BRP Sea-Doo SPARK SERIES. OPERATOR’S GUIDE (2024)

SPECIAL PROCEDURES

5. While still holding the iBR lever in,

Capsized Watercraft

press the VTS UP/DOWN button

to move the iBR gate to the de-

NOTICE

sired position. Ensure the VTS in-

When the watercraft has been

dication in the multifunction gauge

turned over 5 minutes, do not at-

changes with the iBR gate move-

tempt to crank the engiine to avoiid

ment. If the iBR gate moves up-

water iingestion that woulld dam-

wards, the indication moves

age the engine. See an author-

upwards.

ized Sea-Doo dealer as soon as

6. Release the iBR lever.

possiible.

7. Remove the tether cord from the

engine cut-off switch.

NOTICE

WARNING

If the engine does not crank, do

If it is necessary to reach in to re-

not attempt to start iit anymore.

move any foreiign object caught iin

Otherwiise, the engine coulld be

the propulsion system, strictly ob-

damaged. See an authorized

serve the folllowiing before

Sea-Doo dealler as soon as

proceeding:

possiible.

–

Remove tether cord from the

engine cut-off switch.

WARNING

–

Wait at least 5 miinutes.

–

Do not press on START/STOP

When watercraft is capsized, do

button. Should the START /

not attempt to restart the engine.

STOP button be pressed, waiit

Operator and passengers should

another

5 miinutes.

allways wear approved personall

fllotation deviices.

CAUTION

Heat exchanger in the hull may

become very hot. Avoid any con-

tact with the heat exchanger as

burns may occur.

NOTE:

It is recommended to ride the vehicle

for approximately 5 minutes with en-

gine speed lower than 5000 RPM to

evacuate any water that might have

been accumulated in the bilge. Never

exceed 5000 RPM. If not, water could

get inside the engine.

Submerged Watercraft

To limit damages to the engine, per-

form the following procedure as soon

as possible.

1. Drain bilge.

103

SPECIAL PROCEDURES

2. If it was submerged in salt water,

This will prevent the exhaust system

spray bilge and all components

from filling with water, which may lead

with fresh water using a garden

to water being injected into and filling

hose to stop the salt corroding

the engine. Without the engine run-

effect.

ning, there isn't any exhaust pressure

to push the water out the exhaust

NOTICE

outlet.

Never try to crank or start the en-

giine. Water trapped iin iintake

NOTICE

maniifolld would flow towards the

engine and possiibly cause severe

Faillure to folllow these instructions

engine damage.

may result iin damage to the en-

gine. If you must tow a stranded

watercraft in water, be sure not to

3. Bring the watercraft to an author-

exceed the maxiimum towiing

ized Sea-Doo dealer as soon as

speed of 8 km/h (5 MPH).

possible to have it serviced.

NOTICE

Faiilure to have the engine prop-

NOTICE

erlly serviced may cause severe

engine damage.

Never tow a watercraft faciing

backwards as water iintrusion may

occur.

Water-Flooded Engine

NOTICE

Never try to crank or start the en-

CAUTION

giine. Water trapped iin iintake

A tow lline shalll allways be made

maniifolld would flow towards the

fast in such a way that iit can be

engine and possiibly cause severe

released when under load.

engine damage.

Bring the watercraft to an authorized

Sea-Doo dealer as soon as possible

to have it serviced.

NOTICE

Faiilure to have the engine prop-

erlly serviced may cause severe

engine damage.

Towing the Watercraft in

Water

Special precautions should be taken

when towing a Sea-Doo watercraft in

water.

The maximum recommended towing

speed is 8 km/h (5 MPH).

104

MAINTENANCE SCHEDULE

Maintenance is very important to keep your watercraft in safe operating condi-

tion. The vehicle should be serviced as per the maintenance schedule.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

Perform periodic checks and follow the maintenance schedule. The maiinte-

nance schedule does not exempt the pre-ride inspection.

WARNING

Faiilure to properly maiintain the watercraft accordiing to the maiintenance

schedulle and procedures can make it unsafe to operate.

EPA Regulation - Canadian and USA Watercrafts

A repair shop or person of the owner''s choosing may maiintaiin, replace, or

repair emission control devices and systems. These instructions do not require

components or service by BRP or authorized Sea-Doo dealers.

Although an authorized Sea-Doo dealer has an in-depth technical knowledge

and tools to service your vehicle, the emission-related warranty is not conditioned

on the use of an authorized Sea-Doo dealer or any other establishment with

which BRP has a commercial relationship.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

For emission-related warranty claims, BRP is limiting the diagnosis and repair of

emission-related parts to the authorized Sea-Doo dealers. For more information,

please refer to the US EPA Emissions Warranty contained in the warranty

section.

You must follow the instructions for fuel requirements in the fueling section of this

manual. Even if gasoline containing greater than ten volume percent ethanol is

readily available, the US EPA issued a prohibition against the use of gasoline

containing greater than 10 vol% ethanol that applies to this vehicle. The use of

gasoline containing greater than 10 vol% ethanol with this engine may harm the

emission control system.

106

MAINTENANCE SCHEDULE

Maintenance Schedule

Make sure to perform proper maintenance at recommended intervals as indi-

cated in the tables.

The maintenance chart indicates the items needing to be addressed based on 2

criteria, whichever happens first:

- Calendar time

- Watercraft hours.

Your driving habits determines the factors you shall adhere to. For example:

- Someone who uses their watercraft every weekend would follow the hours

reading to determine the frequency of his maintenance.

- Someone who uses their watercraft seldomly over the year or only on a few

occasions would follow the calendar tiime to determine the frequency of his

maintenance.

IMPORTANT: The following tables show the appropriate maintenance appli-

cation for the first

years. For subsequent years, repeat the same pattern

alternatively.

Maintenance Overview

Regular/ Salt/ Dirty

Calendar Time

Hour meter

water

Every Month

A+

1 Year

100 Hours

Every Month

A+

2 Years

200 Hours

A and B

Every Month

A+

3 Years

300 Hours

900 ACE Engines

Regular

A=Adjust

C=Clean

F=Flush

Every year

Every 2 years

I=Inspect

L=Lubricate

100 Hours

200 Hours

R=Replace

T=Torque

Air and Fuel Delivery

Air delivery components and function (ducts,

I, C

hoses, clamps)

Fuel components and function (Fuel tank cap,

fuel tank fixation, hose condition, leaks)*

107

MAINTENANCE SCHEDULE

Regullar

A=Adjust

C=Clean

F=Flush

Every year

Every 2 years

I=Inspect

L=Lubricate

100 Hours

200

Hours

R=Replace

T=Torque

Flame arrestor

Deck and Hull

Sacrificial anode(s)

Body panels and hardware

I, T

Hull

Engine and Cooling

Engine cooling components (coolant

concentration, coolant level, hose condition,

I, A

clamps, leaks)

Engine oil and oil filter

Ignition components and function

Engine rubber mounts

Spark plugs

Engine coolant

Every 5 years

or 300 hour

Exhaust and Emissions

Exhaust components (gaskets, pipes, muffler

condition, leaks)*

Exhaust

iBR

iBR components and function*

Propulsion

Propulsion components and function*

Electrical

Battery connections and condition*

Electrical harness routing

Modules and applicable software updates

Operation of control switches and lighting

Steering and Controls

Steering components and function*

Throttle operation

108

MAINTENANCE SCHEDULE

SALT/ DIRTY

A+

WATER

After each

ride in salt

A=Adjust

C=Clean

dirty water

Every 2

F=Flush

Every year

years

I=Inspect

monthlly

L=Lubricate

100 Hours

when used in

200 Hours

R=Replace

salt

T=Torque

dirty water

Air and Fuel Delivery

Air delivery components and

I, C

function (ducts, hoses, clamps)

Fuel components and function (Fuel

tank cap, fuel tank fixation, hose

condition, leaks)*

Flame arrestor

Deck and Hull

Sacrificial anode(s)

Every month

Body panels and hardware

I, T

Hull

Engine and Cooling

Engine compartment

After each

ride

Engine compartment metallic

components

Each month

Engine cooling components (coolant

concentration, coolant level, hose

I, A

condition, clamps, leaks)

Engine oil and oil filter

Ignition components and function

Engine rubber mounts

Spark plugs

Engine coolant

Every 5 years

or 300 hour

Exhaust and Emissions

Exhaust components (gaskets,

pipes, muffler condition, leaks)*

110

MAINTENANCE SCHEDULE

SALT/ DIRTY

A+

WATER

After each

ride in salt

A=Adjust

C=Clean

dirty water

Every 2

F=Flush

Every year

years

I=Inspect

monthly

L=Lubricate

100 Hours

when used in

200 Hours

R=Replace

salt

T=Torque

dirty water

Exhaust

After each

ride

iBR

iBR components and function*

Propulsion

Propulsion components and

function*

Electrical

Battery connections and condition*

Electrical harness routing

Modules and applicable software

updates

Operation of control switches and

lighting

Steering and Controls

Steering components and function*

Throttle operation

*For an extensive list of maintenance actions to be performed, refer to the Main-

tenance Checklist.

111

MAINTENANCE PROCEDURES

This section includes instructions for

WARNING

basic maintenance procedures.

Should removall of a llocking de-

vice (e.g. lock tabs, self-lockiing

WARNING

fasteners, etc.) be required, all-

Turn off the engiine and folllow

ways repllace with a new one.

these maiintenance procedures

when performing maintenance. If

you do not folllow proper maiinte-

NOTICE

nance procedures you can be in-

Never leave any objject, rag, tool,

jured by hot parts, moving parts,

etc., in the engine compartment or

ellectriciity, chemiicalls or other

in the biilge.

hazards.

Engine Oil

Recommended Engiine Oiil

Rotax^® engines were developed and validated using the XPS^® oil.

BRP recommends the use of its XPS engine oil or an equivalent at all time.

Damage caused by the use of an oil not suitable for the engine may not be cov-

ered by the BRP Limited Warranty.

XPS Recommended Engine Oil

General purpose

5W40 synthetic blend oil

Warm temperature

10W50 synthetic oil

If the recommended XPS engine oil is not available:

112

MAINTENANCE PROCEDURES

Use a 4-stroke SAE synthetiic

engine oill meeting or exceeding the

following lubricant industry

specifications.

Always check the API service label

Engine Without Supercharger

certification on the oil container, it

must contain at least one of the

indicated standards.

API serviice classiificatiion SN or

JASO-MA2

Use a 4-stroke SAE motorcyclle

engine oill compatiblle wiith wet

cllutches meeting or exceeding the

following lubricant industry

specifications.

Engine Wiith Supercharger

Always check the API service label

certification on the oil container, it

must contain at least one of the

indicated standards.

API serviice classiificatiion SN or

JASO-MA2

Engine Oill Level

1. Raise trailer tow pole, then block in

position when bumper rail is level.

NOTICE

2. Install a garden hose on the ex-

Operating the engine with an im-

haust system flushing connector.

Refer to Exhaust System in this

proper llevell may severelly dam-

section and follow the procedure.

age engine.

