Lock

20 A

F14

ACC post

20 A

F28

Fuel Pump

10 A

F16

Taillamp

10 A

F34

Main Relay Lamp

25 A

BCM SAS (if

F22

20 A

equipped)

Inj - Speed

F35

sensor - Oxygen

10 A

F23

BCM Smart Lock

20 A

sensor

Accessory relay

—

Rear Fuse Box - Engine

Headlamp relay

—

Rear Fuse Box - Engine

BRK relay

—

RAT

No.

DESCRIPTION

ING

Fuse Holders

Engine Fan 1

10 A

Engine Turbo

F17

25 A

Intercooler Fan 1

175

MAINTENANCE PROCEDURES

Rear Fuse Box - Engine

RAT

No.

DESCRIPTION

ING

F27

Gearbox ACT

25 A

F30

Gearbox Fan 1

15 A

F31

Gearbox Fan 2

15 A

F32

Intercooler Fan 2

25 A

2. Turn adjustment screws to adjust

beam height to your convenience.

F33

Engine Fan 2

10 A

The beam aiming screw is located

Engine Fan relay

—

under the headlight module.

Engine Main

NOTE:

—

relay

Adjust left and right headlights evenly.

Engien Turbo

R10

Intercooler1 relay

Fusible Links

Fusible Liinks

RAT

No.

DESCRIPTION

ING

FL-1

Fuse link 1

14 AWG

FL-2

Fuse link 2

14 AWG

SPARK PLUGS

Spark Plug Access

LIGHTS

To access the spark plugs, the inter-

Light Bulb Replacement

cooler must be removed.

No bulb replacement is required for

1. Disconnect the two intercooler fan

this vehicle.

connectors. Then remove the fan

harness from its plastic hooks.

It is equipped with LEDs (Light Emit-

ting Diode) lights. This technology has

proven itself to be very reliable.

In the unlikely event that one light

does not work, have it checked by an

authorized Can-Am Off-road dealer,

repair shop or person of your own

choosing.

Headllight Beam Aiiming

1. Remove the headlight cover.

176

MAINTENANCE PROCEDURES

3. Remove the plastic rivet on the top

of the air intake grille.

RIGHT-REAR WHEEL WELL

1. Fan connectors

2. Fan harness

4. Pull towards the front to remove

3. Plastic hooks

the air intake grille.

2. Loosen the hose clamps on the left

and right intercooler hoses. Then

disconnect the hoses from the

intercooler.

5. Remove the plastic rivets and

screws that secure the air intake

assembly to the cargo rack. Then

remove the air intake assembly.

LEFT-REAR WHEEL WELL

1. Hose clamp

2. Left intercooler hose

3. Intercooler

1. Air intake assembly

2. Plastic rivets

3. Screws

6. Remove the screws and flat wash-

RIGHT-REAR WHEEL WELL

ers from the cargo rack. Then re-

1. Hose clamp

move the cargo rack.

2. Right intercooler hose

3. Intercooler

177

MAINTENANCE PROCEDURES

10. Remove the screws from the inter-

7. Remove the screws that retain the

cooler support. Then remove the

acoustic baffles to the intercooler

intercooler.

support and the chassis. Then re-

move the baffle from each side of

the intercooler.

The spark plugs are now accessible.

When re-installing the above-men-

ACOUSTIC BAFFLE - LEFT - TYPICAL

tioned components, pay attention

8. Remove the screw and flat washer

the following:

that retain the coolant reservoir to

the intercooler support. Then move

Tiightening Torques

it aside.

Intercooler

6 ± 0.5 Nm

hose clamps

(53 ± 4 lbf-in)

Air intake

2.5 ± 0.5 Nm

assembly

(22 ± 4 lbf-in)

screws

Cargo rack

3.5 ± 0.5 Nm

screws

(31 ± 4 lbf-in)

Acoustic baffle

8 ± 1 Nm

9. On LH side, detach the air filter in-

screws (into

(71 ± 9 lbf-in)

take hose from the side baffle.

chassis)

Acoustic baffle

screws (into

5.5 ± 0.5 Nm

intercooler

(49 ± 4 lbf-in)

support)

178

MAINTENANCE PROCEDURES

Tighteniing Torques

Coolant

4.5 ± 0.5 Nm

reservoir screw

(40 ± 4 lbf-in)

Air intake hose

6 ± 0.5 Nm

clamp

(53 ± 4 lbf-in)

Intercooler

8 ± 1 Nm

support screws

(71 ± 9 lbf-in)

1. Approved socket

Removing the Spark Pllug

2. Improper socket

1. Disconnect the ignition coil

connector.

5. Clean the spark plug hole using

2. Remove the ignition coil screw.

pressurized air.

6. Remove the spark plug.

7. Use ignition coil as a puller to ex-

tract the spark plug from its hole.

3. Remove ignition coils with gaskets

from spark plug by rotating coil

side to side as you pull up.

NOTICE

Inspectiing the Spark Plug

Do not pry on iigniitiion coiil with a

1. Using a feeler gauge, inspect elec-

tooll.

trode gap as specified.

Spark Plug

Manufacturer

NGK

and type

SILMAR9F7

0.6 - 0.7 mm

Electrode gap

(.024 - .028 in)

NOTICE

Replace spark pllug iif out of

speciificatiion.

4. Using a spark plug socket, release

the torque applied to the spark

plug.

179

MAINTENANCE PROCEDURES

Troubleshooting a Fouled Spark

2. Hand screw spark plug into cylin-

Plug

der head, then tighten with a tor-

que wrench and an appropriate

1. Fouling of the spark plug is indi-

socket.

cated by irregular running or misfir-

ing of the engine, decreased

Tighteniing Torque

engine speed due to misfiring, re-

duced performance, and increased

14 ± 1 N∙m

fuel consumption.

Spark plug

(124 ± 9 lbf∙in)

2. Other possible causes are: use of

an incorrect or bad fuel, defective

3. Install ignition coil and plug the

ignition system, incorrect spark

connector.

plug gap, loss of compression, or

lubricating oil entering the combus-

Tighteniing Torque

tion chamber.

3. The plug face of a fouled spark

Ignition coil

9 ± 1 N∙m

plug has either a wet or dry black

screw

(80 ± 9 lbf∙in)

carbon deposit. Such coatings

form a conductive connection be-

tween the center electrode and the

DRIVE SHAFT BELLOWS

ground electrode.

Inspecting the Drive Shaft Bellow

Spark Pllug Anallysiis

1. Visually inspect drive shaft bellows

conditions.

2. Check bellows for cracks, tears,

leaking grease, etc.

3. Replace damaged bellows as

necessary.

WHEEL BEARING

TYPICAL

Inspecting the Wheell Bearing

1. Overheated (light gray, white)

1. Lift and support vehicle.

2. Normal (light brown, brown)

2. Push and pull the wheel from the

3. Fouled

(black, wet or dry, dark deposits,

upper edge to feel the play.

gray, melted coating)

The plug face reveals the condition of

the engine, operating condition, meth-

od of driving and fuel mixture. For this

reason it is advisable to inspect the

spark plug at prescribed intervals, ex-

amining the plug face (i. e. the part of

the plug projecting into the combus-

tion chamber).

Installling the Spark Pllug

1. Prior to installation make sure that

3. See an authorized Can-Am Off--

contact surfaces of the cylinder

road dealer, a repair shop or per-

head and spark plug are free of

son of your choosing if there is

grime.

abnormal play.

180

MAINTENANCE PROCEDURES

WHEELS AND TIRES

Tiire Pressure

WARNING

Removing a Wheel

Tire pressure greatly affects ve-

1. Loosen nuts then lift and support

hiiclle handliing and stabiiliity.

vehicle.

Insufficient pressure may cause

2. Remove lug nuts then remove

tiire to defllate and rotate on wheell.

wheel.

Overpressure may burst the tiire.

Always folllow recommended

Installliing a Wheel

pressure.

1. Make sure the wheel studs are

NEVER set tire pressure bellow

free of any dirt or metal chips.

minimum. It could cause the tiire to

diisllodge from the riim.

WARNING

Do not use any type of llubriicant

Check pressure when tires are colld

on the studs or lug nut threads be-

before using the vehicle. Tire pressure

fore tiightening.

changes with temperature and alti-

tude. Recheck pressure if one of

these conditions has changed.

