BRP Sea-Doo FISHPRO SPORT AND TROPHY SERIES. OPERATOR’S GUIDE (2024)

OPERATING INSTRUCTIONS

When operating in reverse, turn the

Braking

handlebar in the opposite direction

that you want to move the rear of the

WARNING

watercraft.

The engine must be runniing to be

For example, to steer the rear of the

ablle to use the brake.The brake is

watercraft to port (left), turn the han-

onlly appliicable when operatiing iin

dlebar to starboard (right).

forward movement, it has no ef-

fect on rearward vellociity.The

brake cannot prevent your water-

craft from drifting due to current or

wiind.

The braking function can only be en-

gaged during forward operation at or

above the threshold speed of 14 km/h

(9 MPH).

Braking is engaged and controlled

when the iBR lever on the LH handle-

bar is pulled in at least

25% of its

travel.

WARNING

Brakiing shoulld be practiced iin

open waters and at graduallly iin-

creasiing speeds iin order to be-

come fullly familliar with the

controlls and watercraft handlling

TYPICAL

- STEERING DIRECTION

RE-

characteristics.

VERSED WHEN BACKING

When iBR lever is applied, the throttle

lever command is overridden and en-

CAUTION

gine throttle control is now dependant

Steering directiion in reverse

on the iBR lever position. Braking can

thrust is opposite of forward

thus be modulated by using only the

thrust. To steer the stern to port

iBR lever.

(lleft) in reverse, turn the handle-

bar to starboard (right). To steer

Watercraft deceleration is proportional

the stern to starboard (right), turn

to the braking force. The more the iBR

the handlebar to port (left). Re-

lever is pulled in, the greater the brak-

verse thrust operation should be

ing force applied. The deceleration is

practiiced in open waters iin order

also related to the total weight on the

to become fullly familliar with the

watercraft. A fully loaded watercraft

controls and watercraft handliing

(cargo and passengers) will not decel-

characteriistiics before operatiing iin

erate as fast as it could without this

close quarters.

load.

121

OPERATING INSTRUCTIONS

proportional to the throttle lever

position.

NOTE:

Be careful to gradually actuate the

WARNING

iBR lever to adjust intensity of the

braking force and simultaneously re-

If forward accelleration iis not de-

lease the throttle lever.

sired when the brake llever iis re-

leased, release the throttle lever.

CAUTION

When braking, riders must brace

WARNING

themsellves against the decelera-

It iis important to inform other op-

tiion force to prevent from moviing

erators who iintend to folllow iin a

forward on the watercraft and los-

convoy formation of the braking

iing ballance. The operator shoulld

and maneuveriing capabiiliity of

allways keep both hands on the

your vehiicle and that a greater

handlebars, and alll passengers

distance should be maintained.

should maintain a firm griip on

their seat and/or the hand raill.

Brakiing in a Turn

Throttle must be applied for turning to

WARNING

ensure directional control. However

Stopping distance willl vary de-

braking can be initiated during a turn

pending on initiall speed, load,

using the iBR lever as previously de-

wiind, number of riders, water con-

scribed. Get ready to maintain your

diitions, and the amount of braking

balance while the wake is crossing

power commanded by the opera-

your watercraft.

tor. Allways adjjust your riidiing style

accordiinglly.

CAUTION

As the watercraft slows to a stop

When the watercraft slows to less

whiile brakiing in a turn, the wake

than 14 km/h (9 MPH), braking mode

created by the watercraft will

ends and reverse mode is engaged.

catch up and tend to push the

Release the iBR lever once the water-

watercraft siideways. Be prepared

craft is stopped. Otherwise, a rear-

to maiintaiin ballance as the wake

ward movement will be initiated.

crossed the watercraft.

CAUTION

Variable Trim System (VTS)

As the watercraft slows to a stop,

the wake created by the water-

The variable trim system

(VTS)

craft wiilll catch up and tend to

changes the vertical position of the jet

pump nozzle to provide the operator

push the watercraft forward. En-

with a fast, effective system to com-

sure there are no obstacles or

pensate for load, thrust, riding position

bathers iin the directiion of travell.

and water conditions. Correctly ad-

justed, it can improve handling, re-

If the throttle lever is still pulled in

duce porpoising, and position the

when releasing the iBR lever, the

watercraft at its best riding attitude to

watercraft will accelerate forward after

attain maximum performance.

a short delay. Acceleration will be

When first using the watercraft, the

operator should become familiar with

122

OPERATING INSTRUCTIONS

the use of the variable trim system

VTS Triimmiing Methods

(VTS) at varying speeds and water

conditions. A mid-range trim is gener-

Avaiilablle VTS

ally used when cruising. Experience

trimming

FishPro

alone will dictate the best trim for the

methods

conditions. During the watercraft

VTS trim button

break-in period, when lower speeds

are recommended, it is an excellent

VTS "double

opportunity to become familiar with

cliick" triimmiing

trim adjustment and its effects.