NOTICE

CAUTION

Never run engine wiithout supply-

Many components in the engine

ing water to the exhaust system.

compartment may be very hot. Di-

Faiilure to cool exhaust system

rect contact may result in skin

may severely damage iit.Never run

burn.

engine longer than 2 minutes.

Driive lline seall has no cooliing

when watercraft iis out of water.

NOTICE

Watercraft must be llevel.

3. With the engine already at normal

operating condition, let engine idlle

CAUTION

for 30 seconds then stop engine.

4. Wait at least 30 seconds for the oil

When operatiing the engiine whille

to settle in the engine.

the watercraft iis out of water, the

5. To check level, remove access

heat exchanger iin the riide pllate

cover located on rear of RH side of

may become very hot. Avoid any

watercraft

turning

contact with the riide pllate as

counterclockwise.

burns may occur.

113

MAINTENANCE PROCEDURES

- Add the recommended oil to

the proper level.

NOTE:

Every time oil is added in the engine,

the complete procedure explained in

this section must be carried out again.

Otherwise, you will obtain a false oil

level reading.

10. Properly reinstall dipstick and RH

access cover.

NOTICE

TYPICAL

Ensure that oiil filler cap is tighten

1. RH access cover

properlly. Otherwise engiine oiil can

spiilll out.

6. Unscrew dipstick, pull it out and

wipe clean.

Engine Oil Change and Oill Fillter

7. Reinstall

dipstick,

push in

Replacement

completely.

8. Remove dipstick again and read

The oil change and filter replacement

oil level. It should be between the

may be performed by an authorized

MAX and MIN marks.

Sea-Doo dealer, repair shop, or per-

son of your own choosing.

Engine Coolant

Recommended Engine Coollant

1. Maximum

XPS Recommended Coolant

2. Minimum

3. Operating range

Extended life pre-mixed coolant

If the Recommended XPS Coolant

9. Add oil to ensure the level is be-

is Not Available

tween marks as required.

Use a low silicate, extended life

NOTICE

ethylene-glycol premixed coolant

Do not overfiilll.

(50%-50%) specifically formulated

for internal combustion aluminum

engines.

To add oil:

- Place a funnel in the oil neck

opening.

NOTICE

Allways use ethylene-glycoll antii-

freeze containing corrosion iinhiibi-

tors speciifiicallly for internal

combustiion alluminum engines.

To prevent antifreeze deterioration, al-

ways use the same brand and grade.

114

MAINTENANCE PROCEDURES

Never mix different brands or grades

unless cooling system is completely

flushed and refilled.

Engine Coollant Levell

WARNING

Check coolant level with engiine

cold. Never add coollant when en-

gine is hot.

CAUTION

1. Expansion tank cap

Many components in the engine

compartment may be very hot. Di-

With watercraft on a level surface, add

rect contact may result in skin

coolant until it is visible without ex-

burn.

ceeding the COLD level mark in cool-

ant reservoir when engine is cold.

To access the expansion tank, turn

the LH access cover knob 1/4 turn

counter-clockwise to unlock, then pull

out to unsnap the rear portion and

slide rearward to remove.

1. Cold level mark

LH ACCESS COVER

1. To unlock, turn the knob

1/4

turn

NOTE:

counter-clockwise

The watercraft is level when it is in

water. When on a trailer, raise trailer

Locate the expansion tank cap.

tow pole and block in this position

when the lower part of the hull is level.

Add coolant, see Recommended En-

gine Coolant for specification, to ad-

just coolant level between marks as

required. Use a funnel to avoid spill-

age. Do not overfill.

Properly reinstall and tighten expan-

sion tank cap, then reinstall the LH ac-

cess cover in the reverse of removal

115

MAINTENANCE PROCEDURES

procedure and lock the knob by turn-

2. Unclip the steering cable by push-

ing it 1/4 turn clockwise.

ing the ring up towards the nut.

LH ACCESS COVER

1. To lock, turn the knob 1/4 turn clockwise

STEERING CABLE UNCLIPPED

1. Ring

NOTE:

2. Nut

A cooling system that frequently re-

quires coolant is an indication of leaks

3. Put the jet pump nozzle in straight

or engine problems. See an author-

position.

ized Sea-Doo dealer.

4. Unscrew nut to turn handlebar to

the right.

Engiine Coolant Replacement

5. Screw nut to turn handlebar to the

left.

Coolant replacement should be per-

6. When steering alignment is com-

formed by an authorized Sea-Doo

plete, clip the steering cable by

dealer.

pushing the ring back down and

reinstalling the LH side knee pad.

Steering Alignment

1. Manually release and remove the

Central Body

LH side knee pad.

Removing the Central Body

NOTE:

When necessary, remove the central

This area is intended only to access

body as follows:

the steering cable assembly. Do not

use this area for storage purposes.

WARNING

Never attempt to llift the central

body alone. Liift only with assis-

tance or use an appropriate lifting

deviice. Lifting alone can cause

seriious iinjjury.

1. Turn the LH access cover knob 1/4

turn counter-clockwise to unlock,

then pull out to unsnap the rear

portion and slide rearward to

remove.

1. LH Side knee pad

116

MAINTENANCE PROCEDURES

9. Remove both front body panels.

12. Remove the ten M6

nuts and

screws from both sides of central

body.

10. Remove the self-tapping screws at

front of central body as shown.

13. Carefully lift the central body off

the hull using an appropriate lifting

strap.

NOTE:

When lifting central body, wrap strap

around the handlebars. Wrapping

elsewhere on central body to lift it may

cause damages.

Installliing the Central Body

1. Use an appropriate lifting strap to

11. Remove

the six self-tapping

safely lower the central body in

screws at

the

rear of the central

position.

body.

WARNING

Never attempt to llift the central

body alone. Liift only with assis-

tance or use an appropriate lifting

deviice. Lifting alone can cause

seriious iinjjury.

2. Properly locate the central body

with the alignment tabs on the hull.

118

MAINTENANCE PROCEDURES

CENTRAL BODY

- STARBOARD SIDE

VIEW

1. Grooved alignment tab on central body

2. Rib in hull

6. Tighten to specification.

3. Install the screws and the new

Tightening Torque

elastic nuts on both sides of the

central body.

Self-tapping

5.5 ± 0.5 Nm

screws

(49 ± 4 lbf-in)

7. Install the self-tapping screws

around the fuel cap.

4. Tighten to specification.

Tiightening Torque

3.5 ± 0.5 Nm

M6 nuts

8. Tighten to specification.

(31 ± 4 lbf-in)

5. Install the self-tapping screws on

Tightening Torque

the front and the rear of central

Self-tapping

5.5 ± 0.5 Nm

body.

screws

(49 ± 4 lbf-in)

9. Reinstall the seat. Refer to Seat in

Equipment.

Trixx Modells

10. Install the rear footrests.

119

MAINTENANCE PROCEDURES

Ignition Coils

4. Connect ignition coil connector.

Removing the Ignition Coiil

Spark Plugs

1. To access the ignition coils, re-

Removiing the Spark Plug

move the central body. Refer to

Removing the Central Body

1. Remove the central body. Refer to

section.

Central Body.

2. Remove the ignition coils. Refer to

NOTICE

Removing the Ignition Coil.

3. Clean the spark plug and cylinder

Do not remove the ignition coill be-

head with compressed air.

fore diisconnecting the iinput con-

4. Unscrew the spark plug completely

nector or the wires may be

using a spark plug socket.

damaged. Do not pry on ignitiion

coil usiing any tool.

2. Disconnect ignition coil connector.

3. Remove ignition coil retaining

screw.

4. Remove ignition coil from spark

plug by rotating coils side to side

as you pull up.

1. Approved socket

2. Improper socket

5. Use the ignition coil to take spark

plug out of its hole.

Installling the Spark Pllug

Prior to installation, ensure the contact

1. Ignition coils

surfaces of the cylinder head and

spark plug are free of grime.

Installliing the Igniition Coiil

1. Using a wire feeler gauge, check

1. Align the retaining screw hole of

electrode gap as specified in Tech-

the ignition coil with the threaded

nical Specifications. Replace the

hole on the valve cover.

spark plug if not to specification.

2. Install the ignition coil on the spark

plug and push it all the way down

NOTICE

until it rests on the valve cover.

3. Install the retaining screw and

Do not adjust gap on thiis type of

tighten to specification below.

spark pllug. The adjustment coulld

weaken negative electrodes

Tiightening Torque

which may lead to electrode

breaking and severe engiine

Ignition coil

damage.

9 ± 1 Nm

retaining

(80 ± 9 lbf-in)

screw

121

MAINTENANCE PROCEDURES

2. Apply anti-seize lubricant on the

day or when the watercraft is stored

spark plug threads to prevent pos-

for any extended time.

sible seizure.

3. Hand screw spark plug into cylin-

NOTICE

der head. Then, tighten the spark

Faillure to flush the system, when

plug clockwise to the specified tor-

necessary, wiilll severelly damage

que with an approved spark plug

exhaust system. Make sure en-

socket.

gine operates during entiire

procedure.

Tighteniing Torque

13 ± 1 Nm

Spark plug

WARNING

(115 ± 9 lbf-in)

Perform these operations iin a well

4. Install the ignition coil. Refer to

ventillated area. Certaiin compo-

Ignition Coil.

nents in the engine compartment

5. Reinstall the central body. Refer to

may be very hot. Diirect contact

Central Body.

may result iin skin burn. Do not

touch any electrical part or jjet

Exhaust System

pump area when engiine is

runniing.

DANGER

DO NOT run the engiine iindoors or

WARNING

wiithout adequate ventillatiion or

When operating the engine whiile

permiit exhaust fumes to accumu-

the watercraft iis out of the water,

late iin confined areas. Engiine ex-

the heat exchanger may become

haust contaiins carbon monoxiide

very hot. Avoid any contact with

(CO) which, iif inhalled, can cause

heat exchanger as burns may

serious braiin damage or death.

occur.

Fllushiing the Exhaust System

1. Connect a hose to the connector

Flushing the exhaust system with

located at the rear of watercraft.

fresh water is essential to neutralize

Do not open water tap yet.

corroding effects of salt or other

chemical products present in water. It

will help to clean up sand, salt, shells

or other particles in water jackets and

hoses.

Exhaust system flushing should be

performed when the watercraft is not

expected to be used further the same

NOTE:

The following tool is recommended

when a quick connect adapter is used

to ease garden hose installation.

122

MAINTENANCE PROCEDURES

Recommended Tooll

NOTICE

Always close the water tap before

Flushing connector

stoppiing the engiine.

adapter

(P/N 295500473)

6. Disconnect the garden hose.

NOTICE

Remove fllushing connector

adapter after operatiion (iif used).

Heat Exchanger and Water

Intake Grate

Quick connect adapter

Flushing connector adapter

Inspectiing the Heat Exchanger and

Water Intake Grate

To flush the exhaust system, start

Inspect the heat exchanger and the jet

the engine then immediately open

pump water intake grate for damage.

the water tap.

Visit your Sea-Doo dealer to have any

damaged part repaired or replaced.