2. Lift the wheel onto the studs.

3. Install the wheel lug nuts and tight-

Refer to the Tires Pressure and Maxi-

en by hand until snug.

mum Load Label on your vehicle for

applicable pressure.

NOTICE

NOTE:

Allways use the recommended

Although the tires are specifically de-

wheell lug nuts for the type of

signed for off-road use, a flat may still

wheell. Using a different lug nut

occur. Therefore, it is recommended

coulld cause damages to the riim

to carry a tire gauge, tire pump and a

or studs.

repair kit.

Tighten to the specified torque, us-

Inspectiing a Tire

ing the sequence shown below.

1. Check tire for damage and wear.

2. Replace if necessary.

Tiightening Torque

Tiire Replacement

Wheel lug

120 ± 5Nm

nuts

(88.5 ± 4 lbf-ft)

Tire replacement should be performed

by an authorized Can-Am Off-road

dealer, a repair shop or a person of

your choosing.

WARNING

Replace tiires only with the same

type and size as origiinall tires.

For uniidiirectiional tread pattern,

ensure that the tires are iinstallled

in the correct directiion of rotatiion.

Tires should be repllaced, by an

experienced person, in accord-

ance wiith tire iindustry standards

and toolls.

181

MAINTENANCE PROCEDURES

Tiire Mountiing on Beadlock Wheells

1. Mount the tire on the wheel:

1. On the opposite side of the

beadlock, apply tire mounting

lube on both bead of the tire

and wheel to ensure that it

proper seating during inflation.

Mount the inner bead over the

wheel.

2. Seat the tire outer bead in the

shoulder of the beadlock inner

TYPICAL - TIGHTENING SEQUENCE

ring and center the tire.

Tighteniing Torque

NOTICE

Beadlock

The diifference between the smalll-

screws

14 ± 1 Nm

est gap and the biggest gap

(SECOND

(124 ± 9 lbf-in)

should not exceed 3 mm (1/8 in).

TORQUE)

1. Tire outer bead

TYPICAL - TIGHTENING SEQUENCE

2. Beadlock inner ring shoulder

4. At this time, check whether the tire

2. Install all of the beadlock screws.

is still centered on the wheel. Re-

To avoid cross-threading, start the

position it if necessary.

screws by hand.

5. Torque the beadlock screws a

3. Tighten the beadlock screws per

third time, using the same

the following specification and

sequence:

Tighteniing Torque

NOTE:

To ensure even pressure on the bead-

Beadlock

lock clamp ring, tighten the screws a

screws

29 ± 1 Nm

few turns at a time.

(THIRD

(21 ± 1 lbf-ft)

TORQUE)

Tighteniing Torque

Beadlock

4 ± 1 Nm

screws (FIRST

(35 ± 9 lbf-in)

TORQUE)

182

MAINTENANCE PROCEDURES

2. Check the tire position on the

wheel and reposition it if

necessary.

3. Restart the torquing sequence

described above.

Torque the beadlock screws a fi-

nall time, following the indicated

sequence:

Tightening Torque

TYPICAL - TIGHTENING SEQUENCE

Beadlock

29 ± 1 Nm

screws (FINAL

(21 ± 1 lbf-ft)

NOTE:

TORQUE)

The beadlock clamp ring should be in

contact with the beadlock inner ring.

The beadlock clamp ring can flex

slightly to match the tire bead. THIS IS

NORMAL.

6. Verify the gap between the tire and

the beadlock clamp ring. It should

be approximately equal all around

the ring.

NOTICE

The difference between the smalll-

TYPICAL

FINAL

TIGHTENING

est gap and the biiggest gap

SEQUENCE

shoulld not exceed 3 mm (1/8 iin).

9. Inflate the tire to seat the inner

bead on the wheel. Always employ

best practices, such as using a tire

safety cage.

WARNING

Never exceed the tiire’’s recom-

mended maxiimum pressure for

seatiing beads.

SUSPENSION

Tire

Inspectiing the Suspension

Beadlock clamp ring edge

See an authorized Can-Am Off-road

dealer, a repair shop or a person of

Gap equal all around beadlock clamp ring

your choosing if any problem is

detected.

If the gap is not acceptable, pro-

ceed as follows:

Shock Absorbers

1. Loosen all of the screws.

1. Inspect shock absorber for leaks,

bump stop wear out or other

damages.

183

MAINTENANCE PROCEDURES

2. Verify if fasteners are still well

Stabiiliizer Bar

tightened.

1. Check stabilizer bars for cracks,

bending or, other damaged.

Tighteniing Torque

Lubricating the Suspensiion

140 ± 10 Nm

M14 bolt

(103 ± 7lbf-ft)

Stabiiliizer Bar

1. Lubricate stabilizer bars using the

Front Suspension Arms

following product.

1. Check suspension arms for

cracks, bending or other damages.

XPS synthetic suspensiion

2. Re-tighten the suspension arm

grease

bolts to specifications at ride

height.

Stabiiliizer Bar Grease Fitting

Locatiions

NOTICE

There is a grease fitting under each

To avoid suspensiion bushings

front stabilizer bar bushings.

damages, never llift the vehiicle

from the ground to re-tighten sus-

pension arm fasteners.

When possible, always applly the

tiightening torque by the bollt head

and not by usiing the nut to ensure

optimall cllamping.

Tighteniing Torque

185 ± 5 Nm

M14 bolt

(136 ± 4 lbf-ft)

FRONT RH SIDE SHOWN- BEHIND THE

FRONT RADIATOR

Rear Suspensiion Arms

There is also a grease fitting on each

1. Check trailing arms for distortion,

of the rear stabilizer bar bushings.

cracks or bending.

2. Re-tighten

trailing

arms to

specifications.

NOTICE

The suspension arms must be

tiightened on the M14 bolt head

and not on the nut (when possi-

blle) to iinsure optiimal clampiing.

Tighteniing Torque

REAR STABILIZER BAR - LEFT SIDE -

All M14

170 ± 20 Nm

TYPICAL

bolts)

(125 ± 157 lbf-ft)

184

MAINTENANCE PROCEDURES

BRAKES

NOTICE

Verifying the Brake Flluid Level

Ensure filller cap diiaphragm is

pushed iinsiide the cap before

Place the vehicle on a level

cllosiing the brake flluid reservoir.

surface.

Remove the fuse box cover.

Remove the front service cover.

Ensure filler cap diaphragm is

pushed inside the cap before clos-

ing the brake fluid reservoir.

Tightening Torque

0.75 ± 0.2 Nm

Filler cap

(6.6 ± 1.8

screws

lbf-in)

Recommended Brake Flluid

Always use brake fluid meeting the

Fuse box cover

specification DOT 4 only.

Front service cover

NOTICE

Using the marks on the brake fluid

reservoirs, check the fluid level.

To avoid serious damage to the

The proper level should be be-

braking system, do not use flluids

tween the LOWER and UPPER

other than the recommended one,

lines.

nor miix diifferent flluiids for toppiing

up.

Do not use brake fluid taken from

olld or allready opened containers.

Brake Inspection

The brake inspection, maintenance

and repair should be performed by an

authorized Can-Am dealer, a repair

shop or person of your choosing.

However, verify the following between

visits to your dealer:

BRAKE FLUID RESERVOIRS - FROM PAS-

SENGER SIDE

- Brake fluid level

- Brake system for fluid leaks

NOTE:

- Brake pad wear

A low fluid level may indicate a leak or

- Brake cleanliness

worn brake pads.

WARNING

Adding Brake Fluiid

The brake flluiid repllacement or

1. Clean filler cap before removing.

brake system maiintenance and

2. Add fluid as required. Do not

repairs shoulld be performed by an

overfiilll.

authoriized Can-Am dealler.

3. Close filler cap and tighten its

screws to specification.

185

MAINTENANCE PROCEDURES

SEAT BELTS

Cleaning a Seat Belt

1. Sponge the straps with mild soap

and water to clean dirt and debris

from the seat belts.

WARNING

Do not use pressure washer to

cllean seat belt components. Use

of pressure washer can perma-

FRONT LATERAL FASTENERS - TYPICAL

nently damage seat belt

components.