Launch Control

When the nozzle is positioned in an

upward angle, the water thrust directs

Extended VTS

the bow of the watercraft upward. This

position is used to optimize high

X = Indicates a standard feature

speed.

- = See a Sea-Doo dealer for

availability.

When the nozzle is directed down-

ward, the bow is forced downward

and increases the watercraft turning

Adjjusting the VTS

capabilities. As with any watercraft,

Nine trim positions are available.

speed and operator body position and

movement (body English), will deter-

With the watercraft operating in

for-

mine the degree and sharpness of the

ward thrust, proceed as follows.

watercraft turn. Porpoising can be re-

duced or eliminated if the nozzle is

NOTE:

downward and speed is adjusted

Pressing the VTS trim button without

proportionately.

the engine in forward thrust will only

change the indication. The nozzle will

NOTE:

move to the selected VTS trim posi-

VTS position is indicated on a bar

tion when forward thrust is engaged.

gauge in the right lateral display of the

information center.

1. Press the VTS UP button once to

trim the bow of the watercraft up to

the next up trim position.

2. Press the VTS DOWN button once

iVTS

to trim the bow of the watercraft

down to the next down trim

position.

INFORMATION CENTER — VTS POSITION

INDICATOR

1. Bow up

2. Bow down

The VTS system allows for manually

adjusting the trim position of the

nozzle.

1. Bow up

2. Bow down

123

OPERATING INSTRUCTIONS

iVTS

INFORMATION CENTER — VTS POSITION

INDICATOR

1. Bow up

2. Bow down

NOTE:

If the VTS UP or DOWN button is

pressed and held, the pump nozzle

will keep moving until the button is re-

leased at the desired trim attitude or

the maximum trim position

(up or

down) is reached.

Using Preset Triim Positions

To select the mid trim position, it de-

Three preset trim positions can be

pends on the actual trim position.

selected.

Double-click on the VTS UP button if it

is positioned below mid trim or dou-

To select the highest trim position re-

ble-click on the VTS DOWN button if it

corded, double-click on the VTS UP

is positioned above mid trim.

button (bow up).

NOTE:

To select the lowest trim position re-

These preset trim positions are not

corded, double-click on the VTS

adjustable.

DOWN button (bow down).

124

OPERATING INSTRUCTIONS

Activating the Intelligent

Start engine when the message

Press start to go is displayed.

Debris Free Pump System

(iDF System) (if equipped)

When the sequence is completed,

The iDF system is designed to allow

the message Ready to start will

removing small debris or a cord

be displayed.

Start the engine and try the water-

caught in the jet pump by turning the

craft when the message Ready to

propeller in reverse during a few

start will be displayed.

seconds.

If the propulsion system has not

To activate the system, do the

returned to

100% of its original

following:

performance due to any remaining

debris, stop engine and perform

Stop the engine.

these steps again.

Press and hold the iDF button.

A moderate clog of weeds may re-

The following messages can ap-

quire multiple cycles before they

pear in the digital display during

can be entirely cleared out.

this step.

- Between cycles, it is more effi-

- Engagiing + R icon bliinkiing -

cient to try to drive the water-

The request is accepted and

craft to permit to it to plane in

the sequence begins.

order to help dislodge any re-

- Stop engine then hold iDF -

maining weeds before reat-

Engine is still running and must

tempting the iDF cycle.

be stopped before pressing the

iDF button again.

If the problem persists after sev-

- Hiigh exhaust temperature -

eral tries, try the On-Beach Water

Exhaust temperature is too

Cleaning procedure, refer to Jet

high and needs to cool down

pump Water Intake and Impeller

before activating the sequence.

Cleaning in Special Procedures

- Disable - The iDF system is not

section.

enabled on your watercraft,

see an authorized Sea-Doo

General Operating

dealer to enable it.

Recommendations

Start engine when the message

Press start to go is displayed.

NOTICE

Combustion engines need aiir to

When the sequence is completed,

operate; consequently thiis water-

the message Ready to start will

craft cannot be totallly watertiight.

be displayed.

Any maneuvers such as turning

Apply throttle when requested.

constantlly in tight ciirclles, plung-

If the message Impelller blocked

ing the bow through waves, or

is displayed - this indicates that the

capsiizing the watercraft, that

blocking is too important and the

cause the aiir inllet openings to be

system cannot turn the propeller in

under water may cause severe

the opposite direction. Have the

engine probllems due to water in-

watercraft servicing by an author-

gestiion. Refer to How to Steer the

ized Sea-Doo dealer.