NOTICE

Allways start the engiine before

WARNING

openiing the water tap. Open

The tether cord must always be

water tap iimmediately after en-

removed from the engiine cut-off

gine is started to prevent over-

switch priior to iinspectiing the in-

heatiing. Never run engiine without

take grate.

suppllyiing water to the exhaust

system when watercraft is out of

water.

NOTE:

There is a reinforcement plate on LH

side of hull to maintain symmetry so

3. Run the engine about 20 seconds

the hydrodynamics of PWC is not

at a fast idle between 4000 - 5000

affected.

RPM.

NOTICE

Never run engiine llonger than 2

miinutes. Drive liine seal has no

coolling when watercraft is out of

water.

4. Ensure water flows out of jet pump

while flushing.

5. Close the water tap, run the engine

at 5000 RPM for 5 seconds and

stop the engine.

123

MAINTENANCE PROCEDURES

Tighteniing Torque

9 ± 1 Nm (80 ± 9 lbf-in)

Fuses

Fuse Location

All fuses are located inside a single

fuse box.

To access the fuse box, turn the knob

1/4 turn counter-clockwise, then pull

out to unsnap the rear portion and

slide rearward to remove.

1. Water intake

2. Heat exchanger

3. Reinforcement plate

Sacrificial Anode

Inspectiing the Sacrificiiall Anode

Sacrificial anode is located on

the

pump.

LH ACCESS COVER

1. To unlock, turn the knob

1/4

turn

counter-clockwise

The fuse box is located to the left of

the expansion tank.

To remove the fuse box cover,

squeeze and hold locking tabs on both

sides of the fuse box and pull the cov-

er off the fuse box.

1. Sacrificial anode location

Check the sacrificial anode for wear. If

worn more than half, replace it.

Removiing the Sacrificiall Anode

Unscrew sacrificial anode retaining

nut and remove anode.

Installling the Sacriifiicial Anode

Installation is the reverse of the re-

moval procedure.

124

MAINTENANCE PROCEDURES

LH ACCESS COVER

1. To lock, turn the knob 1/4 turn clockwise

1. Fuse box cover

2. Locking tabs

Inspectiing a Fuse

3. Expansion tank

Check fuse condition and replace it if

necessary.

WARNING

Never use a hiigher rated fuse

than specified.

To remove fuse from holder, pull fuse

out. Check if filament is melted.

TYPICAL - FUSE BOX COVER REMOVED

1. Fuse box

NOTE:

Fuse ratings and positions are illus-

trated on the fuse box cover.

To reinstall the fuse box cover and the

LH access cover, do the reverse of

the removal procedure and lock the

TYPICAL

knob by turning it 1/4 turn clockwise.

1. Fuse

2. Check if melted

3. Ampere rating

WARNING

If fuse burns out repeatedlly,

source of malfunction shoulld be

determined and corrected before

restartiing. Viisit an authoriized

Sea-Doo dealler for serviiciing.

125

WATERCRAFT CARE

Remove the watercraft from the water

Many marks, as shoes marks, can be

every day.

removed easily with this method.

Post-Operation Care

Body and Hull

Flushing the Exhaust System

Repaiir

The exhaust system should be

If any repairs are needed to body

flushed daily when watercraft is used

components or to the hull, contact

in salt or foul water.

your authorized Sea-Doo dealer.

Refer to Maintenance Procedures.

Cleaning

Wash the body and the hull with a

Additional Care for Foull Water or

soap and water solution (use only mild

Salt Water Operatiion

detergent). Rinse thoroughly with

When the watercraft is operated in

fresh water.

foul water and particularly in salt

water, additional care should be taken

Remove marine organisms from the

to protect the watercraft and its

inside and outside of the hull.

components.

NOTICE

Rinse watercraft bilge area with fresh

Never cllean using the folllowing

water.

products:

Never use a high pressure washer to

– XPS S4 Heavy Duty Clleaner

clean the bilge. USE LOW PRES-

– Strong detergent

SURE ONLY (such as a garden

– Degreasiing agent

hose).

– Ammoniia

– Acetone or other ketones

High pressure can cause damages to

– Allcohol

electrical or mechanical systems.

– Toluene or other aromatic

sollvents

CAUTION

– Chllorinated solvents

Alllow engiine to cooll before per-

– Mineral spiriits

forming any maiintenance.

– Paint thinners

– Petrolleum based products.

NOTICE

Stains may be removed from the seat

Faiilure to perform proper care

and fiberglass using the XPS All Pur-

such as: watercraft riinsiing, ex-

pose Cleaner and Degreaser or the

haust system fllushiing and antii-

equivalent.

corrosion treatment, when

watercraft is used iin sallt water,

To clean the carpets, use 3M™ Citrus

willl result in damage to the water-

Base Cleaner (24 oz spray can) or an

craft and its components. Never

equivalent.

leave the watercraft stored in dii-

rect sunliight.

WARNING

Never apply plastic or viinyll pro-

Seat Cleaning

tector on the carpets or seat as

the surface willl become sllippery

Before applying a cleaning product on

and the occupants may sllip off the

the seat, try removing marks with a

watercraft.

white eraser.

127

STORAGE AND PRESEASON PREPARATION

Storage

Inspectiing the Jet Pump

Visit your authorized Sea-Doo dealer.

WARNING

Fuel System

Because fuell and oiil are flamma-

ble, you shoulld have an author-

Protectiing the Fuel System

ized Sea-Doo dealer, repaiir shop,

or person of your own choosing to

A fuel stabilizer should be added in

inspect the fuel system iintegrity

the fuel tank to prevent fuel deteriora-

as specified in the periiodiic in-

tion and fuel system gumming. Follow

spection chart.

stabilizer manufacturers' instructions

for proper use.

It is recommended that the watercraft

Fill up fuel tank completely. Make sure

be serviced by an authorized Sea-Doo

there is no water inside fuel tank.

dealer, repair shop, or person of your

own choosing for storage, however

NOTICE

the following operations can be per-

Shoulld any water be trapped iin-

formed by you with a minimum of

siide fuel tank, severe internall

tools.

damage may occur to the fuel iin-

jectiion system.

NOTE:

Carry out the following tasks in the

same order as detailed in this section.

Engiine and Exhaust

Fllushiing the Exhaust System

NOTICE

Perform procedure as described in

Do not run the engiine duriing the

Maintenance Procedures section.

storage periiod.

Repllaciing the Engine Oill and Oiil

Fiilter

Propulsion System

The oil change and filter replacement

Clleaniing the Jet Pump

may be performed by an authorized

Sea-Doo dealer, repair shop, or per-

WARNING

son of your own choosing.

Allways remove tether cord from

the engine cut-off switch to pre-

Draining the Exhaust System

vent unexpected engiine startiing

1. The exhaust system is self drain-

before cleaning the jjet pump area.

ing, but the exhaust manifold

Engine must not be running for

needs to be drained to avoid dam-

this operation.

ages should the watercraft be

stored in an area where the tem-

perature attains the freezing point

Rinse the jet pump by spraying water

of water.

through its inlet and outlet openings.

2. Using the jet pump support con-

Spray an anti-corrosive product on the

nector or the flushing kit 295 100

propulsion system parts.

555 located at the rear of vehicle,

inject pressurized air (at 380 kPa

(55

lbf/in²)) in the system until

Serviice Product

there is no more water flowing

XPS Anti-Corrosive Lubricant or

from jet pump.

equivalent

129

STORAGE AND PRESEASON PREPARATION

Serviice Product

XPS Anti-Corrosive Lubricant or

equivalent

3. Fully depress the throttle lever. De-

pressing the throttle lever will pre-

vent fuel from being injected and

disable the ignition during engine

cranking.

4. Press the START/STOP button to

1. Jet pump support connector

crank the engine a few turns. This

will distribute the oil on the cylinder

walls.

5. Apply anti-seize lubricant on spark

plug threads, then reinstall them in

the engine. Refer to Maintenance

Procedures section.

6. Install the ignition coils. Refer to

Maintenance Procedures section.

Testing the Engiine Coolant Density

If antifreeze is not replaced, test its

WITH FLUSHING DEVICE KIT INSTALLED

density.

3. The following hose can be fabri-

cated to ease draining procedure.

The antifreeze replacement and a

density test should be performed by

an authorized Sea-Doo dealer, repair

shop or person of your own choosing.

Refer to Maintenance Schedule.

TYPICAL

NOTICE

1. Flushing adaptor 295 500 473, to be used

with flushing device kit

Improper antiifreeze density may

2. Hose 13 mm (1/2 in)

resullt iin freezing of the liiquid in

3. Air hose male adapter

the cooling system if the water-

craft is stored in an area where

the freeziing point iis attaiined. This

NOTICE

woulld seriously damage the

Faiilure to draiin the exhaust manii-

engiine.

fold may cause severe damage to

components.

Electrical System

Lubricatiing the Engine Cyllinders

Battery

1. Remove spark plugs. Refer to

Battery Maintenance

Maintenance Procedures section.

When storing the watercraft, the

2. Spray lubricant in each cylinder

through spark plug holes.

130

STORAGE AND PRESEASON PREPARATION

battery should always be stored in a

3. Reinstall bolts to secure retaining

warm, dry place.

nuts during removal.

4. Detach retaining strap.

WARNING

Never charge or boost the battery

whiile iinstallled iin the watercraft.

This vehicle is equipped with a main-

tenance-free type battery, there is no

need to add water to adjust electrolyte

level.

NOTICE

Never remove the battery strip

CENTRAL BODY REMOVED FOR CLARITY

PURPOSE

from caps or add electrollyte for

the llife of the battery.

1. BLACK (-) cable

2. RED (+) cable

3. Retaining strap

Battery Access

Turn the LH access cover knob 1/4

5. Remove the battery from the

turn counter-clockwise, then pull out

vehicle.

to unsnap the rear portion and slide

rearward to remove.

NOTICE

Shoulld any electrollyte spiilllage

occur, iimmediatelly wash off area

wiith a sollutiion of baking soda and

water, then riinse thoroughly.

LH ACCESS COVER

1. To unlock, turn the knob

1/4

turn

counter-clockwise

Removing the Battery

NOTICE

Cleaning the Battery

Allways disconnect the BLACK (-)

Clean battery casing and battery

battery cable first and reconnect

posts using a soft brush and a solution

llast.

of baking soda and water.

Remove corrosion from battery cable

1. Disconnect the BLACK (-) battery

terminals and battery posts using a

cable.

firm wire brush.

2. Slide the RED rubber protector off

the RED (+) cable terminal and

Rinse with clear water then dry well.

disconnect it from the battery post.

131

STORAGE AND PRESEASON PREPARATION

Inspectiing the Battery

minimum. Keep battery away from

dew, high moisture and direct

Visually inspect battery casing for

sunlight.

cracks, leaks or other possible

damages.

Recharge frequency depends on bat-

Discoloration, warping or raised top,

tery condition and storage tempera-

ture. Maintain battery as per following

indicates that the battery has over-

table.

heated or been overcharged.

If the casing is damaged, replace bat-

NOTE:

tery and thoroughly clean battery tray

The battery must always be stored in

and surrounding area with a water

fully a charged state.

and baking soda solution.