Tighteniing Torque

M12 x 30

110 ± 10 Nm

NOTICE

screws

(81 ± 7 lbf-ft)

Do not use bleach, dye, or house-

holld detergents.

3. Tighten the rear lateral fasteners

to specification.

CAGE

Tiightening the Cage Fasteners

The tightness of the cage fasteners

must be periodically checked.

1. Tighten the front fasteners to

specification.

REAR LATERAL FASTENERS - TYPICAL

Tighteniing Torque

M12 x 30

110 ± 10 Nm

screws

(81 ± 7 lbf-ft)

4. Tighten the rear fasteners to

specification.

FRONT FASTENERS - TYPICAL

Tighteniing Torque

M12 x 60

110 ± 10 Nm

screws

(81 ± 7 lbf-ft)

2. Tighten the front lateral fasteners

to specification.

186

VEHICLE CARE

Vehicle Cleaning and

with fresh water is necessary to pre-

serve vehicle and its components

Protection

after each operating day.

NOTICE

Painted parts which are damaged

When usiing a high pressure

should be properly repainted to pre-

washer to clean the vehiiclle, pro-

vent rust.

ceed carefullly around seats, ellec-

triicall components and decalls.

When required, wash the body with

Also maintain a good distance be-

warm water and soap (only use mild

tween the nozzle and the surface

detergent). Apply non-abrasive wax.

beiing washed.

NOTICE

Pay attention to certain areas where

Never clean pllastic parts with

salt-water, mud or debris can accumu-

strong detergent, degreasiing

late and potentially cause:

agent, paiint thinner, acetone, etc.

- Fire

- Wear

Protect the vehicle with a cover to pre-

- Interference

vent dust accumulation during

- Corrosion.

storage.

This list includes but is not limited to:

NOTICE

- Around exhaust system and be-

The vehiclle has to be stored in a

tween muffler and muffler cover

cooll and dry place and covered

- Under and around the fuel tank

with an opaque tarpaullin. This wiilll

- Radiator

prevent sun rays and griime from

- Shock absorbers

affectiing pllastic components and

- Around front and rear differentials

- Around and underneath engine

vehiiclle fiinish.

and gearbox

- Inside wheels

- On top of skid plates.

WARNING

Debris accumulation coulld lead to

a vehicle fire when the exhaust

system iis hot and the debriis are

driied.

In some cases, that coulld result iin

serious properlly damages, injju-

ries or even death.

Cllean often and regularlly the area

surroundiing the exhaust system

when riding iin swamp, bog, hay or

dead leaves.

In other situatiions, clean as per

maiintenance schedule

requirement.

When vehicle is used in salt-water or

mud environment rinsing the vehicle

188

STORAGE AND PRESEASON PREPARATION

When a vehicle is not in use for more

Before using your vehicle after stor-

than 4 months, proper storage is a

age, a preparation is required.

necessity.

See an authorized Can-Am Off-road

If the vehicle is to be remain inactive

dealer, a repair shop, or a person of

for more than 21 days, disconnect the

your own choosing to have your ve-

BLACK (-) cable of the battery.

hicle prepared properly.

The use of a low amperage trickle

charger is recommended to keep bat-

tery fully charged.

While reading this Operator’s Guide, remember that:

WARNING

Indicates a potential hazard which, if not avoided, could result

in serious injury or death.

189

VEHICLE IDENTIFICATION

The main components of your vehicle

The vehicle is also equipped with an

(engine and frame) are identified by

engraved VIN on the frame. It is lo-

different serial numbers. It may some-

cated on the right lower front member

times become necessary to locate

of the frame, just below the front

these numbers for warranty purposes

differential.

or to trace your vehicle in the event of

loss.

These numbers are required by the

authorized Can-Am Off-road dealer to

complete warranty claims properly.

We strongly recommend that you take

note of all the serial numbers on your

vehicle and supply them to your insur-

ance company.

Vehicle Identification Number

Engine Identification Number

The VIN label is located on the panel

under the glove box.

The engine serial number plate is lo-

cated on the right of the engine near

the engine oil filter housing.

Transmission Identification

NRMM Models

Number

The transmission identification num-

ber plate is located on the LH side of

the gearbox, near the final drive.

All Other Models

192

TECHNICAL INFORMATION LABELS

Verifying the Engine Oil Level

CAUTION

Find and folllow the procedure iindicates in the operator’’s guiide.

The engine of thiis SSV has been develloped and valiidated usiing the

BRP XPS Synthetic 4-stroke oiil.

Engine oil and certaiin components iin the engine compartment may be

hot. Diirect contact may resullt in skiin burn.

1. The engiine MUST be at operation temperature.

2. Vehiclle must be levell to perform veriificatiion.

3. Let the engiine run at idle for at lleast 20 seconds.

4. Stop the engine and wipe the diipstick.

5. Screw diipstick in completely before checkiing the oill level.

North American Models

Models Outside North America

196

RADIO FREQUENCY DIGITALLY ENCODED

SECURITY SYSTEM (RF D.E.S.S. KEY)

This device complies with FCC Part 15 and Industry Canada license exempt

RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IC Registration Number: 12006A-1001317030

FCC ID: 2ACER-1001317030

We, the party responsible for compliance, declare under our sole responsibility

that the device is in conformity with the provisions of the following Council Direc-

tive: 2014/53/EU. To which this declaration relates is in conformity with the es-

sential requirements and other relevant requirements. The product is in

conformity with the following directives, harmonized standards and regulations:

Radio Equipment Directive (RED) 2014/53/EU and Harmonized Standards:

- IEC 62368-1:2014, CISPR 25:2016, ISO 11452-2:2004, ETSI EN 300 330

V2.1.1:2017

Radio Equipment Statutory Instrument 2017/1206 and Designated Standards:

- IEC 62368-1:2014, CISPR 25:2016, ISO 11452-2:2004, ETSI EN 300 330

V2.1.1:2017

199

EVAPORATIVE EMISSION CONTROL SYSTEM

Caliifornia Models with Evaporative Emiissiion Control System

Beginning with the 2018 model-year vehicles, some California models are certi-

fied to meet the CARB (California Air Resources Board) TP-933. These models

are equipped with an evaporative emission control system consisting of a low

permeation fuel tank (LPFT), low permeation fuel lines (LPFL) and an actively

purged carbon canister.

The following statement is required by the CCR (California Code of Regulation):

An add-on or modified part must be compliant with applicable ARB evaporative

emission control standards. A violation of this requirement is punishable by civil

and/or criminal punishment.

200

NOISE EMISSION CONTROL SYSTEM

REGULATION

(CANADA AND UNITED STATES)

USA and Canada Only

Tampering wiith Noise Control System Is Prohibiited!

U.S. Federal law and Canadian provincial laws may prohibit the following acts or

the causing there of:

1. The removal or rendering inoperative by any person other than for purposes

of maintenance, repair or replacement of any device or element of design in-

corporated into any new vehicle for the purpose of noise control prior to its

sale or delivery to the ultimate purchaser or while it is in use or

2. The use of the vehicle after such device or element of design has been re-

moved or rendered inoperative by any person.

Among those Acts Presumed to Constiitute Tampering Are the Acts Listed

Below:

1. Removal or alteration or the puncturing of the mufflers or any engine compo-

nent which conducts removal of engine exhaust gases.

2. Removal or alteration or the puncturing of any part of the intake system.

3. Replacing any moving parts of the vehicle or parts of the exhaust or intake

system, with parts other than those specified by the manufacturer.

4. Lack of proper maintenance.

201

DECLARATION OF CONFORMITY

UK Declaration of Conformity

565 de la Montagne Street

Valcourt (Québec) J0E 2L0

Canada

www.brp.com

UK Declaration of Conformity

Authorized Representative

: BRP Recreational Products UK Ltd.,

Castle Chambers, 43 Castle Street, Liverpool, L2 9SH

This declaration of conformity is issued under the sole responsibility of the manufacturer.