Watercraft iin the Operatiing In-

After a few seconds, the engine

structions section and the War-

will shut down automatically. En-

ranty sectiion contaiined iin thiis

gaging

+ R icon bliinking will

Operator’’s Guiide.

appear.

125

OPERATING INSTRUCTIONS

Rough Water or Poor Viisibillity

distances under different conditions.

Operatiion

Stopping using the iBR system in a

straight line and in a turn should be

Avoid operation in these conditions. If

practiced extensively to become famil-

you must do so, proceed with caution

iar with the handling characteristics of

using minimum speed.

the watercraft under partial or full

braking conditions.

Crossing Wakes or Waves

1. The operator must grip the handle-

bar firmly and keep both feet on

WARNING

the footboards.

Allways practice braking in open

2. The passenger must grip the

waters ensuring there are no

handholds with both hands and

watercrafts or boats iin your imme-

keep both feet on the footboards.

diate viiciinity, especiiallly astern.

3. Reduce speed.

Other users of the waterways may

4. Always be prepared to steer and

not be able to maneuver or stop iin

maintain

your balance as

time to avoid you should you un-

necessary.

expectedly come to a fulll stop in

5. When going over waves, raise

front of them.

your body slightly off the seat to

absorb the shocks with your legs.

6. When crossing wakes, always

keep a safe distance from water-

craft ahead.

WARNING

It iis important to inform other op-

WARNING

erators who iintend to folllow iin a

When crossiing wakes or waves,

convoy formation of the braking

sllow down. Operator and passen-

and maneuveriing capabiiliity of

ger(s) should brace themsellves

your vehiicle and that a greater

and adopt a semii-standing posii-

distance should be maintained.

tiion to help absorb the bumps.Do

not jump wakes or waves - jjump-

The operator should also practice

ing can cause injjuriies such as

docking with an imaginary dock using

back or spinal injury (parallysiis).

the various controls available (iBR lev-

er and throttle lever).

Stopping/Dockiing

Release the throttle at a sufficient dis-

When the throttle is released, the

tance before the expected landing

watercraft is slowed by water drag

area.

against the hull. The stopping dis-

Reduce speed to idle.

tance will vary depending on the

watercraft size, weight, speed, water

Maneuver using a combination of the

surface condition, presence and direc-

iBR lever and throttle lever, shifting to

tion of wind and current.

neutral, reverse, or forward as

required.

The iBR system can also be used for

slowing down or for stopping more

Remember that when operating in re-

quickly, and for increasing maneuver-

verse, steering direction is reversed.

ability especially when docking.

Turning the handlebars to the left will

The operator should practice in open

waters at various speeds to become

familiarized

with

the stopping

126

OPERATING INSTRUCTIONS

move the stern to the right when back-

ing up, and vice-versa.

WARNING

Directiionall control iis reduced

when the throttlle is released and

lost when engiine iis off. Steeriing

direction is reversed when operat-

ing the watercraft in reverse.

Beachiing

NOTICE

It is not recommended to run the

watercraft to the beach.

Drive slowly towards the beach and

shut off the engine before the water is

less than 90 cm (3 ft) deep under the

lowest rear portion of the hull. Then

pull the watercraft to the beach.

NOTICE

Riding the watercraft iin shalllow

water may resullt iin damage to the

impelller, iBR components, or oth-

er jet pump components. Always

shut off the engiine before water iis

less than 90 cm (3 ft) deep and

never use reverse or braking.

127

OPERATING MODES

The icon ECO +OFF appears in the

Operating mode

FiishPro

display when this mode is selected.

availablle

Touring mode

Sport Mode

SPORT MODE provides for instant

Sport mode

throttle response and more rapid ac-

celerations than DEFAULT riding

ECO mode

MODE.

Speed limiter

Once activated, SPORT MODE will

mode

remain active until it is deactivated by

the operator, or the engine is shut

Slow speed

down whereby it defaults back to DE-

mode (Trolling

FAULT riding MODE.

mode)

Ski mode

Actiivating Sport Mode

To activate the Sport mode, press

Learning key

once on the MODE button while in

mode

DEFAULT riding mode. The sport icon

will start to flash and a safety mes-

X = Indicates a standard feature

sage will scroll. For safety reason, fol-

- = See a Sea-Doo dealer for

low the instruction in the safety

availability.

message to activate the sport mode.

Once activated, the SPORT icon will

To change the operating mode;

turn ON.

1. Press MODE button,

Deactiivating Sport Mode

2. Acknowledge the safety message

by pressing and holding MODE

A single press on MODE button will

button will get the SPORT mode,

take you to the ECO mode.

3. Pressing MODE button again will

activate the ECO mode.

ECO Mode

(Fuel Economy Mode)

ECO mode provides a smoother throt-

tle application and increased fuel

economy.

Speed Control Modes

To enter one of the speed control

modes, press SPEED CTRL button.