Ambiient

Chargiing

CAUTION

Temperature

Frequency

Shoulld the battery casing be dam-

aged, wear a suiitable pair of non--

Below16 °C (60

Every month

absorbent gloves when removing

°F)

the battery by hand.

Above16 °C (60

Every 2 weeks

°F)

Inspect the battery posts for security

of mounting.

Charging the Battery

Battery Storage

Use any automotive type battery

charger. Always refer to the battery

NOTICE

charger manufacturer’s instructions.

Battery storage iis criitiicall for bat-

tery liife. Regullarlly charging the

Installliing the Battery

battery during storage wiilll prevent

1. Install the battery in the watercraft

celll sullfatiion. Keeping the battery

and secure it using retaining strap.

in vehiiclle for storage may lead to

contacts degradation/corrosion

NOTICE

and case damage iif freeziing oc-

Allways diisconnect the BLACK (-)

curs. A discharged battery willl

battery cable first and reconnect

freeze and crack in areas where

last.

freeziing conditions are experi-

enced. Ellectrolyte leakage willl

damage surroundiing parts. Al-

2. Connect RED (+) cable.

ways remove battery from vehiiclle

3. Connect BLACK (-) cable last.

for storage and regularly recharge

4. Apply dielectric grease on battery

it to keep an optiimal condition.

posts.

5. Verify

cable

routing

and

attachments.

Clean the battery. Refer to Cleaning

6. Install

remaining

removed

the Battery.

components.

Apply a light coat of dielectric grease

on terminals.

Engine Compartment

Store battery in a cool dry place. Such

Clleaniing the Engine Compartment

conditions reduce self-discharging

1. Clean the bilge with hot water and

and keep fluid evaporation to a

detergent or with bilge cleaner.

132

STORAGE AND PRESEASON PREPARATION

2. Rinse thoroughly.

3. Lift front end of watercraft to com-

pletely drain bilge through the bilge

drain plugs.

Anticorrosiion Treatment

Wipe off any residual water in the en-

gine compartment.

Lubricate all metallic components in

engine compartment.

Serviice Product

Lubricant and anti-corrosive or

equivalent

NOTE:

The LH access panel and RH access

cover should be left partially open dur-

ing storage. This will prevent engine

compartment condensation and possi-

ble corrosion.

Body and Hulll

Repair, clean and protect the water-

craft as per procedures in Watercraft

Care section.

Preseason Preparation

The preseason preparation must be

performed in conjunction with the

Maintenance Schedule.

Ensure to perform all tasks included in

the Every Year or 100 Hours table.

Preseason preparation maintenance

may be performed by an authorized

Sea-Doo dealer, repair shop or per-

son of your own choosing.

133

WATERCRAFT IDENTIFICATION

The main components of the water-

craft (engine and hull) are identified by

different serial numbers. It may some-

times become necessary to locate

these numbers for warranty purposes

or to trace the watercraft in the event

of theft.

Hull Identification Number

The Hull Identification Number (HIN)

is engraved on the right hand side of

the hull at the rear of watercraft, above

the front of the sponson.

1. Engine Identification Number (EIN)

Engine Manufacturer

Identification

TYPICAL

1. Hull Identification Number (HIN)

It is composed of 12 digits:

YDV 12345 L 8 09

Model year

Year of production

1. Engine Manufacturer Identification

Month of production

Serial number

(a letter may also be used as a

digit)

Manufacturer

ENGINE MANUFACTURER IDENTIFICA-

TION LABEL

Engine Identification Number

The Engine Identification Number

(EIN) is located under the exhaust

manifold, close to cylinder number

one.

144

COMPLIANCE

EPA Compliance Label

EMISSION CONTROL SYSTEM INFORMATION

BOMBARDIER RECREATIONAL PRODUCTS INC.

THIS ENGINE CONFORMS TO

U.S. EPA & CALIFORNIA

EMISSIONS REGULATIONS FOR MARINE SI ENGINES.

RENSEIGNEMENT SUR LE DISPOSITIF ANTIPOLLUTION

CE MOTEUR EST CONFORME AUX NORMES

DE L’EPA

DES É.-U. POUR LES MOTEURS MARINS À ALLUMAGE COMMANDÉ.

ENGINE FAMILY / FAMILLE DE MOTEUR

( EPA

FEL)

CERTIFICATION STANDARDS

NORMES DE CERTIFICATION

(

FEL

)

EMISSION CONTROL SYSTEM

SYSTÈME DE CONTRÔLE DES ÉMISSIONS

MEETS

CALIFORNIA EVAP EMISSIONS REGULATIONS FOR SPARK

IGNITION MARINE WATERCRAFT. EVAP FAMILY

EVAPORATIVE EMISSION CONTROL SYSTEM: SO

SEE OPERATOR’S GUIDE FOR MAINTENANCE SCHEDULE AND FUEL,

OIL AND SPARK PLUG SPECIFICATIONS. VOIR LE CALENDRIER

D’ENTRETIEN ET LES SPÉCIFICATIONS D’ESSENCE, D’HUILE ET DE

BOUGIE D’ALLUMAGE DANS LE GUIDE DE L’OPÉRATEUR.

219905703

EPA COMPLIANCE LABEL (TYPICAL)

147

COMPLIANCE

Regulation Exemption Label

THIS BOAT IS MANUFACTURED BY BOMBARDIER RECREATIONAL

PRODUCTS INC. PER 46 U.S.C. 4305 AND U.S. COAST GUARD GRANT OF

EXEMPTION (CGB 88-001),THE COAST GUARD EXEMPTS THIS VESSEL

FROM ONE OR MORE SAFETY REGULATIONS. CGB 88-001 STATES

THAT CERTAIN REGULATIONS ARE INAPPLICABLE IN LIGHT OF THIS

VESSEL’S CHARACTERISTICS AND THAT THE EXEMPTION WILL NOT

HAVE AN ADVERSE EFFECT ON RECREATIONAL BOATING SAFETY.

THIS BOAT COMPLIES WITH U.S. COAST GUARD SAFETY STANDARDS

IN EFFECT ON THE DATE OF CERTIFICATION. ALL PERSONS SHOULD

WEAR A LIFEJACKET (PERSONAL FLOTATION DEVICE)

WHILE OPERATING OR RIDING ON THIS WATERCRAFT.

ASSEMBLED IN MEXICO

219905499

REGULATION EXEMPTION LABEL

148

RF D.E.S.S. KEY

This device complies with FCC Part 15 and Industry Canada license exempt

RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IC Registration Number: 12006A-1001317030

FCC ID: 2ACER-1001317030

We, the party responsible for compliance, declare under our sole responsibility

that the device is in conformity with the provisions of the following Council Direc-

tive: 2014/53/EU. To which this declaration relates is in conformity with the es-

sential requirements and other relevant requirements. The product is in

conformity with the following directives, harmonized standards and regulations:

Radio Equipment Directive (RED) 2014/53/EU and Harmonized Standards:

EN 300 330-2, EN 60950-1

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

This device contains licence-exempt transmitter (s)/receiver (s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS

(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique Can-

ada applicables aux appareils radio exempts de licence. L’exploitation est autori-

sée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage;

(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-

lage est susceptible d'en compromettre le fonctionnement.

150

BRP AUDIO SYSTEM

This equipment has been tested and

FCC ID: 22793-278004083

found to comply with the limits for a

Class B digital device, pursuant to

L’émetteur/ récepteur exempt de li-

Part 15 of the FCC rules. These limits

cence contenu dans le présent appa-

are designed to provide reasonable

reil

est

conforme aux CNR

protection against harmful interfer-

d’Innovation, Sciences et Développe-

ment économique Canada applica-

ence in a residential installation.

bles aux appareils radio exempts de

This equipment generates, uses, and

licence. L’exploitation est autorisée

can radiate radio frequency energy

aux deux conditions suivantes :

and, if not installed and used in ac-

(1) l'appareil ne doit pas produire de

cordance with the instructions, may

brouillage;

cause harmful interference to radio

communications. However, this is no

(2) l'appareil doit accepter tout brouil-

guaranty that interference will occur in

lage radioélectrique subi, même si le

a particular installation.

brouillage est susceptible d'en com-

promettre le fonctionnement.

If this equipment does cause harmful

interference to radio or television re-

Radio Equipment Directive

(RED)

ception, which can be determined by

2014/53/EU

and

Harmonized

turning the equipment off or on, you

Standards:

are encouraged to try to correct the in-

- ETSI EN 300 328 V2.1.1

terference by one or more of the fol-

(2016-11)

lowing measure:

- ETSI EN301 489-1 V2.1.1

- Reorient or relocate the receiving

(2017-02)

antenna.

- ETSI EN301 489-17 V3.1.1

- Increase the separation between

(2017-02)

the equipment and receiver.

- EN 62479:2010

- Connect the equipment to an out-

let on a different circuit than the

Mexiico

one to which the receiver is

connected.

IFETEL

- Consult the dealer or an experi-

Marca: BRP

enced radio/TV technician for help.

Modelo(s): 278004083

Changes or modifications not ex-

pressly approved by Mitek Corpora-

Número: BRBR2723-12845

tion could void the user's authority to

operate this equipment. This device

NOM-208-SCFI-2016

complies with Part

15 of the FCC

La operación de este equipo está su-

rules.

jeta a las siguientes dos condiciones:

Operation is subject to the following

(1) es posible que este equipo o dis-

two conditions:

positivo no cause interferencia perju-

dicial y (2) este equipo o dispositivo

(1) This device may not cause

debe aceptar cualquier interferencia,

harmful interference, and

incluyendo la que pueda causar su

(2) This device must accept any in-

operación no deseada.

terference received, including in-

terference that may cause

Braziil

undesired operation.

Registration

Number:

2AAOY-278004083

152

ENGINE EMISSIONS INFORMATION

Manufacturer''s

EPA Emission Regulations

Responsibility

Sea-Doo SIPME manufactured by

Manufacturers of marine engines

BRP are certified to the EPA as con-

must determine the exhaust emission

forming to the requirements of the reg-

levels for each engine horsepower

ulations for the control of air pollution

family and certify these engines with

from new SIPME. This certification is

the United States of America Environ-

contingent on certain adjustments

mental Protection Agency (EPA). An

being set to factory standards. For this

emissions control information label,

reason, the factory procedure for serv-

showing emission levels and engine

icing the product must be strictly fol-

specifications, must be placed on

lowed and, whenever practicable,

each Spark-Ignition Propulsion Marine

returned to the original intent of the

Engines

(SIPME) at the time of

design.

manufacture.

The responsibilities listed above are

general and in no way a complete list-

Dealer''s Responsibility

ing of the rules and regulations per-

When performing service on a Sea--

taining to the EPA requirements on

Doo SIPME that carry an emissions

exhaust emissions for marine prod-

control information label, adjustments

ucts. For more detailed information on

must be kept within published factory

this subject, you may contact:

specifications.

U. S. Environmental Protection

Replacement or repair of any emis-

Agency

sion related component must be exe-

Certification Division

cuted in a manner that maintains

Gasoline Engine Compliance Center

emission levels within the prescribed

2000 Traverwood Drive

certification standards.