The undersigned, representing the manufacturer, hereby declares that model year 2024 Side

by Side Vehicles marked with the

mark and a 17-character vehicle identification number

(VIN) structured as

3JBxxxxxxRxxxxxxx under commercial name Can-Am Maverick R

comply with all the relevant provisions of the following Statutory Instruments:

Supply of Machinery (Safety) Regulations 2008, UK

ISO 12100:2010 &

SI 2008/1597 as amended up to and including SI

EN 16990:2020

2020/1112

Non-Road Mobile Machinery (Type-Approval and

Category ATS,

Emission of Gaseous and Particulate Pollutants)

Stage V emission limits

Regulations 2018, UK SI 2018/764 as amended up

to and including SI 2020/1393

Electromagnetic Compatibility Regulations 2016, UK

CISPR 12:2007/A1:2009 &

SI 2016/1091 as amended up to and including SI

IEC 61000-6-1:2007 or

2020/1112

UN R10.04 or later version

Batteries and Accumulators (Placing on the Market)

EN 50342-7:2015

Regulations 2008, UK SI 2008/2164 as amended up

to and including UK SI 2020/904

Radio Equipment Regulations 2017, UK SI

Art. 3.1a: IEC 62368-1:2014

2017/1206 as amended up to and including SI

2020/1112

Art. 3.1b: CISPR 25:2016 &

ISO 11452-2:2004

(If fitted with radio frequency (RF) D.E.S.S. key)

Art. 3.2: ETSI EN 300 330

V2.1.1:2017

_____________________________

Luc Bouchard, Eng.

Valcourt, QC, Canada

Director, Product Development, Can-Am SSV

Bombardier Recreational Products Inc.

204

TECHNICAL SPECIFICATIONS

Lubriication System

Type

Dry sump

Replaceable cartridge

Oil filter

oil filter

2.8 l

Capacity

(3 qt (liq.,US))

General purpose

5W40 Synthetic oil

Recommend

Cold temperature

0W40 Synthetic oil

ed XPS oil

Warm

10W50 Synthetic oil

temperature

Use a 4-stroke SAE

Engine oil

engine synthetic oil

meeting or exceeding

the following lubricant

industry specifications.

Always check the API

If the XPS products is not

service label certification

available

on the oil container, it

must contain the

indicated standards.

- API serviice

cllassifiication SN,

and JASO MA2

Transmissiion

7-gears Dual Wet

Type

Clutch Transmission

(DCT)

Automatic gear select

Shift mode

mode and manual shift

mode (paddles)

Low and High ranges on

Gear selection

the fly activation

Available driving modes

(normal/Sport/Sport+)

209

TECHNICAL SPECIFICATIONS

Gearbox

Dual range (HI-LO) with

Type

PARK, neutral and

reverse

3 to 3.5 l

Refill

(3.17 to 3.7 qt (liq.,US))

Capacity

4.9 l

New or renew

(5.2 qt (liq.,US))

Gearbox oil

XPS full synthetic DCT

Recommended XPS oil

Oil

If the XPS products is not

Contact your authorized

available

Can-Am Off-road dealer

VEHICLE

Intake System

Donaldson high

Air filter

performance filter

Exhaust System

Catalyst + Spark

NRMM models

arrestor

Exhaust system

Spark arrestor approved

Other models

by USDA Forest Service

Cooliing System

Main front radiator with

Type

rear dual fan

intercoolers

Extended life pre-mixed

Recommended XPS coolant

coolant

Ethyl glycol / water mix

Coolant

(50%/50%).

If the XPS products is not

or coolant specifically

available

designed for aluminum

engines

8.7 l

Capacity

(2.3 gal (liq.,US))

210

TECHNICAL SPECIFICATIONS

Ellectrical System

Magneto generator output

1 700 W

Quantity

Make and type

NGK SIMLAR9F7

Spark plug

0.6 to 0.7 mm

Gap

(0.023 to 0.028 in)

Type

Maintenance free SLA

Voltage

12 volts

Battery

Nominal rating

20 A•h

Power starter output

800 W

Headlight

LEDs

Taillight

LEDs

Signature lights

LEDs

Refer to Fuses in

Fuses

Maintenance

Rear

Camera

X rs

Front and rear

Fuel System

Electronic fuel injection

Fuel delivery

(EFI)

Fuel pump

Type

Electric (in fuel tank)

Injectors

2 by cylinder

Throttle body

54 mm

Premium unleaded

Type

gasoline - Refer to Fuel

Requirements

Fuel

North America

91 AKI (R+M)/2

Recommend

ed Octane

Outside North

rating

95 RON

America

211

TECHNICAL SPECIFICATIONS

Driive System

Spiral bevel gear

Front drive

Lockable front differential

with exclusive Smart-Lok

Front drive ratio

3.6:1

350 ml

Capacity

(11.8 fl oz (US))

Front differential

Recommended XPS differential

XPS 75W90 Synthetic

oil

gear oil

If the XPS products is not

Synthetic gear oil 75W90

available

API GL-5

Spiral bevel gear / Final

Rear final drive

drive

Rear final drive ratio

4.09:1

500 ml

Capacity

(17 fl oz (US))

Rear final drive

XPS 75W140 Synthetic

Recommended XPS final drive oil

oil

gear oil

If the XPS products is not

Synthetic gear oil

available

75W140 API GL-5

65 ml

Capacity

(2.2 fl oz (US))

Recommended XPS final drive oil

5W40 Synthetic oil

Use a 4-stroke SAE

engine synthetic oil

meeting or exceeding the

following lubricant

Disconnect unit

industry specifications.

Always check the API

If the XPS products is not

service label certification

available

on the oil container, it

must contain the

indicated standards.

- API service

cllassification SN,

and JASO MA2

CV joint grease

Steering

Center take-off rack and

Type

pinion

Telescopic adjustable

Steering wheel

tilt steering

213

TROUBLESHOOTING GUIDELINES

1. "–" IS DISPLAYED ON THE GEARBOX POSITION

DISPLAY

Electrical communication error.

- Contact an authorized Can-Am Off-road dealer.

2. ENGINE DOES NOT TURN

D.E.S.S. key is not installed on D.E.S.S. post.

- Securely install key to D.E.S.S. post.

Burnt fuse.

- Check fuses.

Weak battery or loose connections.

- Check charging system fuse.

- Check fault message in digital display.

- Check battery connections and terminals condition.

- Have the battery checked by an authorized Can-Am Off-road dealer.

Defective engine start button.

- Contact an authorized Can-Am dealer.

Defective starter solenoid.

- Contact an authorized Can-Am dealer.

D.E.S.S. key not recognized is displayed in the multifunction gauge.

- Clean D.E.S.S. key.

3. ENGINE TURNS OVER BUT FAILS TO START

Flooded engine (spark plug wet when removed).

(If the engine does not start and it is fuel-flooded, the drowned mode can

be activated to prevent fuel injection and to cut ignition while cranking.

Proceed as follows:

• Install key on D.E.S.S. post.

• Press completely and HOLD accelerator pedal.

• Press the engine START button.

The engine should be cranked for 10 seconds. Release engine START

button.

Release accelerator pedal and start/crank engine again to allow starting.

If it does not work:

• Remove the spark plugs (tools are supplied in tool kit). Refer to Spark

Plugs in Maintenance Procedures.

• Crank engine several times.

• Install new spark plugs if possible or clean and dry spark plugs.

• If engine does not start, seek service from an authorized Can-Am dealer,

repair shop, or person of your own choosing for maintenance, repair, or

replacement. Please refer to the US EPA Emission-Related Warranty con-

tained herein for information about warranty claims.

No fuel to the engine (spark plug dry when removed).

- Check fuel tank level.

- Check fuel pump fuse.

224

TROUBLESHOOTING GUIDELINES

- Obstructed fuel pump pre-filter or fuel pump failure. Seek service from an

authorized Can-Am dealer, repair shop, or person of your own choosing

for maintenance, repair, or replacement. Please refer to the US EPA

Emission-Related Warranty contained herein for information about war-

ranty claims.

Spark plug/ignition (no spark).

- Check ignition fuse.

- Remove spark plug then reconnect to ignition coil.

- Start engine with spark plug grounded to the engine away from spark plug

hole. If no spark appears, replace spark plug.

- If trouble persists, seek service from an authorized Can-Am dealer, repair

shop, or person of your own choosing for maintenance, repair, or replace-

ment. Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

4. ENGINE LACKS ACCELERATION OR POWER

Seat belt not buckled properly. Check cluster message.

- Buckle up seat belt.