Depending of the speed of the water-

craft, only one of the following modes

TYPICAL

will be activated.

Once the desired mode is activated,

Touring Mode

press the SPEED CTRL button then

By default, the watercraft is set to this

change the value with the UP or

riding mode of operation when

DOWN arrow button while the SET

started.

LEVEL message is active.

It is also called Normal riding mode.

128

OPERATING MODES

To exit the selected speed control

Activating Speed Liimiter Mode

mode, press MODE button or long

1. Maintain a constant speed.

press SPEED CTRL button.

2. Press the Speed Control button on

the left keypad.

Speed Liimiter Mode

Speed limiter mode is a function of

iTC (intelligent Throttle Control) sys-

tem that allows the operator to set the

desired maximum watercraft speed.

This is useful when cruising for long

distances, operating in limited speed

zones, or towing a tuber, skier or wake

boarder.

The operator must keep the throttle

TYPICAL

depressed to maintain forward speed.

You will hear a beep indicating that

Once the maximum speed is set, the

you are now in speed limiter mode,

operator can vary the watercraft

and a speed limiter MODE indicator

speed from idle speed up to the set

will be lit.

speed using the throttle lever. The set

speed will not be exceeded even if the

throttle lever is fully depressed.

iVTS

As you proceed under a constant

speed setting, keep your attention lev-

el up to maintain good situational

awareness.

TYPICAL

Slowing down is a matter of releasing

the throttle lever further than the set

1. Speed

limiter/Slow

Speed MODE

point, or by pulling the iBR lever in.

INDICATOR

If the iBR lever is pulled in for braking,

Speed Limiter mode is overridden but

NOTE:

not deactivated.

Activating speed limiter mode of oper-

ation only limits the maximum speed

Once the iBR lever is released and

available when depressing the throttle

the throttle is pulled in to engage for-

lever. The throttle lever must be held

ward thrust, the speed limiter function

in to maintain forward speed. Water-

will reengage to limit the watercraft

craft speed can be varied from idle up

speed as it was set before.

to the set cruise speed using the throt-

tle lever once the speed limiter func-

Prerequiisite for Speed Limiiter

tion is activated. Watercraft speed

Mode Actiivation

may vary depending on water condi-

Speed limiter MODE can be activated

tions during use.

when the watercraft is going at more

then 15 km/h (9 mi/h).

Deactivatiing Speed Limiter Mode

To deactivate speed limiter mode:

NOTE:

Speed limiter mode is not available if

1. Release the throttle lever.

slow speed mode is engaged.

2. Press and hold the speed limiter

button.

129

OPERATING MODES

Deactivation of speed limiter mode is

Actiivating Sllow Speed Mode

indicated by:

To activate slow speed mode of

- The speed limiter indicator will go

operation:

off.

1. Release the throttle lever to idle

RPM.

NOTE:

2. Press the Speed Control button on

If the throttle lever is not fully released

the left keypad.

when the button is pressed to deacti-

vate the speed limiter mode, the

speed limiter MODE indicator will re-

main on. The speed limiting function

will stay active until the throttle is fully

released, then the speed limiter

MODE indicator will go out.

Slow Speed Mode

The Intelligent Throttle Control also al-

lows for a Slow Speed Mode where

the driver can adjust and set idle

TYPICAL

speed. This is useful when operating

in slow speed zones where the driver

The Speed limiter/Slow Speed indica-

must be especially attentive to possi-

tor will come on in the multifunction

ble obstacle avoidance.

display to indicate activation.

If you accelerate above approximately

14 km/h (9 mi/h) , Slow Speed Mode

will be deactivated and the engine will

iVTS

return to idle RPM when the throttle is

released.

Should a situation arise where the op-

erator must stop or accelerate quickly

TYPICAL

away from a hazardous situation, pull-

1. Speed

limiter/Slow

Speed MODE

ing in the iBR lever, or pulling in on the

INDICATOR

throttle lever will deactivate slow

speed mode and normal control of the

A message will scroll in the multifunc-

watercraft will be returned to the

tion display to specify that you are

operator.

now in slow speed mode.

Prerequisite for Slow Speed Mode

The default slow speed setting of 5 will

Activation

show in the numerical display.

Slow Speed MODE can be activated

when the watercraft is going at less

then 15 km/h (9 mi/h).

IVTS

NOTE:

Speed limiter mode is not available if

slow speed mode is engaged.

130

OPERATING MODES

Changing Set Slow Speed

throttle lever, the iBR gate stays in the

forward position.

To iincrease or decrease the set slow

speed, press the UP/DOWN button on

When using the iBR lever, the iBR

the RH handlebar once, or repeatedly.

gate will move towards the reverse

position, then neutral when the lever

NOTE:

is released.