Ann Arbor MI 48105

USA

Dealers are not to modify the engine

in any manner that would alter the

horsepower or allow emission levels

EPA INTERNET WEB SITE:

to exceed their predetermined factory

www.epa.gov/otaq

specifications.

Evaporative Emission

Exceptions include manufacturer's

Control System

prescribed changes, such as altitude

adjustments for example.

Spark-Ignition Marine Watercraft

(SIMW) sold in the State of California

Owner’s Responsibility

are certified to the California evapora-

tive emissions regulations for SIMW of

The owner/operator is required to

the California Air Resources Board

have engine maintenance performed

(13 CCR 2850 to 2869). These mod-

to maintain emission levels within pre-

els are equipped with an evaporative

scribed certification standards.

emission control system consisting of

Low Permeation Fuel Tank (LPFT),

The owner/operator is not to, and

Low Permeation Fuel Line (LPFL) and

should not allow anyone to modify the

a Pressure Relief Valve (PRV).

engine in any manner that would alter

the horsepower or allow emissions

levels to exceed their predetermined

factory specifications.

154

ENGINE

Rotax 900 ACE

Engiine

Type

Rotax 903

Rotax 900 ACE - 60

Rotax 900 ACE - 90

Model

4-stroke, Double Over Head

Camshaft (DOHC), dry sump,

liquid cooled

Rotax 900 ACE - 60

44.13 kW @ 7000 RPM

Declared Power⁽¹⁾

Rotax 900 ACE - 90

66.19 kW @ 8000 RPM

Induction

Naturally-aspirated

Number of cylinders

12 valves (self adjusting

Number of valves

hydraulic valve lifters)

74 mm

Bore

(2.9 in)

69.7 mm

Stroke

(2.7 in)

899.31 cm³

Displacement

(54.88 in³)

Compression ratio

11.0:1

Fuell System

Multipoint fuel injection with

iTC (intelligent Throttle

Fuel injection type

Control). Single throttle body

(46 mm) with actuator

Lubricatiion System

General

5W40 Synthetic

purpose

blend oil

Recommended

Engine oil

XPS oil

Warm

10W50 Synthetic oil

temperature

160

ENGINE

Use a 4-stroke SAE

motorcyclle engiine

oill compatiblle wiith

wet clutches

meeting or exceeding

the following

lubricant industry

specifications.

Alternate oil if XPS products are not

Always check the API

available

service label

certification on the oil

container, it must

contain at least one

of the indicated

standards.

API serviice

classiificatiion SN or

JASO-MA2

1.8 l

Capacity

(2.12 qt(liq.,US)) oil

change w/ filter⁽²⁾

Ellectriicall System

IDI (inductive discharge

Ignition

ignition)

Make and type

NGK CR8EB or equivalent

(3)

Spark plug

0.70 to 0.80 mm

Gap

(.028 to .031 in)

(1)

Declared power as per ISO 8665 at propeller-shaft.

(2)

Quantity required when changing engine oil. Total quantity for a dry

engine is 3.4 l (3.6 qt(liq.,US)).

(3)

NOTICE

Do not attempt to adjust gap on this spark plug.

161

VEHICLE

Spark Series

Cooliing System

Closed-loop cooling system

Type

(CLCS)

XPS Extended life pre-mixed

Recommended

coolant

Use a low silicate, extended

life ethylene-glycol premixed

Alternative, or if

coolant (50%-50%)

Coolant

not available

specifically formulated for

internal combustion

aluminum engines.

3.0 l

Capacity

(3.2 qt(liq.,US))

Fuell System

Fuel Pump

In-tank electrical

Regular unleaded

Type

Refer to Fuel Requirements

Fuel

87 Pump Posted AKI

(RON+MON)/2

Octane rating

(RON) E10

30 l

Full capacity

(7.9 gal(liq.,US))

Tank

Reserve

capacity

12 l

(from low level

(3.2 gal(liq.,US))

signal - approx.)

Electricall System

Battery

12 V, 18 Ah

ECM

7,5 A

Start/ Stop

Battery

15 A

Fuses

Charge

30 A

Acc Conn 12 V

7,5 A

Perm

162

VEHICLE

Acc Conn 12V

7,5 A

ACC

iBR (if

30 A

equipped)

Relay

RY1

Main

—

Propulsion

Propulsion system

Sea-Doo® jet pump

Axial flow, single stage.

Type

Large hub with double row

Jet pump

ball bearings

Material

Aluminum

Impeller

Stainless steel

Transmission

Type

Direct drive

Dimensions

Spark for 1 and

291 cm

(114.6 in)

Length

306 cm

Spark for 3

(120.6 in)

117 cm

Width

(46 in)

All Except Trixx

106 cm

Models

(41.6 in)

Height

107 cm

Trixx Models

(42.1 in)

Weight and Loadiing Capacity

Spark 900

188 kg

Spark for 2

ACE - 60

(414 lb)

Spark for 2 (w/

194 kg

Weight (dry)

convienance

(428 lb)

Spark 900

pkg and audio)

ACE - 90

195 kg

Spark for 3

(429 lb)

163

VEHICLE

Spark for 3 (w/

197 kg

convienance

(434 lb)

pkg)

Spark for 3 (w/

201 kg

convienance

(443 lb)

pkg and audio)

187 kg

Spark for 1

(412 lb)

Spark Trixx

197kg

Spark for 3

(434 lb)

1, 2* (refer to load limit)

Spark for 1

*with appropriate

passenger-ready seat sold as

Rider capacity

accessory.

Spark for 2

(refer to load limit)

Spark for 3

(refer to load limit)

Front bin (Convenience

42 l

Package for 2 and optional for

(11 gal(liq.,US))

Storage

other models)

capacity

2.7 l

Glove box

(.71 gal(liq.,US))

Load limit

160 kg

Spark for 1 and 2

(passenger(s)

(352 lb)

and luggage,

including

225 kg

Spark for 3

accessories)

(496 lb)

NOTE:

BRP reserves the right to make changes in design and specifications and/or to

make additions to, or improvements in its products without imposing any obliga-

tion upon itself to install them on its products previously manufactured.

164

TROUBLESHOOTING GUIDELINES

ENGINE WILL NOT START

1. Master swiitch opened.

- Close the master switch.

2. Tether cord removed.

- Press START/STOP button.

- Install tether cord cap over engine cut-off switch within 5 seconds after

depressing the START/STOP button.

- Press START/STOP button.

3. ECM does not recogniize the D.E.S.S. key.

- Refer to an authorized Sea-Doo dealer.

4. Burnt fuse: maiin, ellectric starter or ECM.

- Check wiring then replace fuse(s).

5. Diischarged battery.

- Refer to an authorized Sea-Doo dealer.

WARNING

Do not charge or boost the battery whille iinstallled on the watercraft.

Electrollyte iis poisonous and dangerous. Avoiid contact with eyes, skin

and clothing.

6. Battery connectiions, corroded or lloose. Bad ground.

- Refer to an authorized Sea-Doo dealer.

7. Water-fllooded engiine.

- Refer to Water-Flooded Engine in Special Procedures.

8. Faulty sensor or ECM.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

9. Seized jet pump.

- Try to clean. Otherwise, refer to an authorized Sea-Doo dealer.

ENGINE CRANKS SLOWLY

1. Loose battery cable connectiions.

- Check/clean/tighten.

2. Diischarged or weak battery.

- Refer to an authorized Sea-Doo dealer.

3. Worn starter.

- Refer to an authorized Sea-Doo dealer.

166

TROUBLESHOOTING GUIDELINES

ENGINE TURNS NORMALLY BUT WILL NOT START

1. Fuell tank empty or water-contaminated.

- Refill. Siphon and fill with fresh fuel.

2. Foulled/defectiive spark pllugs.

- Replace.

3. Blown fuse.

- Check wiring then replace fuse(s).

4. Water-fllooded engine.

- Refer to Water-Flooded Engine in Special Procedures.

5. Engiine management system faullt detected (check engine pillot llamp

is ON).

– Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

6. Faullty fuell system.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

ENGINE MISFIRES, RUNS IRREGULARLY

1. Foulled/defectiive/worn spark pllugs.

- Replace.

2. Fuell: Levell too llow, stalle or water-contamiinated.

- Siphon and/or refill.

3. Faullty iigniitiion coill(s).

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

4. Clogged injectors.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

5. Engiine management system faullt detected (check engine pillot llamp

is ON).

– Refer to Monitoring System.

167

TROUBLESHOOTING GUIDELINES

ENGINE SMOKE

1. Oill levell too hiigh.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

2. Water ingestiion, coollant lleak or damaged cyllinder head gasket.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

3. Internall engiine damage.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

ENGINE OVERHEATS

1. Cllogged exhaust cooliing system.

- Flush the exhaust cooling system.

2. Engine coollant level too low.

- Refer to Maintenance Procedures.

3. Quiick connect adapter lleft iin fllushiing connector.

- Remove adapter from flushing connector and retry watercraft. If

problem persists, seek service from an authorized Sea-Doo dealer,

repair shop, or person of your own choosing for maintenance, repair, or

replacement. Please refer to the US EPA Emission-Related Warranty

contained herein for information about warranty claims.

168

TROUBLESHOOTING GUIDELINES

ENGINE LACKS ACCELERATION OR POWER

Learning key used.

- Use a Normal key.

Not in Sport mode.

- Select Sport mode.

Jet pump water iintake cllogged.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

Damaged iimpelller or worn-out wear riing.

- Replace. Refer to an authorized Sea-Doo dealer.

Engiine oiil llevell too high.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

Weak spark.

- Refer to ENGINE MISFIRES, RUNS IRREGULARLY.

Engiine management system faullt detected (check engine pillot llamp

is ON).

– Refer to Monitoring System.

Clogged injectors.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

Low fuel pressure.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

10. Water iin fuell.

- Siphon and replace.

11. Engiine damaged by water ingestiion.

- Refer to an authorized Sea-Doo dealer.

169

TROUBLESHOOTING GUIDELINES

WATERCRAFT CAN NOT REACH TOP SPEED

1. Jet pump water intake clogged.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

2. Damaged impelller or worn-out wear ring.

- Replace. Refer to an authorized Sea-Doo dealer.

3. Engine management system fault detected (check engiine piilot lamp

is ON).

- Refer to Monitoring System.

WATERCRAFT STAYS IN NEUTRAL AFTER OPERATING THE iBR

LEVER

1. The iBR gate stays in neutrall.

- Release the throttle to idle RPM.

iBR WILL NOT RETURN TO NEUTRAL POSITION (iiBR INDICATOR

LIGHT ON)

1. iBR jjammed wiith debris.

- Clean and check for damage in the iBR gate and nozzle area.

2. iBR system malfunctiion.

- Remove tether cord, wait four minutes, reinstall key and check iBR light

to ensure fault is cleared.

- Refer to an authorized Sea-Doo dealer if fault persists or reoccurs

frequently.

iBR WILL NOT RETURN TO NEUTRAL POSITION (IBR INDICATOR

LIGHT OFF)

1. Throttle llever not fullly released during operation.

- Release throttle lever fully to ensure iBR gate returns to neutral.