Fouled or damaged spark plug.

- Replace spark plugs.

Engine air filter plugged or dirty.

- Check air filter and replace if necessary.

- Check deposits in engine air filter housing.

Lack of fuel

- Dirty or clogged fuel pump pre-filter. Seek service from an authorized

Can-Am dealer, repair shop, or person of your own choosing for mainte-

nance, repair, or replacement. Please refer to the US EPA Emission-Re-

lated Warranty contained herein for information about warranty claims.

Engine is in Torque Limitation mode (if equipped).

- Engine torque is gradually limited for protection when coolant temperature

is too high. Check multifunction gauge display for engine temperature.

- Let engine cool down.

Engine is in limp home mode.

- Multifunction gauge CHECK ENGINE indicator lamp is on and display

shows LIMP HOME, seek service from an authorized Can-Am dealer, re-

pair shop, or person of your own choosing for maintenance, repair, or re-

placement. Please refer to the US EPA Emission-Related Warranty

contained herein for information about warranty claims.

5. ENGINE OVERHEATS

Low coolant level in cooling system.

- Check coolant level and refill. See Maintenance Procedures. Seek serv-

ice from an authorized Can-Am dealer, repair shop, or person of your own

choosing for maintenance, repair, or replacement. Please refer to the US

EPA Emission-Related Warranty contained herein for information about

warranty claims.

225

TROUBLESHOOTING GUIDELINES

Cooling fan is not working.

- Ensure cooling fans (at front and rear radiators) are not jammed and work-

ing properly.

- Check fan fuse. See Fuses in the Maintenance Procedures.

Dirty radiators fins.

- Check and clean radiator fins. See Maintenance Procedures.

6. ENGINE MISFIRE

Fouled/damaged/worn spark plug.

- Replace spark plugs as required.

Water in fuel.

- Drain fuel system and refill with fresh fuel.

7. PARTIAL OR NO RESPONSE FROM THE ACCELERA-

TOR PEDAL INPUTS (CHECK ENGINE IS ON AND PPS

FAULT MESSAGE IS DISPLAYED)

Partial failure of the accelerator pedal sensors (PPS).

- Use the override switch to retrieve accelerator pedal operation. Contact

an authorized Can-Am dealer.

Total failure of the accelerator pedal sensors (PPS).

- Use the override switch to bypass the accelerator pedal and increase the

engine speed in order to move vehicle. Contact an authorized Can-Am

dealer.

8. SHOCK ICON IS BLINKING FAST WHILE VEHICLE MAL-

FUNCTION TELLTALE IS ON

Partial failure of Smart-Shox system: Front or rear shock absorbers become

full stiff (Sport+ like).

- Change Smart-Shox mode to Sport+ to have a similar setting at front and

rear. The vehicle remains rideable. Contact an authorized Can-Am dealer.

Total failure of Smart-Shox system: Front and rear shock absorbers become

full stiff (Sport+ like).

- The vehicle remains rideable. Contact an authorized Can-Am dealer.

226

DIGITAL DISPLAY MESSAGES

If an abnormal engine condition occurs, the following messages can be com-

bined with a pilot lamp.

Message

Description

D.E.S.S. KEY

NOT

D.E.S.S. key requires cleaning.

RECOGNIZED

Indicates that you have used the wrong D.E.S.S. key, use

BAD KEY

the proper key for this vehicle.

All active or previously activated faults that require

CHECK ENGINE

attention.

No engine limitation engaged.

Critical faults requiring diagnostic as soon as possible.

LIMP HOME

An engine limitation is engaged and/or the engine behavior

is modified.

Throttle body fault, generally followed by a Limp Home

TPS FAULT

message.

BRAKE SWITCH

Brake signal fault.

FAULT

Check engine pilot light on (

CHECK DPS

Indicates that the DPS (Dynamic Power Steering) does not

work properly. See an authorized Can-Am dealer.

Faulty Pedal Position Sensor(s) (PPS). Refer to Override

PPS FAULT

Switch in Secondary Controls to drive the vehicle in the

limp home mode.

MANUAL LIMP

Confirms the Manual Limp Home is engaged using the

HOME

Override Switch in case of a PPS fault.

When the fuel sender resistor value is out of range the

FUEL SENSOR

multifunction gauge (analog/digital) will detect it and display

FAULT

the message.

The warning exclamation point light on (

CHECK

Indicates that the Smart-Lok does not work properly. See

SMART-LOK

an authorized Can-Am dealer.

227

BRP LIMITED WARRANTY FOR CANADA AND USA:

2024 CAN-AM® SSV

1) Scope of the Limited Warranty

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Can-Am SSV

(“Product (s)”) sold by authorized BRP Dealers (as hereinafter defined) in the

United States of America ("USA") and in Canada from defects in material or

workmanship for the period and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) Limitations of Liability

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EX-

PRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMI-

TATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. TO THE EXTENT THAT THEY CANNOT BE

DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CON-

SEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER

THIS WARRANTY. SOME STATES/PROVINCES DO NOT ALLOW FOR

THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED

ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WAR-

RANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE

OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE,

OR PROVINCE TO PROVINCE.

Neither the distributor, any BRP dealer nor any other person has been authorized

to make any affirmation, representation or warranty regarding the product, other

than those contained in this limited warranty, and if made, shall not be enforce-

able against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS – Are Not Warranted

The following are not warranted under any circumstances:

- Normal wear and tear;

- Routine maintenance items, tune ups, adjustments;

- Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

- Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

230

BRP LIMITED WARRANTY FOR CANADA AND USA: 2024 CAN-AM^® SSV

resulting from repairs done by a person that is not an authorized servicing

BRP dealer;

- Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

- Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

- Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

- Damages from rust, corrosion or exposure to the elements;

- Damage resulting from water or snow ingestion;

- Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work.

4) Warranty Coverage Period

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. SIX (6) consecutive months, for private use or commercial use owners

2. For emiission-related components, please also refer to the US EPA Emis-

sion-Related Warranty.

3. For evaporative emission-rellated components of Callifornia models

equipped wiith evaporatiive emission control system produced by BRP

for sale in the State of California that are originally sold to a resident or

subsequently warranty registered to a resident in the State of California, also

refer to the California Evaporative Emissions Control Warranty Statement.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this limited warranty beyond its original expiration

date.

5) Conditions to Have Warranty Coverage

This warranty coverage is available only if each of the following conditions has

been fulfilled:

1. The Product must be purchased as new and unused by its first owner from a

Dealer authorized to sell the Products in the country in which the sale oc-

curred (“Dealer”);

2. The BRP specified pre-delivery inspection process must be completed, docu-

mented and signed by the purchaser;

3. The Product must have undergone proper registration by an authorized

Dealer;

4. The Product must be purchased in the country in which the purchaser

resides;

5. Routine maintenance outlined in the Operator’s Guide must be timely per-

formed in order to maintain warranty coverage. BRP reserves the right to

make warranty coverage contingent upon proof of proper maintenance.

231

BRP LIMITED WARRANTY FOR CANADA AND USA: 2024 CAN-AM^® SSV

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

6) What to Do to Obtain Warranty Coverage

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP dealer within three (3) days of the appearance of the

anomaly and provide the Dealer with reasonable access to the Product and rea-

sonable opportunity to repair it.

The customer must also present to the Dealer, proof of purchase of the Product

and must sign the repair/work order prior to starting the repair in order to validate

the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

7) What BRP Will Do

BRP’s obligations under this warranty are limited to, at its sole discretion, repair-

ing or replacing parts found defective under normal use, maintenance and serv-

ice without charge for parts and labor, at any authorized BRP dealer during the

warranty coverage period under the conditions described herein. No claim of

breach of warranty shall be cause for cancellation or rescission of the sale of the

Product to the owner.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

8) Transfer

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

9) Consumer Assistance

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized dealer's service manager or

owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

232

US EPA EMISSION - RELATED WARRANTY

Bombardier Recreational Products Inc. (“BRP”) warrants to the ultimate purchas-

er and each subsequent purchaser that this new vehicle, including all parts of its

exhaust emission control system and its evaporative emission control system,

meets two conditions:

1. It is designed, built, and equipped so it conforms at the time of sale to the ulti-

mate purchaser with the requirements of 40 CFR 1051 and 40 CFR 1060.