There are 9 slow speed settings avail-

able (1 through 9). Adjust slow speed

SLOW SPEED MODE deactivation

mode to desired speed.

will be indicated in the following

manner:

When pressing the up/down button, a

The Speed Limiter indicator will go

message ''SET LEVEL'' will appear.

out

You can select from one of the 9 slow

speed setting (1 to 9).

Level 5 is the default and it corre-

spond to the normal idle of the vehicle.

By using level 1-4 you can slow down

the vehicle and go as slow as 1.5 km/

h (1 mi/h). The slow speed mode can

be used as a trolling mode and is use-

ful for fishing. Level 6-9 gives you the

ability to go up to 12 km/h (7 mi/h)

without touching the throttle lever.

WARNING

The operator must always be

seated in driviing posiition at alll

times when watercraft is at speed.

- The tether cord must be at-

tached to the operator’’s PFD or

wrist (wriist strap required) at alll

times.

NOTE:

Speed will vary depending on load,

wind and waves conditions

Deactiivatiing Slow Speed Mode

The slow speed mode can be deacti-

vated using any of the following

methods:

- Pressing and holding the Speed

Control button.

- Depressing the iBR lever.

- Accelerating past the set slow

speed.

When deactivating SLOW SPEED

MODE by accelerating using the

131

SPECIAL PROCEDURES

Jet Pump Water Intake and

Modells equiipped wiith the iDF

system

Impeller Cleaning

If the watercraft is equipped with the

WARNING

iDF system, use it now. Refer to How

Keep away from intake grate

to Use the intelligent Debris Free

whille engiine iis running. Items

Pump System in Operating Instruc-

such as llong hair, loose cllothing

tions section.

or personall fllotation deviice straps

Modells without iiDF system

can become entangled in moving

parts.

1. Rock the watercraft several times.

Most of the time, this will remove

Weeds, shells or debris can get

the blockage.

caught on the intake grate, drive shaft

2. Start engine and make sure water-

and/or impeller. A clogged water in-

craft operates properly.

take may cause troubles such as:

If the aforementioned method does

- Cavitatiion: Engine speed is high

not work:

but watercraft moves slowly due to

3. With engine running and before

reduced jet thrust, jet pump com-

applying throttle, pull the iBR lever

ponents may be damaged.

in to select reverse operation.

- Overheatiing: Since the jet pump

4. Vary throttle quickly several times.

operation controls the flow of water

5. Repeat procedure if necessary.

to cool the exhaust system, a

clogged intake will cause the en-

If system is still blocked, move the

gine to overheat and damage en-

watercraft out of the water for

gine internal components.

cleaning. Refer to On-Beach

Water Cleaning.

A weed clogged area can be cleaned

as follows:

On-Beach Water Clleaniing

WARNING

If it iis necessary to reach iin to re-

The tether cord MUST BE RE-

move any foreign objject caught in

MOVED from the engine cut-off

the propullsiion system, the tether

swiitch to prevent acciidental en-

cord MUST BE REMOVED from

gine starting before cleaniing the

the engiine cut-off swiitch.

jet pump area.

In-Water Clleaniing

1. Place a cardboard or a carpet be-

side the watercraft to prevent

NOTICE

scratching when turning the water-

Ensure there iis at least 90 cm (3

craft for cleaning.

ft) of water under the llowest rear

2. Rotate the watercraft to any side

portion of the hulll when all pas-

for cleaning.

sengers are aboard prior to start-

ing the engiine. Otherwiise damage

to the propulsion system compo-

nents may occur.

132

SPECIAL PROCEDURES

NOTICE

An objject or tooll caught iin the iiBR

system when using the iiBR over-

riide functiion may cause damage

to the iiBR components. Remove

alll riigid foreiign objjects that may

obstruct the iiBR gate travel before

moviing iit.

WARNING

TYPICAL

If it iis necessary to reach iin to re-

3. If equipped, move the iBR to the

move any foreign objject caught in

forward position. Refer to iBR

the propulsiion system, striictlly ob-

Override Function for detailed

serve the folllowing before

instructions.

proceediing:

4. Clean the water intake area.

– Remove tether cord from the

engiine cut-off swiitch.

If the system is still clogged, refer

– Waiit at lleast 5 minutes.

to an authorized Sea-Doo dealer

– Do not press on START/STOP

for servicing.

button. Should the START /

STOP button be pressed, wait

NOTICE

another 5 minutes.

Inspect water iintake grate for

damage. Refer to an authoriized

Activating iBR Override Function

Sea-Doo dealer for repaiir as

1. Power up the electrical system by

necessary.

pressing the START/STOP button.

2. Install the tether cord on the en-

iBR Override Function

gine cut-off switch.