2. Throttle llever does not fullly return to nulll when relleased.

- Refer to an authorized Sea-Doo dealer.

170

TROUBLESHOOTING GUIDELINES

ABNORMAL NOISE FROM PROPULSION SYSTEM

1. Weeds or debriis jammed around impelller.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

- Check for damage.

2. Damaged iimpelller shaft or drive shaft.

- Refer to an authorized Sea-Doo dealer.

3. Water iintrusion iin jjet pump causiing bearing seiizure.

- Refer to an authorized Sea-Doo dealer.

WATER FOUND IN BILGE

1. Billge pump system malfunction.

- Have system inspected by an authorized Sea-Doo dealer.

2. Exhaust system leak.

- Refer to an authorized Sea-Doo dealer.

3. Carbon riing at drive shaft worn.

- Refer to an authorized Sea-Doo dealer.

4. Hulll and/or Deck seal diispllaced or fasteners loose.

- Refer to an authorized Sea-Doo dealer.

171

MONITORING SYSTEM

A system monitors the electronic com-

then choose to call his authorized

ponents of the EMS (engine manage-

Sea-Doo dealer to pass on the fault

ment system) iBR, and other

code. The dealer will then advise the

components of the electrical system.

operator on the steps to take to solve

When a fault occurs, it sends visual

the problem, or to stop using the

messages through the information

watercraft and to bring it in to the deal-

center and/or audible signals through

er for repairs.

a beeper to inform you of a particular

condition.

Diispllayiing Faullt Codes

Select CODES. If a fault code has oc-

A fault code may also be recorded.

curred during your riding cycle, a CO-

When a minor or transient fault oc-

DES menu will be available in the

curs, the fault message and beeper

settings menu. Press OK to see the

will cease automatically if the condi-

list of faults.

tion that caused the fault does not ex-

ist anymore.

NOTE:

During normal riding conditions some

Releasing the throttle and letting the

fault codes may occur. Before con-

engine return to idle speed may allow

tacting your local dealer, remove the

normal operation to come back. If this

key, make sure to wait 2 minutes until

does not work, try removing and rein-

the electrical system shut down, then

stalling the tether cord on the engine

press start to wake up the electrical

cut-off switch.

system. This will ensure occurred fault

to disappear and only the active codes

The electronic system will react differ-

will remain ON in the CODES menu.

ently depending on the fault type. In

severe failure, the engine may not be

allowed to be started. In other cases,

the engine will operate in limp home

mode (reduced speed).

When a fault occurs, please refer to

the US EPA Emission-Related War-

ranty contained herein for information

about warranty claims.

Fault Codes

When a fault occurs, a numerical fault

code may be recorded depending on

the fault type and system.

These fault codes are used by author-

ized Sea-Doo dealers for trouble-

shooting the watercraft systems when

comparing them to a fault list.

Fault codes can be viewed in the infor-

mation center multifunction display

however, this function is only available

if a fault is still active.

If there is an active fault code, it may

be viewed by the operator on the mul-

tifunction display. The operator may

172

MONITORING SYSTEM

Indicator Lights and Message Display Information

The indicator lights (pilot lamps) and messages displayed in the information cen-

ter will inform you of a particular condition or if an anomaly occurs.

For information on usual indicator lights, refer to appropriate digital display.

Indiicator

Liight / Icon

Message Display

Descriiptiion

(ON)

LOW or HIGH

BATTERY

Low/high battery voltage

VOLTAGE

HIGH

Engine or exhaust system overheating

TEMPERATURE

CHECK ENGINE

Check engine (minor fault req. maint.) or

or LIMP HOME

LIMP HOME MODE (major eng. fault)

MODE

LOW OIL

Low oil pressure

PRESSURE

Light is steady with a buzzer and a

IBR MODULE

check engine light: iBR system fault

ERROR

(refer to an authorized Sea-Doo dealer)

Light is flashing: iBR system fault (refer

to an authorized Sea-Doo dealer)

Light is steady with no buzzer:

iBR system still functional but needs to

be inspected by an authorized Sea-Doo

dealer

Message Display

Descriiptiion

HIGH EXHAUST TEMPERATURE

High exhaust temperature detected

HIGH ENGINE TEMPERATURE

High engine temperature detected

Engine system malfunction and/or

CHECK ENGINE

requiring maintenance

Major fault detected, engine power

LIMP HOME MODE

limited

FUEL SENSOR FAULT

Fuel level sensor fault

WATER TEMP SENSOR

Problem with water temperature sensor,

DEFECTIVE

not sending water temperature info.

173

MONITORING SYSTEM

Beeper Code Information

Beeper Codes

Description

Bad D.E.S.S. system connection.

Reinstall tether cord cap correctly on the engine

cut-off switch.

Wrong D.E.S.S. key.

Use a tether cord that has been programmed for the

watercraft.

Defective D.E.S.S. key.

1 long beep

Use another tether cord with programmed D.E.S.S.

(while installing tether

key.

cord on watercraft

engine cut-off switch)

Defective engiine cut-off swiitch.

Refer to an authorized Sea-Doo dealer.

Improper operatiion of ECM or defective wiriing

harness.Seek service from an authorized Sea-Doo

dealer, repair shop, or person of your own choosing

for maintenance, repair, or replacement. Please

refer to the US EPA Emission-Related Warranty

contained herein for information about warranty

claims.

Engine management system faullt.

Seek service from an authorized Sea-Doo dealer,

repair shop, or person of your own choosing for

A 2 seconds beep

maintenance, repair, or replacement. Please refer to

every 15 minutes

the US EPA Emission-Related Warranty contained

interval

herein for information about warranty claims.

iBR system faullt.

Refer to an authorized Sea-Doo dealer.

A 2 seconds beep

Low fuell level.

every 10 minutes

Refill fuel tank. If problem persists, refer to an

interval

authorized Sea-Doo dealer.

175

MONITORING SYSTEM

Beeper Codes

Descriiptiion

High engiine temperature coollant.

See Engine Overheating.

Low oiil pressure.

Turn off engine as soon as possible. Check oil level

2 second beeps

and refill. Seek service from an authorized Sea-Doo

dealer, repair shop, or person of your own choosing

for maintenance, repair, or replacement. Please

refer to the US EPA Emission-Related Warranty

contained herein for information about warranty

claims.

High exhaust temperature.

Seek service from an authorized Sea-Doo dealer,

Constant beep

repair shop, or person of your own choosing for

(Stops when vehicle is

maintenance, repair, or replacement. Please refer to

turned OFF)

the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

NOTICE

If the moniitoriing beeper contiinuously sounds, stop engine as soon as

possiible.

176

BRP LIMITED WARRANTY – USA AND CANADA:

2024 SEA-DOO PERSONAL WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Sea-Doo per-

sonal watercraft (“Product (s)”) sold by authorized BRP Dealers (as hereinafter

defined) in the United States of America ("USA") and in Canada from defects in

material or workmanship for the period and under the conditions described

below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM STATE TO STATE, OR PROVINCE TO PROVINCE.

Neither the distributor, any BRP dealer nor any other person has been authorized

to make any affirmation, representation or warranty regarding the product, other

than those contained in this limited warranty, and if made, shall not be enforce-

able against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

- Normal wear and tear;

- Routine maintenance items, tune ups, adjustments;

- Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

- Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

178

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

resulting from repairs done by a person that is not an authorized servicing

BRP dealer;

- Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

- Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

- Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

- Damages from rust, corrosion or exposure to the elements;

- Damage resulting from water or snow ingestion;

- Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work;

- Damages from cooling system or jet pump blockage by foreign material; and

- Damages related to gel coat finish including but not limited to cosmetic gel

coat finish, blisters or fiberglass delamination caused by blisters, crazing, spi-

der or hairline cracks.

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWELVE (12) consecutive months, for private use owners.

2. FOUR (4) consecutive months, for commercial use owners.

A Product is used commercially when it is used in connection with any work or

employment that generates income during any part of the warranty period. A

Product is also used commercially when, at any point during the warranty period,

it is licensed for commercial use.

1. For emission-related components, please also refer to the US EPA Emis-

sion-Related Warranty.

2. For Sea-Doo personal watercrafts produced by BRP for sale in the State of

California or New York that are originally sold to a resident or subsequently

warranty registered to a resident in the State of California or New York,

please also refer to the applicable California and New York Emissions Control

Warranty Statement contained herein.

3. For Sea-Doo personal watercrafts produced by BRP for sale in the State of

California that are originally sold to a resident or subsequently warranty regis-

tered to a resident in the State of California, please also refer to the California

Evaporative Emissions Control System Warranty Statement contained

herein.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this limited warranty beyond its original expiration

date.

5) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

179

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

1. The Product must be purchased as new and unused by its first owner from a

Dealer authorized to sell the Products in the country in which the sale oc-

curred (“Dealer”);

2. The BRP specified pre-delivery inspection process must be completed, docu-

mented and signed by the purchaser;

3. The Product must have undergone proper registration by an authorized

Dealer;

4. The Product must be purchased in the country in which the purchaser

resides;

5. Routine maintenance outlined in the Operator’s Guide must be timely per-

formed in order to maintain warranty coverage. BRP reserves the right to

make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

6) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP dealer within three (3) days of the appearance of the

anomaly and provide the Dealer with reasonable access to the Product and rea-

sonable opportunity to repair it.

The customer must also present to the Dealer, proof of purchase of the Product

and must sign the repair/work order prior to starting the repair in order to validate

the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

7) WHAT BRP WILL DO

BRP’s obligations under this warranty are limited to, at its sole discretion, repair-

ing or replacing parts found defective under normal use, maintenance and serv-

ice without charge for parts and labor, at any authorized BRP dealer during the

warranty coverage period under the conditions described herein. No claim of

breach of warranty shall be cause for cancellation or rescission of the sale of the

Product to the owner.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

8) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

180

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

9) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized dealer's service manager or

owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

181

US EPA EMISSION-RELATED WARRANTY

Bombardier Recreational Products Inc. (“BRP”) warrants to the ultimate purchas-

er and each subsequent purchaser that this new engine, including all parts of its

exhaust emission-control system and its evaporative emission-control system,

meets two conditions:

1. It is designed, built, and equipped so it conforms at the time of sale to the ulti-

mate purchaser with the requirements of 40 CFR 1045 and 40 CFR 1060It.

2. It is free from defects in materials and workmanship that may keep it from

meeting the requirements of 40 CFR 1045 and 40 CFR 1060.

Where a warrantable condition exists, BRP will repair or replace, as it elects, any

part or component with a defect in materials or workmanship that would increase

the engine’s emissions of any regulated pollutant within the stated warranty peri-

od at no cost to the owner, including expenses related to diagnosing and repair-

ing or replacing emission-related parts. All defective parts replaced under this

warranty become the property of BRP.

For all emission-related warranty claims, BRP is limiting the diagnosis and repair

of emission-related parts to the authorized Sea-Doo dealers, unless for emer-

gency repairs as required by item 2 of the following list.