2. It is free from defects in materials and workmanship that may keep it from

meeting the requirements of 40 CFR 1051 and 40 CFR 1060.

Where a warrantable condition exists, BRP will repair or replace, as it elects, any

part or component with a defect in materials or workmanship that would increase

the engine’s emissions of any regulated pollutant within the stated warranty peri-

od at no cost to the owner, including expenses related to diagnosing and repair-

ing or replacing emission-related parts. All defective parts replaced under this

warranty become the property of BRP.

For all emission-related warranty claims, BRP is limiting the diagnosis and repair

of emission-related parts to the authorized Can-Am dealers, unless for emer-

gency repairs as required by item 2 of the following list.

As a certifying manufacturer, BRP will not deny emission-related warranty claims

based on any of the following:

1. Maintenance or other service BRP or BRP's authorized facilities performed.

2. Engine/equipment repair work that an operator performed to correct an un-

safe, emergency condition attributable to BRP as long as the operator tries to

restore the engine/equipment to its proper configuration as soon as possible.

3. Any action or inaction by the operator unrelated to the warranty claim.

4. Maintenance that was performed more frequently than BRP specify.

5. Anything that is BRP fault or responsibility.

6. The use of any fuel that is commonly available where the equipment operates

unless BRP written maintenance instructions state that this fuel would harm

the equipment’s emission control system and operators can readily find the

proper fuel. See maintenance information section and fuel requirements of fu-

eling section.

Emission-Related Warranty Period

The emission-related warranty is valid for the following period whichever comes

first.

HOURS

MONTHS

KILOMETERS

Exhaust emission-related

500

5000

components

Evaporative emission-related

N/A

components

Components Covered

The emission-related warranty covers all components whose failure would in-

crease an engine’s emissions of any regulated pollutant, including the following

listed components:

233

US EPA EMISSION - RELATED WARRANTY

For exhaust emissions, emission-related components include any engine

parts related to the following systems:

- Air-induction system

- Fuel system

- Ignition system

- Exhaust gas recirculation systems.

The following parts are also considered emission-related components for ex-

haust emissions:

- After treatment devices

- Crankcase ventilation valves

- Sensors

- Electronic control units.

The following parts are considered emission-related components for evapora-

tive emissions:

- Fuel tank

- Fuel cap

- Fuel line

- Fuel line fittings

- Clamps*

- Pressure relief valves*

- Control valves*

- Control solenoids*

- Electronic controls*

- Vacuum control diaphragms*

- Control cables*

- Control linkages*

- Purge valves

- Vapor hoses

- Liquid/vapor separator

- Carbon canister

- Canister mounting brackets

- Carburetor purge port connector.

NOTE: *As related to the evaporative emission control system.

4. Emission-related components also include any other part whose only purpose

is to reduce emissions or whose failure will increase emissions without signifi-

cantly degrading engine/equipment performance.

Limited Applicability

As a certifying manufacturer, BRP may deny emission-related warranty claims

for failures that have been caused by the owner’s or operator’s improper mainte-

nance or use, by accidents for which the manufacturer has no responsibility, or

by acts of God. For example, an emission-related warranty claim need not be

honored for failures that have been directly caused by the operator’s abuse of

the engine/equipment or the operator’s use of the engine/equipment in a manner

for which it was not designed and are not attributable to the manufacturer in

anyway.

234

CALIFORNIA EVAPORATIVE EMISSIONS

CONTROL WARRANTY STATEMENT

The warranty periods begin on the date the new Off-Highway Recreational Ve-

hicle (“OHRV”) is delivered to an ultimate purchaser.

Bombardier Recreational Products Inc. (“BRP”) warrants to the ultimate purchas-

er and each subsequent purchaser that the OHRV is:

1. Designed, built, and equipped so as to conform, at the time of sale, with all

applicable laws, rules and regulations; and

2. Free from defects in materials and workmanship that may cause the failure of

a warranted part. All replacement parts must be identical in all material re-

spects to that part as described in BRP’s Executive Order of Certification

application.

The warranty on emissions-related parts function as follows:

Repair or replacement of any warranted part must be performed at no charge

to the OHRV owner, at a warranty station, except in the case of a temporary

repair when a warranted part or a warranty station is not reasonably available

to the OHRV owner. In the event a temporary repair is permitted, repairs may

be performed at any available service establishment, or by the owner, using

any replacement part. BRP must reimburse the owner for his or her expenses

including diagnostic charges for such temporary repair or replacement, not to

exceed BRP's suggested retail price for all warranted parts replaced and la-

bor charges based on BRP's recommended time allowance for the warranty

repair and the geographically appropriate hourly labor rate.

The lack of availability of warranted parts or the incompleteness of repairs

within a reasonable time period, not to exceed 30 days from the time the

OHRV is initially presented to the warranty station for repair, will qualify the

need for a temporary repair.

Any warranted part which is not scheduled for replacement as part of mainte-

nance in the written instructions must be warranted for the warranty period

defined below. If any such part fails during the warranty period, it must be re-

paired or replaced by BRP. Any such part repaired or replaced under war-

ranty must be fully warranted.

Any warranted part which is scheduled only for regular inspection in the writ-

ten instructions must be warranted for the warranty period defined below. A

statement in such written instructions to the effect of “repair or replace as nec-

essary” does not reduce the period of warranty coverage. Any such part re-

paired or replaced under warranty is warranted for the remaining warranty

period.

Any warranted part which is scheduled for replacement as part of mainte-

nance in the written instructions is warranted for the period of time prior to the

first scheduled replacement point for that part. If the part fails before the first

scheduled replacement point, the part will be repaired or replaced by BRP.

Any such part repaired or replaced under warranty is warranted for the re-

mainder of the period prior to the first scheduled replacement point for the

part.

Warranty services or repairs are provided at all manufacturer dealerships that

are owned by the manufacturer or franchised to service the subject OHRVs.

The OHRV owner will not be charged for diagnostic labor which leads to the

determination that a warranted part is, in fact, defective, provided that such di-

agnostic work is performed at a warranty station.

236

CALIFORNIA EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT

8. BRP is liable for damages to other vehicle components proximately caused

by a failure, under warranty, of any warranted part.

9. Any replacement part designated by BRP may be used in warranty repairs

provided without charge to the OHRV owner. Such use will not reduce the

warranty obligations of BRP, except that BRP will not be liable for repair or re-

placement of any replacement part which is not a warranted part.

10. Any add-on or modified part exempted by the Air Resources Board from the

prohibitions of section 27156 of the California Vehicle Code may be used on

an OHRV. Such use, in and of itself, will not be grounds for disallowing a war-

ranty claim. BRP is not liable to warrant failures of warranted parts caused by

the use of an add-on or modified part (s) unless such part (s) are also

warranted.

Conditions and exclusions:

- BRP may deny you warranty coverage if your OHRV or a part has failed di-

rectly due to abuse, neglect, improper maintenance or unapproved

modifications.

Your Warranty Rights And Obligations

The California Air Resources Board is pleased to explain the evaporative emis-

sions control system warranty on your 2024 Off-Road Sport Vehicle. In Califor-

nia, new off-highway recreational vehicles must be designed, built, and equipped

to meet the State’s stringent anti-smog standards. BRP must warrant the evapo-

rative emissions control system on your Off-Road Sport Vehicle for the periods of

time listed below provided there has been no abuse, neglect, improper mainte-

nance, or unapproved modification of your Off-Road Sport Vehicle.

Your evaporative emissions control system may include parts such as the carbu-

retor or fuel-injection system, fuel tank, fuel hoses, carbon canister, and engine

computer. Also included may be hoses, belts, connectors and other evaporative

emissions-related assemblies. Where a warrantable condition exists, Bombardier

Recreational Products Inc. will repair your Off-Road Sport Vehicle at no cost to

you including diagnosis, parts and labor.

OHRV Manufacturer’s Warranty Coverage

The warranty period for this OHRV is 60 months, or 5000 miles, or 500 hours,

whichever comes first.