When the iBR override function is acti-

NOTE: The tether cord must be in-

vated, it allows the user to electrically

stalled to ensure the information cen-

move the iBR gate and nozzle through

ter will not shut off all indications after

its full range of motion using the VTS

its self test function. Electrical power

control button.

will stay on for approximately 1 hour.

NOTE:

3. Pull in and hold the iBR lever for

The iBR override function is only avail-

the entire procedure.

able when the engine is not running.

WARNING

When moving the iiBR gate using

the iiBR overriide functiion, ensure

no one iis near the rear of the

watercraft. Movement of the gate

may squeeze fingers.

133

SPECIAL PROCEDURES

Capsized Watercraft

The watercraft is designed so that it

should not turn over easily. Two spon-

sons mounted on the side of the hull

assist watercraft stability. If it turns

over, it will remain capsized.

To turn the watercraft upright, ensure

the engine is off and the D.E.S.S. key

is NOT on its post, then grab the inlet

grate, step on a side bumper rail and

use your weight to rotate the water-

iBR lever pulled and held

craft towards you.

When the IBR OVERRIDE

NOTE:

PRESS MODE BUTTON mes-

A label on the stern near the flushing

sage appears in the multifunction

connector provides instructions on

gauge, press the MODE button.

how to turn the watercraft right side

up. The label is upside down so that it

When the function is activated, a

can be read when the watercraft is

ON message will be shown.

overturned.

While still holding the iBR lever in,

press the VTS UP/DOWN button

to move the iBR gate to the de-

sired position. Ensure the VTS in-

dication in the multifunction gauge

changes with the iBR gate move-

ment. If the iBR gate moves up-

wards, the indication moves

upwards.

Release the iBR lever.

Remove the tether cord from the

engine cut-off switch.

WARNING

TYPICAL

If it iis necessary to reach iin to re-

The engine features a Tip-Over Pro-

move any foreign objject caught in

tection System (T. O. P. S.™). When

the propullsiion system, striictlly ob-

the watercraft tips over, the engine is

serve the folllowing before

automatically stopped.

proceediing:

– Remove tether cord from the

When the watercraft is returned to its

engiine cut-off swiitch.

normal operating position, the engine

– Waiit at lleast 5 minutes.

can be started normally.

– Do not press on START/STOP

button. Should the START /

STOP button be pressed, wait

another 5 minutes.

134

SPECIAL PROCEDURES

Water-Flooded Engine

NOTICE

When the watercraft has been

NOTICE

turned over 5 miinutes, do not at-

Never try to crank or start the en-

tempt to crank the engine to avoid

giine. Water trapped in iintake

water iingestiion that would dam-

maniifolld would flow towards the

age the engiine. See an author-

engine and possiibly cause severe

ized Sea-Doo dealer as soon as

engine damage.

possiblle.

Bring the watercraft to an authorized

NOTICE

Sea-Doo dealer as soon as possible

If the engiine does not crank, do

to have it serviced.

not attempt to start it anymore.

Otherwise, the engiine could be

NOTICE

damaged. See an authoriized

Faiilure to have the engine prop-

Sea-Doo dealer as soon as

erlly serviced may cause severe

possiblle.

engine damage.

As soon as possible, check for pres-

Towing the Watercraft in

ence of water in the bilge. Drain as

Water

necessary when back to the shore.

Special precautions should be taken

Submerged Watercraft

when towing a Sea-Doo watercraft in

water.

To limit damages to the engine, per-

form the following procedure as soon

The maximum recommended towing

as possible.

speed is 8 km/h (5 MPH).

1. Drain bilge.

This will prevent the exhaust system

2. If it was submerged in salt water,

from filling with water, which may lead

spray bilge and all components

to water being injected into and filling

with fresh water using a garden

the engine. Without the engine run-

hose to stop the salt corroding

ning, there isn't any exhaust pressure

effect.

to push the water out the exhaust

outlet.

NOTICE

Never try to crank or start the en-

gine. Water trapped in intake

NOTICE

manifold woulld fllow towards the

Faiilure to folllow these instructiions

engiine and possiiblly cause severe

may resullt in damage to the en-

engiine damage.

giine. If you must tow a stranded

watercraft iin water, be sure not to

exceed the maxiimum towing

3. Bring the watercraft to an author-

speed of 8 km/h (5 MPH).

ized Sea-Doo dealer as soon as

possible to have it serviced.

NOTICE

Faiilure to have the engiine prop-

erly serviiced may cause severe

engiine damage.

135

MAINTENANCE SCHEDULE

Maintenance is very important to keep your watercraft in safe operating condi-

tion. The vehicle should be serviced as per the maintenance schedule.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

Perform periodic checks and follow the maintenance schedule. The maiinte-

nance schedule does not exempt the pre-ride inspection.