As a certifying manufacturer, BRP will not deny emission-related warranty claims

based on any of the following:

1. Maintenance or other service BRP or BRP's authorized facilities performed.

2. Engine/equipment repair work that an operator performed to correct an un-

safe, emergency condition attributable to BRP as long as the operator tries to

restore the engine/equipment to its proper configuration as soon as possible.

3. Any action or inaction by the operator unrelated to the warranty claim.

4. Maintenance that was performed more frequently than BRP specify.

5. Anything that is BRP fault or responsibility

6. The use of any fuel that is commonly available where the equipment operates

unless BRP written maintenance instructions state that this fuel would harm

the equipment’s emission control system and operators can readily find the

proper fuel. See maintenance information section and fuel requirements of fu-

eling section.

Emission-Related Warranty Period

The emission-related warranty is valid for the following period whichever comes

first:

Hours

Months

Exhaust

175

emission-related

components

Evaporative

N/A

emission-related

components

182

US EPA EMISSION-RELATED WARRANTY

Components Covered

The emission-related warranty covers all components whose failure would in-

crease an engine’s emissions of any regulated pollutant, including the following

listed components:

For exhaust emissions, emission-related components include any engine

parts related to the following systems:

- Air-induction system

- Fuel system

- Ignition system

- Exhaust gas recirculation systems

The following parts are also considered emission-related components for ex-

haust emissions:

- Aftertreatment devices

- Crankcase ventilation valves

- Sensors

- Electronic control units

The following parts are considered emission-related components for evapora-

tive emissions:

- Fuel tank

- Fuel cap

- Fuel line

- Fuel line fittings

- Clamps*

- Pressure relief valves*

- Control valves*

- Control solenoids*

- Electronic controls*

- Vacuum control diaphragms*

- Control cables*

- Control linkages*

- Purge valves

- Vapor hoses

- Liquid/ vapor separator

- Carbon canister

- Canister mounting brackets

- Carburetor purge port connector

NOTE:

* As related to the evaporative emission control system.

4. Emission-related components also include any other part whose only purpose

is to reduce emissions or whose failure will increase emissions without signifi-

cantly degrading engine/ equipment performance.

Limited Applicability

As a certifying manufacturer, BRP may deny emission-related warranty claims

for failures that have been caused by the owner’s or operator’s improper mainte-

nance or use, by accidents for which the manufacturer has no responsibility, or

183

US EPA EMISSION-RELATED WARRANTY

by acts of God. For example, an emission-related warranty claim need not be

honored for failures that have been directly caused by the operator’s abuse of

the engine/ equipment or the operator’s use of the engine/equipment in a manner

for which it was not designed and are not attributable to the manufacturer in

anyway.

If you have any question regarding your warranty rights and responsibility or for

the name and location of the nearest authorized BRP dealer, you should contact

BRP by filling out the customer contact form at www.brp.com or contact BRP by

mail at one of the addresses listed under the CONTACT US section of this guide,

or call at 1-888-272-9222.

184

CALIFORNIA EVAPORATIVE EMISSIONS

CONTROL SYSTEM WARRANTY STATEMENT

Your Warranty Rights and Obligations

The California Air Resources Board is pleased to explain the evaporative emis-

sions control system’s warranty on your 2024 spark-ignition marine watercraft

(SIMW). In California, new spark-ignition marine watercraft must be designed,

built, and equipped to meet the State’s stringent anti-smog standards. Bombar-

dier Recreational Products Inc. must warrant the evaporative emissions control

system on your spark-ignition marine watercraft for the period listed below, pro-

vided there has been no abuse, neglect or improper maintenance of your spar-

k-ignition marine watercraft.

Your evaporative emissions control system may include parts such as: canisters,

carburetors, clamps, connectors, filters, fuel caps, fuel lines, fuel tanks, valves,

vapor hoses, and other associated evaporative emissions control system

components

Manufacturer’s Warranty Coverage

This evaporative emissions control system is warranted for two years. If any

evaporative emission-related part on your spark-ignition marine watercraft is de-

fective, the part will be repaired or replaced by Bombardier Recreational Prod-

ucts Inc.

Parts covered:

1. Clamp(s)*

2. Fuel Cap

3. Fuel Line(s)

4. Fuel Line Fitting(s)

5. Fuel Tank

6. Pressure Relief Valve(s)*

7. Vapor Hose(s)

8. All other parts not listed that may affect the evaporative emissions control

system

NOTE:

* As related to the evaporative emission control system.

Owner’s Warranty Responsibilities

As the spark-ignition marine watercraft owner, you are responsible for perform-

ance of the required maintenance listed in your owner’s manual. Bombardier

Recreational Products Inc. recommends that you retain all receipts covering

maintenance on your spark-ignition marine watercraft, but Bombardier Recrea-

tional Products Inc. cannot deny warranty solely for the lack of receipts.

As the spark-ignition marine watercraft owner, you should however be aware that

Bombardier Recreational Products Inc. may deny you warranty coverage if your

spark-ignition marine watercraft or a part has failed due to abuse, neglect, im-

proper maintenance or unapproved modifications.

You are responsible for presenting your spark-ignition marine watercraft to a

Bombardier Recreational Products Inc. distribution center or service center as

185

CALIFORNIA AND NEW YORK EMISSION

CONTROL WARRANTY STATEMENT FOR MODEL

YEAR 2024 SEA-DOO® PERSONAL WATERCRAFT

Your Warranty Rights and Obligations

The California Air Resources Board, the New York State Department of Environ-

mental Conservation and Bombardier Recreational Products Inc. ("BRP") are

pleased to explain the emission control system warranty on your Model Year

2024 Sea-Doo personal watercraft. In California and New York, new personal

watercraft engines must be designed, built and equipped to meet the State’s

stringent anti-smog standards. BRP must warrant the emission control system

on your personal watercraft engine for the period of time listed below provided

there has been no abuse, neglect or improper maintenance of your watercraft

engine.

Your emission control system may include parts such as the fuel injection sys-

tem, the ignition system and catalytic converter. Also included may be hoses,

belts, connectors and other emission related assemblies.

Where a warrantable condition exists, BRP will repair your personal watercraft

engine at no cost to you including diagnosis, parts and labor provided that such

work is performed by an authorized BRP dealer.

Manufacturer’s Limited Warranty Coverage

This emission limited warranty covers Model Year 2024 Sea-Doo personal water-

crafts certified and produced by BRP for sale in California or New York, that are

originally sold in California or New York to a California or New York resident or

subsequently warranty registered to a California or New York resident. The BRP

limited warranty conditions for Sea-Doo personal watercrafts are still applicable

to these models with the necessary modifications. Select emission control parts

of your 2024 Sea-Doo personal watercraft are warranted from the date of deliv-

ery to the first retail consumer for a period of 4 years, or for 250 hours of use,

whichever occurs first. However, warranty coverage based on the hourly period

is only permitted for personal watercraft equipped with the appropriate hour me-

ters or their equivalent. If any emission-related part on your engine is defective

under warranty, the part will be repaired or replaced by BRP.

Parts Covered for a Model Year 2024 Sea-Doo Personall Watercraft

Supercharger

Air intake adapter

Throttle position sensor

Spark plugs

Intake manifold air pressure sensor

Ignition coils

Intake manifold air temperature

Air box

sensor

Engine temperature sensor

Intake and exhaust valve and seals

Knock sensor

Intake manifold

187

CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2024

SEA-DOO® PERSONAL WATERCRAFT

Engine control module ECM

Crankcase ventilation valve

Throttle body

Throttle body seal

Ful rail

Intake manifold seal

Fuel injectors

Wire harness and connectors

Fuel pressure regulator

Fuel filter

Fuel pump

The emission warranty covers damage to other engine components that is

caused by the failure of a warranted part. The BRP operator’s guide provided

contains written instructions for the proper maintenance and use of your personal

watercraft. All emission warranty parts are warranted by BRP for the entire war-

ranty period of the personal watercraft, unless the part is scheduled for replace-

ment as required maintenance in the operator’s guide.

Emission warranty parts that are scheduled for replacement, as required mainte-

nance, are warranted by BRP for the period of time before the first scheduled re-

placement date for that part. Emission warranty parts that are scheduled for

regular inspection, but not regular replacement, are warranted by BRP for the en-

tire warranty period of the personal watercraft. Any emission warranty part re-

paired or replaced under the terms of this warranty statement is warranted by

BRP for the remainder of the warranty period of the original part. All parts re-

placed under this limited warranty become the property of BRP

Maintenance receipts and records should be transferred to each subsequent

owner of the personal watercraft.

Owner’’s Warranty Responsiibillities

As the owner of a 2024 Sea-Doo personal watercraft, you are responsible for the

performance of the required maintenance listed in your operator’s guide. BRP

recommends that you retain all receipts covering maintenance of your personal

watercraft engine, but BRP cannot deny warranty solely for the lack of receipts or

your failure to ensure the performance of all scheduled maintenance

As the owner of a Sea-Doo personal watercraft, you should however be aware

that BRP may deny your warranty coverage if your engine or a part has failed

due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your engine to an authorized BRP Sea-Doo

dealer as soon as a problem exists. The warranty repairs will be completed in a

reasonable amount of time, not to exceed 30 days

If you have any questions regarding your warranty rights and responsibilities or

for the name and location of the nearest authorized BRP Sea-Doo dealer you

should contact the Customer Assistance Center at 1-888-272-9222.

188

CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2024

SEA-DOO® PERSONAL WATERCRAFT

Star Rating System

For California and New York, your 2024 Sea-Doo watercraft (SIMW) has a spe-

cial environmental label required by the California Air Resources Board. The la-

bel has 3 stars. A hangtag, provided with the Product (SIMW), describes the

meaning of the star rating system.

The Star Label Means Clleaner Marine Engiines

The Symbol for Cleaner Marine Engines:

Clleaner Air and Water

For a healthier lifestyle and environment.

Better Fuel Economy

Burns up to 30 - 40 percent less gas and oil than conventional carbureted two-s-

troke engines saving money and resources.

Longer Emiissiion Warranty

Protects consumer for worry free operation.

One Star – Low Emission

The one-star label identifies personal watercraft, outboard, stern drive and in-

board engines that meet the Air Resources Board’s Personal Watercraft and Out-

board marine engine 2001 exhaust emission standards. Engines meeting these

standards have 75% lower emissions than conventional carbureted two-stroke

engines. These engines are equivalent to the U.S. EPA’s 2006 standards for ma-

rine engines.

Two Stars – Very Low Emiissiion

The two-star label identifies personal watercraft, outboard, stern drive and in-

board engines that meet the Air Resources Board’s Personal Watercraft and Out-

board marine engine 2004 exhaust emission standards. Engines meeting these

standards have 20% lower emissions than One Star - Low-Emission engines.

Three Stars – Ulltra Low Emiissiion

The three-star label identifies engines that meet the Air Resources Board’s Per-

sonal Watercraft and Outboard marine engine 2008 exhaust emission standards

or the Stern drive and Inboard marine engine 2003 exhaust emission standards.

Engines meeting these standards have 65% lower emissions than One Star -

Low Emission engines.