Parts covered:

1. Canister Mounting Bracket(s)

2. Carbon Canister

3. Purge Port Connector

4. Clamp(s)*

5. Electronic Control*

6. Fuel Cap

7. Filler Neck

8. Filler Neck Hose

9. Fuel Line(s)

10. Fuel Line Fitting(s)

11. Fuel Tank

12. Pressure Relief Valve(s)*

237

CALIFORNIA EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT

13. Purge Valve(s)

14. Check Valve(s)*

15. Vapor Hose(s)

16. Flow Reducer

17. Filter(s)*

18. Fuel pump

19. All other parts not listed that may affect the evaporative emissions control

system

NOTE: *As related to the evaporative emission control system.

If any evaporative emissions-related part on your Off-Road Sport Vehicle is de-

fective the part will be repaired or replaced by Bombardier Recreational Products

Inc.

Owner’s Warranty Responsibilities

As the Off-Road Sport Vehicle owner you are responsible for the performance of

the required maintenance listed in your owner’s manual. Bombardier Recreation-

al Products Inc. recommends that you retain all receipts covering maintenance

on your Off-Road Sport Vehicle, but Bombardier Recreational Products Inc. can-

not deny warranty solely for the lack of receipts or for failure to ensure the per-

formance of a scheduled maintenance.

As an owner you are responsible for presenting your Off-Road Sport Vehicle to a

Bombardier Recreational Products Inc. dealer as soon as a problem exists. The

warranty repairs should be completed in a reasonable time, not to exceed 30

days.

As an Off-Road Sport Vehicle owner, you should also be aware that Bombardier

Recreational Products Inc. may deny you warranty coverage if your Off-Road

Sport Vehicle or a part has failed due to abuse, neglect, improper maintenance

or unapproved modifications.

If you have any questions regarding your warranty rights and responsibilities, you

should contact:

- Bombardier Recreational Products Inc. at 1-888-272-9222, or

- The California Air Resources Board at 4001 Iowa Avenue, Riverside, CA

92507.

238

BRP LIMITED WARRANTY FOR INTERNATIONAL:

2024 CAN-AM® SSV

1) Scope of the Limited Warranty

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Can-Am SSV

(“Product(s)”) sold by distributors or dealers authorized by BRP to distribute the

Products outside of the United States of America ("USA"), Canada, member

states of the European Economic Area (which is comprised of the states of the

European Union plus the United Kingdom, Norway, Iceland and Liechtenstein)

("EEA"), Turkey, member states of the Commonwealth of the Independent States

(including Ukraine and Turkmenistan) ("CIS") from defects in material or work-

manship for the period and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any

point, even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) Limitation of Liability

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EX-

PRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMI-

TATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. TO THE EXTENT THAT THEY CANNOT BE

DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CON-

SEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER

THIS WARRANTY. SOME STATES/PROVINCES DO NOT ALLOW FOR

THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED

ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WAR-

RANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE

OTHER LEGAL RIGHTS WHICH MAY VARY FROM COUNTRY TO COUN-

TRY. BRP SHALL NOT BE HELD LIABLE IF PRODUCTS OR WARRANTY

PARTS ARE NOT AVAILABLE IN CERTAIN COUNTRIES FOR REASONS

OUTSIDE OF BRP’S CONTROL.

For Products purchased in Australia, refer to the Australia-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

239

BRP LIMITED WARRANTY FOR INTERNATIONAL: 2024 CAN-AM^® SSV

3) EXCLUSIONS – Are Not Warranted

The following are not warranted under any circumstances:

- Normal wear and tear;

- Routine maintenance items, tune ups, adjustments;

- Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

- Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

- Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

- Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

- Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

- Damages from rust, corrosion or exposure to the elements;

- Damage resulting from water or snow ingestion;

- Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work.

The following list includes, without limitation, items that are considered wear

items and that are not covered under BRP's limited warranty unless failure is a di-

rect result of a defect in material or workmanship:

- Batteries

- Brake pads

- Brake disks and drums

- Clutch plates / pads

- Clutch sliders

- Clutch springs

- Clutch replaceable bushings

- Drive belts

- Filters

- Finished and unfinished surfaces

- Fuses

- Light bulbs / sealed

- Lubricants

- Spark plugs

- Suspension bushings

- Suspension slider shoes

- Suspension springs

- Tires

4) Warranty Coverage Period

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

240

BRP LIMITED WARRANTY FOR INTERNATIONAL: 2024 CAN-AM^® SSV

1. SIX (6) consecutive months, for private use or commercial use owners

In AUSTRALIA and NEW ZEALAND only, this warranty will be in effect from (1)

the date of delivery to the first retail consumer or (2) the date the product is first

put into use, whichever occurs first, and for a period of TWELVE (12) CONSEC-

UTIVE MONTHS and THIRTY SIX (36) CONSECUTIVE MONTHS for Power-

train Engine and Transmission systems only, for private use or commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty pe-

riod which can be extended by any applicable warranty promotional program, as

the case may be.

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

5) For Products Sold In Australia Only

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensa-

tion for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

Nothing in these Warranty terms and conditions should be taken to exclude, re-

strict or modify the application of any condition, warranty, guarantee, right or rem-

edy conferred or implied under the Competition and Consumer Act 2010 (Cth),

including the Australian Consumer Law or any other law, where to do so would

contravene that law, or cause any part of these terms and conditions to be void.

The benefits given to you under this limited warranty are in addition to other rights

and remedies that you have under Australian law.

6) Conditions to Have Warranty Coverage

This warranty coverage is available only if each of the following conditions has

been fulfilled:

1. The Product must be purchased as new and unused by its first owner from a

Distributor/Dealer authorized to distribute Products in the country in which the

sale occurred (“Distributor/Dealer”);

2. The BRP specified pre-delivery inspection process must be completed, docu-

mented and signed by the purchaser;

3. The Product must have undergone proper registration by an authorized Dis-

tributor/Dealer;

4. The Product must be purchased in the country in which the purchaser

resides;

5. Routine maintenance outlined in the Operator’s Guide must be timely per-

formed in order to maintain warranty coverage. BRP reserves the right to

make warranty coverage contingent upon proof of proper maintenance.

241

BRP LIMITED WARRANTY FOR INTERNATIONAL: 2024 CAN-AM^® SSV

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

7) What to Do to Obtain Warranty Coverage

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

8) What BRP Will Do

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

9) Transfer

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

10) Consumer Assistance

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

242

BRP LIMITED WARRANTY FOR THE EUROPEAN

ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024

CAN-AM® SSV

1) Scope of the Limited Warranty

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Can-Am SSV

(“Product(s)”) sold by distributors or dealers authorized by BRP to distribute the

Products in member states of the European Economic Area (which is comprised

of the states of the European Union plus the United Kingdom, Norway, Iceland

and Liechtenstein) ("EEA"), Turkey, member states of the Commonwealth of the

Independent States (including Ukraine and Turkmenistan) ("CIS") (“Distributor/

Dealer”) from defects in material or workmanship for the period and under the

conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) Limitations of Liability

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EX-

PRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMI-

TATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. TO THE EXTENT THAT THEY CANNOT BE

DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CON-

SEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER

THIS WARRANTY. SOME STATES/PROVINCES DO NOT ALLOW FOR

THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED

ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WAR-

RANTY GIVES YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE

OTHER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE,

OR PROVINCE TO PROVINCE. BRP SHALL NOT BE HELD LIABLE IF

PRODUCTS OR WARRANTY PARTS ARE NOT AVAILABLE IN CERTAIN

COUNTRIES FOR REASONS OUTSIDE OF BRP’S CONTROL.

For Products purchased in France, refer to the France-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

244

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 CAN-AM^® SSV

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS – Are Not Warranted

The following are not warranted under any circumstances:

- Normal wear and tear;

- Routine maintenance items, tune ups, adjustments;

- Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

- Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

- Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

- Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

- Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

- Damages from rust, corrosion or exposure to the elements;

- Damage resulting from water or snow ingestion;

- Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work.

The following list includes, without limitation, items that are considered wear

items and that are not covered under BRP's limited warranty unless failure is a di-

rect result of a defect in material or workmanship:

- Batteries

- Brake pads

- Brake disks and drums

- Clutch plates / pads

- Clutch sliders

- Clutch springs

- Clutch replaceable bushings

- Drive belts

- Filters

- Finished and unfinished surfaces

- Fuses

- Light bulbs / sealed

- Lubricants

- Spark plugs

- Suspension bushings

- Suspension slider shoes

- Suspension springs

- Tires

245

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 CAN-AM^® SSV

4) Warranty Coverage Period

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWENTY-FOUR (24) consecutive months, for private use owners.