WARNING

Faiilure to properly maiintain the watercraft accordiing to the maiintenance

schedulle and procedures can make it unsafe to operate.

EPA Regulation - Canadian and USA Watercrafts

A repair shop or person of the owner''s choosing may maiintaiin, replace, or

repair emission control devices and systems. These instructions do not require

components or service by BRP or authorized Sea-Doo dealers.

Although an authorized Sea-Doo dealer has an in-depth technical knowledge

and tools to service your vehicle, the emission-related warranty is not conditioned

on the use of an authorized Sea-Doo dealer or any other establishment with

which BRP has a commercial relationship.

Proper maintenance is the owner’s responsibility. A warranty claim may be de-

nied if, among other things, the owner or operator caused the problem through

improper maintenance or use.

For emission-related warranty claims, BRP is limiting the diagnosis and repair of

emission-related parts to the authorized Sea-Doo dealers. For more information,

please refer to the US EPA Emissions Warranty contained in the warranty

section.

You must follow the instructions for fuel requirements in the fueling section of this

manual. Even if gasoline containing greater than ten volume percent ethanol is

readily available, the US EPA issued a prohibition against the use of gasoline

containing greater than 10 vol% ethanol that applies to this vehicle. The use of

gasoline containing greater than 10 vol% ethanol with this engine may harm the

emission control system.

138

MAINTENANCE SCHEDULE

Salt Water/ Dirty Water Usage

Whenever your watercraft is used in salt or dirty water, this type of usage re-

quires maintenance tasks to be performed between the regular yearly intervals.

These are identified as A+ in the chart below.

If you regularly ride in sallt or diirty water, follow the A+ interval and perform the

tasks outlined in the chart below.

Maintenance Schedule

Make sure to perform proper maintenance at recommended intervals as indi-

cated in the tables.

The maintenance chart indicates the items needing to be addressed based on 2

criteria, whichever happens first:

- Calendar time

- Watercraft hours.

Your driving habits determines the factors you shall adhere to. For example:

- Someone who uses their watercraft every weekend would follow the hours

reading to determine the frequency of his maintenance.

- Someone who uses their watercraft seldomly over the year or only on a few

occasions would follow the calendar tiime to determine the frequency of his

maintenance.

IMPORTANT: The following tables show the appropriate maintenance appli-

cation for the first

3 years. For subsequent years, repeat the same pattern

alternatively.

Maintenance Overview

Regular/ Salt/ Dirty

Calendar Time

Hour meter

water

Every Month

A+

1 Year

100 Hours

Every Month

A+

2 Years

200 Hours

A and B

Every Month

A+

3 Years

300 Hours

139

MAINTENANCE SCHEDULE

Rotax 1630 ACE Engiines

Regullar

A=Adjust

C=Clean

F=Flush

Every year

Every 2 years

I=Inspect

L=Lubricate

100 Hours

200

Hours

R=Replace

T=Torque

Air and Fuel Delivery

Air delivery components and function (ducts,

I, C

hoses, clamps)

Fuel components and function (Fuel tank cap,

fuel tank fixation, hose condition, leaks)

Supercharger

Deck and Hull

Sacrificial anode(s)

Body panels and hardware

I, T

Hull

Engine and Cooling

Engine cooling components (coolant

concentration, coolant level, hose condition,

I, A

clamps, leaks)

Engine oil and oil filter

Ignition components and function

Engine rubber mounts

Spark plugs

Engine coolant

Every 5 years

or 300 hour

Exhaust and Emissions

Exhaust components (gaskets, pipes, muffler

condition, leaks)

Exhaust

iBR

iBR components and function

Propulsion

Propulsion components and function

I, L

Electrical

Battery connections and condition

140

MAINTENANCE SCHEDULE

SALT/ DIRTY

A+

WATER

After each

ride in salt

A=Adjust

C=Clean

dirty water

Every 2

F=Flush

Every year

years

I=Inspect

monthly

L=Lubricate

100 Hours

when used in

200 Hours

R=Replace

salt

T=Torque

dirty water

Air and Fuel Delivery

Air delivery components and

I, C

function (ducts, hoses, clamps)

Fuel components and function (Fuel

tank cap, fuel tank fixation, hose

condition, leaks)

Supercharger

Deck and Hull

Sacrificial anode(s)

Every month

Body panels and hardware

I, T

Hull

Engine and Cooling

Engine compartment

After each

ride

Engine compartment metallic

components

Each month

Engine cooling components (coolant

concentration, coolant level, hose

I, A

condition, clamps, leaks)

Engine oil and oil filter

Ignition components and function

Engine rubber mounts

Spark plugs

Engine coolant

Every 5 years

or 300 hour

Exhaust and Emissions

Exhaust components (gaskets,

pipes, muffler condition, leaks)