Four Stars – Super Ulltra Low Emiissiion

189

BRP INTERNATIONAL LIMITED WARRANTY: 2024

SEA-DOO® WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Sea-Doo

watercraft (“Product(s)”) sold by distributors or dealers authorized by BRP to dis-

tribute the Products outside of the United States of America ("USA"), Canada,

member states of the European Economic Area (which is comprised of the states

of the European Union plus the United Kingdom, Norway, Iceland and Liechten-

stein) ("EEA"), Turkey, member states of the Commonwealth of the Independent

States (including Ukraine and Turkmenistan) ("CIS") from defects in material or

workmanship for the period and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM COUNTRY TO COUNTRY. BRP SHALL NOT BE HELD LIABLE IF

PRODUCTS OR WARRANTY PARTS ARE NOT AVAILABLE IN CERTAIN

COUNTRIES FOR REASONS OUTSIDE OF BRP’S CONTROL.

For Products purchased in Australia, refer to the Australia-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

191

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

Damages from rust, corrosion or exposure to the elements;

–

Damage resulting from water or snow ingestion;

–

Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work;

Damages from cooling system or jet pump blockage by foreign material;

–

Damages to gel coat finish including but not limited to cosmetic gel coat finish

defects, blisters, starring, crazing and fiberglass delamination caused by blis-

ters, crazing, spider or hairline cracks.

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWELVE (12) consecutive months, for private use owners. For AUSTRALIA

and NEW ZEALAND only, TWENTY-FOUR (24) consecutive months for pri-

vate, recreational use.

2. FOUR (4) consecutive months, for commercial use owners. A Product is used

commercially when it is used in connection with any work or employment that

generates income during any part of the warranty period. A Product is also

used commercially when, at any point during the warranty period, it is li-

censed for commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty

period which can be extended by any applicable warranty promotional program,

as the case may be.

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

192

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

FOR PRODUCTS SOLD IN AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensa-

tion for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

Nothing in these Warranty terms and conditions should be taken to exclude, re-

strict or modify the application of any condition, warranty, guarantee, right or rem-

edy conferred or implied under the Competition and Consumer Act 2010 (Cth),

including the Australian Consumer Law or any other law, where to do so would

contravene that law, or cause any part of these terms and conditions to be void.

The benefits given to you under this limited warranty are in addition to other rights

and remedies that you have under Australian law.

5) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

A) The Product must be purchased as new and unused by its first owner

from a Distributor/Dealer authorized to distribute Products in the country in

which the sale occurred (“Distributor/Dealer”);

B) The BRP specified pre-delivery inspection process must be completed,

documented and signed by the purchaser;

C) The Product must have undergone proper registration by an authorized

Distributor/Dealer;

D) The Product must be purchased in the country in which the purchaser

resides;

E) Routine maintenance outlined in the Operator’s Guide must be timely

performed in order to maintain warranty coverage. BRP reserves the right

to make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

6) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

193

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

All parts replaced under this limited warranty become the property of BRP.

7) WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

8) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

9) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

194

BRP LIMITED WARRANTY FOR THE EUROPEAN

ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024

SEA-DOO® PERSONAL WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Sea-Doo per-

sonal watercraft (“Product(s)”) sold by distributors or dealers authorized by BRP

to distribute the Products in member states of the European Economic Area

(which is comprised of the states of the European Union plus the United King-

dom, Norway, Iceland and Liechtenstein) ("EEA"), Turkey, member states of the

Commonwealth of the Independent States (including Ukraine and Turkmenistan)

("CIS") (“Distributor/Dealer”) from defects in material or workmanship for the peri-

od and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM STATE TO STATE, OR PROVINCE TO PROVINCE. BRP SHALL NOT

BE HELD LIABLE IF PRODUCTS OR WARRANTY PARTS ARE NOT AVAIL-

ABLE IN CERTAIN COUNTRIES FOR REASONS OUTSIDE OF BRP’S

CONTROL.

For Products purchased in France, refer to the France-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

195

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

Damages from rust, corrosion or exposure to the elements;

–

Damage resulting from water or snow ingestion;

–

Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work.

Damages from cooling system or jet pump blockage by foreign material;

–

Damages to gel coat finish including but not limited to cosmetic gel coat finish

defects, blisters, starring, crazing and fiberglass delamination caused by blis-

ters, crazing, spider or hairline cracks

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWENTY-FOUR (24) consecutive months, for private, recreational use.

2. FOUR (4) consecutive months, for commercial use owners. A Product is used

commercially when it is used in connection with any work or employment that

generates income during any part of the warranty period. A Product is also

used commercially when, at any point during the warranty period, it is li-

censed for commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty

period which can be extended by any applicable warranty promotional program,

as the case may be.

196

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

5) FOR PRODUCTS SOLD IN FRANCE ONLY

The seller shall deliver goods that are complying with the contract and shall be

responsible for defects existing upon delivery. The seller shall also be responsi-

ble for defects resulting from packaging, assembling instructions or the installa-

tion when it is its responsibility per the contract or if accomplished under its

responsibility. To be compliant with the contract, the good shall:

1. Be fit for normal use for goods similar thereto and, if applicable:

- Correspond to the description provided by the seller and have the qualities

presented to the buyer though sample or model;

- Have the qualities that a buyer may legitimately expect considering the

public declarations of the seller, the manufacturer of its representative, in-

cluding in advertising or labeling; or

2. Have the characteristics mutually agreed upon as between the parties or be

fit for the specific use intended by the buyer and brought to the attention of

the seller and which accepted.

The action for failure to comply is prescribed after two years after delivery of the

goods. The seller is responsible for the warranty for hidden defects of the good

sold if such hidden defects are rendering the good unfit for the intended use, or if

they diminish its use in such a way that the buyer would not have acquired the

good or would have given a lesser price, had he known. The action for such hid-

den defects shall be taken by the buyer within 2 years of the discovery of the

defect.

6) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

A) The Product must be purchased as new and unused by its first owner

from a Distributor/Dealer authorized to distribute Products in the country (or

in the case of the EEA, union of countries) in which the sale occurred (“Dis-

tributor/Dealer”);

B) The BRP specified pre-delivery inspection process must be completed,

documented and signed by the purchaser;

C) The Product must have undergone proper registration by an authorized

Distributor/Dealer;

D) The Product must be purchased in the country (or in the case of the

EEA, union of countries) in which the purchaser resides;

E) Routine maintenance outlined in the Operator’s Guide must be timely

performed in order to maintain warranty coverage. BRP reserves the right

to make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

197

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

7) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

8) WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, or for

EEA residents, if service is required outside of the EEA, the owner will bear re-

sponsibility for any additional charges due to local practices and conditions, such

as, but not limited to, freight, insurance, taxes, license fees, import duties, and

any and all other financial charges, including those levied by governments,

states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

9) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

10) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

198

DATA PRIVACY INFORMATION

Bombardier Recreational Products inc., its affiliates and subsidiaries (“BRP”) is

committed to protecting your privacy and support a general policy of openness

about how we collect, use and disclose your personal information in the course

of managing our relationship with you. More detaiils can be found by visiting

BRP’’s Priivacy Poliicy at:

https://brp.com/en/privacy-poliicy.htmll or by scanniing the QR Code below.

Please be assured that we have appropriate security measures in place to en-

sure that your personal information is protected against loss and unauthorized

access.

Your personal information that may be collected by BRP, directly from you or

from authorized dealers or authorized third parties, includes:

- Contact, Demographiic & Registratiion Informatiion (e.g., name, full ad-

dress, phone number, email, gender, ownership history, language of

communication)

- Vehicle Information (e.g., serial number, purchase and delivery date, unit

usage, vehicle location and movements)

- Third Party Informatiion (e.g., information received from BRP partners, join-

t-marketing activities information, social media)

- Technological Information (e.g., IP address, type of device, operating sys-

tem, browser type, webpages you view, cookies and similar technologies

when you use BRP or dealers’ websites or mobile application)

- Interaction with BRP Information (e.g., information collected when you call

BRP’s in-house sales representatives, buy items on a BRP web Site, sign up

for BRP emails, participate in BRP-sponsored contests and sweepstakes or

attend BRP-sponsored events)

- Transactiionall Informatiion (e.g., information necessary to handle returns,

payment information when you purchase our products or services through

our websites or mobile applications and other issues related to your purchase

of BRP products)

This information may be used and processed for the following purposes:

- Safety & Security

- Customer Support for Sales & After Sales (e.g., complete or follow up with

you about your purchase or maintenance)

- Registration & Warranty

- Communication (e.g., sending you a BRP satisfaction survey)

- Online Behavioural Advertising, Profiling and Location-Based Services

(e.g., offer customized experience)

- Compliance & Dispute Resolution

- Marketing & Advertising

- Assistance (e.g., help with any delivery issues, handle returns, and other is-

sues related to your purchase of BRP products).

We also may use personal information to generate aggregated or statistical data

that no longer identifies you personally.

Your personal informatiion may be disclosed to the folllowiing: BRP, BRP’s

authoriized deallerships, diistriibutors, serviice proviiders, advertising & mar-

ket research partners and other authoriized third partiies.

We may receive information about you from diverse sources, including third par-

ties, such as BRP’s authorized dealerships and partners, with whom we offer

200

DATA PRIVACY INFORMATION

services or engage in joint-marketing activities. We may also receive information

about you from social media platforms such as Facebook and Twitter, when you

interact with us on those platforms.

Depending on the circumstances, your personal information may be communi-

cated outside the region where you reside. Your personal information is retained

only for as long as necessary for the purpose for which we obtained it and ac-

cording to our retention policies.

To exercise your data privacy rights (e.g. right of access, right of rectification), to

withdraw your consent in order to be removed from the address list for marketing

purposes or for the satisfaction survey or for general data privacy questions,

please contact BRP’s Data Protection Officer at or by mail at privacyoffii-

cer@brp.com or by mail at:

BRP Legal Service, 726 St-Joseph, Valcourt, Quebec, Canada, J0E 2L0.

When BRP processes your personall iinformation, they do so in complliance

wiith its Privacy Pollicy avaiilable at: https://www.brp.com/en/privacy-poliicy.

htmll or by using the folllowiing

QR Code.

201

www.brp.com

Asia Pacific

Australia

Level 26

477 Pitt Street

Sydney, NSW 2020

China

上海市徐汇区衡山路10号6号楼301

Rm 301, Building 6,

No.10 Heng Shan Rd,

Shanghai, China

Japan

21F Shinagawa East One Tower

2-16-1 Konan, Minato-ku-ku,

Tokyo 108-0075

New Zealland

Suite 1.6, 2-8 Osborne Street,

Newmarket, Auckland 2013

Europe, Middle East and Africa

Bellgium

Oktrooiplein 1

9000 Gent

Czech Republiic

Stefanikova 43a

Prague 5

150 00

Germany

Itterpark 11

40724 Hilden

Fiinland

Isoaavantie 7

PL 8040

96101 Rovaniemi

France

Arteparc Bâtiment B

Route de la côte d'Azur,

13 590 Meyreuil

Norway

Ingvald Ystgaardsvei 15

N-7484 Trondheim

202

BRP Sea-Doo SPARK SERIES. OPERATOR’S GUIDE (2024) - page 2