2. SIX (6) consecutive months, for commercial use owners.

A Product is used commercially when it is used in connection with any work or

employment that generates income during any part of the warranty period. A

Product is also used commercially when, at any point during the warranty period,

it is licensed for commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty pe-

riod which can be extended by any applicable warranty promotional program, as

the case may be.

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

5) For Products Sold In France Only

The seller shall deliver goods that are complying with the contract and shall be

responsible for defects existing upon delivery. The seller shall also be responsi-

ble for defects resulting from packaging, assembling instructions or the installa-

tion when it is its responsibility per the contract or if accomplished under its

responsibility. To be compliant with the contract, the good shall:

1. Be fit for normal use for goods similar thereto and, if applicable:

- Correspond to the description provided by the seller and have the qualities

presented to the buyer though sample or model;

- Have the qualities that a buyer may legitimately expect considering the

public declarations of the seller, the manufacturer of its representative, in-

cluding in advertising or labeling; or

2. Have the characteristics mutually agreed upon as between the parties or be

fit for the specific use intended by the buyer and brought to the attention of

the seller and which accepted.

The action for failure to comply is prescribed after two years after delivery of the

goods. The seller is responsible for the warranty for hidden defects of the good

sold if such hidden defects are rendering the good unfit for the intended use, or if

they diminish its use in such a way that the buyer would not have acquired the

good or would have given a lesser price, had he known. The action for such hid-

den defects shall be taken by the buyer within 2 years of the discovery of the

defect.

6) Conditions to Have Warranty Coverage

This warranty coverage is available onlly if each of the following conditions has

been fulfilled:

246

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 CAN-AM^® SSV

1. The Product must be purchased as new and unused by its first owner from a

Distributor/Dealer authorized to distribute Products in the country (or in the

case of the EEA, union of countries) in which the sale occurred (“Distributor/

Dealer”);

2. The BRP specified pre-delivery inspection process must be completed, docu-

mented and signed by the purchaser;

3. The Product must have undergone proper registration by an authorized Dis-

tributor/Dealer;

4. The Product must be purchased in the country (or in the case of the EEA,

union of countries) in which the purchaser resides;

5. Routine maintenance outlined in the Operator’s Guide must be timely per-

formed in order to maintain warranty coverage. BRP reserves the right to

make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

7) What to Do to Obtain Warranty Coverage

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

8) What BRP Will Do

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, or for

EEA residents, if service is required outside of the EEA, the owner will bear re-

sponsibility for any additional charges due to local practices and conditions, such

as, but not limited to, freight, insurance, taxes, license fees, import duties, and

any and all other financial charges, including those levied by governments,

states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

247

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 CAN-AM^® SSV

9) Transfer

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

10) Consumer Assistance

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

248

DATA PRIVACY INFORMATION

Bombardier Recreational Products inc., its affiliates and subsidiaries (“BRP”) is

committed to protecting your privacy and support a general policy of openness

about how we collect, use and disclose your personal information in the course

of managing our relationship with you. More detaiils can be found by visiting

BRP’’s Priivacy Poliicy at:

https://brp.com/en/privacy-poliicy.htmll or by scanniing the QR Code below.

Please be assured that we have appropriate security measures in place to en-

sure that your personal information is protected against loss and unauthorized

access.

Your personal information that may be collected by BRP, directly from you or

from authorized dealers or authorized third parties, includes:

- Contact, Demographiic & Registratiion Informatiion (e.g., name, full ad-

dress, phone number, email, gender, ownership history, language of

communication)

- Vehicle Information (e.g., serial number, purchase and delivery date, unit

usage, vehicle location and movements)

- Third Party Informatiion (e.g., information received from BRP partners, join-

t-marketing activities information, social media)

- Technological Information (e.g., IP address, type of device, operating sys-

tem, browser type, webpages you view, cookies and similar technologies

when you use BRP or dealers’ websites or mobile application)

- Interaction with BRP Information (e.g., information collected when you call

BRP’s in-house sales representatives, buy items on a BRP web Site, sign up

for BRP emails, participate in BRP-sponsored contests and sweepstakes or

attend BRP-sponsored events)

- Transactiionall Informatiion (e.g., information necessary to handle returns,

payment information when you purchase our products or services through

our websites or mobile applications and other issues related to your purchase

of BRP products)

This information may be used and processed for the following purposes:

- Safety & Security

- Customer Support for Sales & After Sales (e.g., complete or follow up with

you about your purchase or maintenance)

- Registration & Warranty

- Communication (e.g., sending you a BRP satisfaction survey)

- Online Behavioural Advertising, Profiling and Location-Based Services

(e.g., offer customized experience)

- Compliance & Dispute Resolution

- Marketing & Advertising

- Assistance (e.g., help with any delivery issues, handle returns, and other is-

sues related to your purchase of BRP products).

We also may use personal information to generate aggregated or statistical data

that no longer identifies you personally.

Your personal informatiion may be disclosed to the folllowiing: BRP, BRP’s

authoriized deallerships, diistriibutors, serviice proviiders, advertising & mar-

ket research partners and other authoriized third partiies.

We may receive information about you from diverse sources, including third par-

ties, such as BRP’s authorized dealerships and partners, with whom we offer

250

DATA PRIVACY INFORMATION

services or engage in joint-marketing activities. We may also receive information

about you from social media platforms such as Facebook and Twitter, when you

interact with us on those platforms.

Depending on the circumstances, your personal information may be communi-

cated outside the region where you reside. Your personal information is retained

only for as long as necessary for the purpose for which we obtained it and ac-

cording to our retention policies.

To exercise your data privacy rights (e.g. right of access, right of rectification), to

withdraw your consent in order to be removed from the address list for marketing

purposes or for the satisfaction survey or for general data privacy questions,

please contact BRP’s Data Protection Officer at or by mail at privacyoffii-

cer@brp.com or by mail at:

BRP Legal Service, 726 St-Joseph, Valcourt, Quebec, Canada, J0E 2L0.

When BRP processes your personall iinformation, they do so in complliance

wiith its Privacy Pollicy avaiilable at: https://www.brp.com/en/privacy-poliicy.

htmll or by using the folllowiing

QR Code.

251

www.brp.com

Asia Pacific

Australia

Level 26

477 Pitt Street

Sydney, NSW 2020

China

上海市徐汇区衡山路10号6号楼301

Rm 301, Building 6,

No.10 Heng Shan Rd,

Shanghai, China

Japan

21F Shinagawa East One Tower

2-16-1 Konan, Minato-ku-ku,

Tokyo 108-0075

New Zealland

Suite 1.6, 2-8 Osborne Street,

Newmarket, Auckland 2013

Europe, Middle East and Africa

Bellgium

Oktrooiplein 1

9000 Gent

Czech Republiic

Stefanikova 43a

Prague 5

150 00

Germany

Itterpark 11

40724 Hilden

Fiinland

Isoaavantie 7

PL 8040

96101 Rovaniemi

France

Arteparc Bâtiment B

Route de la côte d'Azur,

13 590 Meyreuil

Norway

Ingvald Ystgaardsvei 15

N-7484 Trondheim

252

CHANGE OF ADDRESS AND OWNERSHIP

If your address has changed or if you are the new owner of the vehicle, be sure

to notify BRP by either:

- Notifying an authorized Can-Am dealer.

- North America Only: calling at 1 888 272-9222.

- Mailing one of the change of address cards on the following pages at one of

the BRP addresses indicated in the Contact Us section of this guide.

In case of change of ownership, please join a proof that the former owner agreed

to the transfer.

Notifying BRP, even after the expiration of the limited warranty, is very important

as it enables BRP to reach the vehicle owner if necessary, like when safety re-

calls are initiated. It is the owner’s responsibility to notify BRP.

STOLEN UNITS: If your personal vehicle is stolen, you should notify BRP or an

authorized Can-Am dealer. We will ask you to provide your name, address,

phone number, the vehicle identification number and the date it was stolen.

254

Can-Am MAVERICK R — X AND X RS SERIES. OPERATOR’S GUIDE (2024) - page 2