142

MAINTENANCE SCHEDULE

SALT/ DIRTY

A+

WATER

After each

ride in salt

A=Adjust

C=Clean

dirty water

Every 2

F=Flush

Every year

years

I=Inspect

monthly

L=Lubricate

100 Hours

when used in

200 Hours

R=Replace

salt

T=Torque

dirty water

Exhaust

After each

ride

iBR

iBR components and function

Propulsion

Propulsion components and function

Electrical

Battery connections and condition

Electrical harness routing

Modules and applicable software

updates

Operation of control switches and

lighting

Steering and Controls

Steering components and function

Throttle operation

Steering and Controls

Steering components and function

Throttle operation

Feature

Fish finder transducer support

I, A

143

MAINTENANCE PROCEDURES

This section includes instructions for

basic maintenance procedures.

WARNING

Turn off the engiine and folllow

these maiintenance procedures

when performing maintenance. If

you do not folllow proper maiinte-

nance procedures you can be in-

jured by hot parts, moving parts,

ellectriciity, chemiicalls or other

hazards.

WARNING

Shoulld removal of a lockiing de-

TYPICAL

viice (e.g. llock tabs, sellf-llockiing

3. Remove the screws.

fasteners, etc.) be requiired, al-

ways replace wiith a new one.

NOTICE

Never lleave any objject, rag, tooll,

etc., iin the engiine compartment or

in the biilge.

Engine Service Cover

TYPICAL

4. Remove the cover.

Installliing the Engine Service Cover

1. The installation is the reverse of

the removal procedure. However,

pay attention to the following.

2. Install all screws.

3. Tighten screws to specification.

Tighteniing Torque

Removiing the Engine Service

Cover

Engine service

2.8 ± 0.2 Nm

cover screw

(25 ± 2 lbf-in)

1. Remove the seats.

2. Remove the ski/ wake pylon cover.

144

MAINTENANCE PROCEDURES

Engine Oil

Recommended Engine Oill

Rotax^® engines were developed and validated using the XPS^® oil.

BRP recommends the use of its XPS engine oil or an equivalent at all time.

Damage caused by the use of an oil not suitable for the engine may not be cov-

ered by the BRP Limited Warranty.

XPS Recommended Engine Oil

General purpose

5W40 synthetic blend oil

Warm temperature

10W50 synthetic oil

If the recommended XPS engine oil is not available:

Use a 4-stroke SAE synthetiic

engine oill meeting or exceeding the

following lubricant industry

specifications.

Always check the API service label

Engine Without Supercharger

certification on the oil container, it

must contain at least one of the

indicated standards.

API serviice classiificatiion SN or

JASO-MA2

Use a 4-stroke SAE motorcyclle

engine oill compatiblle wiith wet

cllutches meeting or exceeding the

following lubricant industry

specifications.

Engine Wiith Supercharger

Always check the API service label

certification on the oil container, it

must contain at least one of the

indicated standards.

API serviice classiificatiion SN or

JASO-MA2

Verifying the Engiine Oiil Levell

CAUTION

NOTICE

Many components in the engiine

compartment may be very hot. Dii-

Operating the engine with an im-

rect contact may result iin skin

proper llevell may severelly dam-

burn.

age engine.

145

MAINTENANCE PROCEDURES

If Watercraft is Out of the Water

NOTICE

Watercraft must be levell.

CAUTION

When operating the engine whiile

the watercraft is out of water, the

heat exchanger in the ride plate

may become very hot. Avoiid any

contact wiith the ride plate as

TYPICAL

burns may occur.

1. Oil dipstick

2. Oil filler cap

1. Raise trailer tow pole, then block in

position when bumper rail is level.

11. Reinstall

dipstick,

push in

2. Install a garden hose on the ex-

completely.

haust system flushing connector.

12. Remove dipstick again and read

Refer to Exhaust System in this

oil level. It should be between the

section and follow the procedure.

FULL and ADD marks.

NOTICE

Never run engine wiithout supply-

ing water to the exhaust system.

Faiilure to cool exhaust system

may severely damage iit.Never run

TYPICAL

engine llonger than 2 miinutes.

1. Full

Driive lline seall has no cooliing

2. Add

when watercraft is out of water.

3. Operating range

3. Remove the seat(s).

13. Add oil to ensure the level is be-

4. Start the engine.

tween marks as required.

5. Open the water tap.

1. Remove oil cap.

6. Run the COLD engine at iidle for

30 seconds.

2. Place a funnel in valve cover

7. Close water tap.

opening.

8. Bring engine RPM to 4000-4500

3. Add a small amount of the rec-

RPM for 15 seconds.

ommended oil to reach the

9. Stop the engine abruptly by press-

proper level.

ing the start/stop button or remov-

ing the tether cord.

NOTICE

10. Wait at least 30 seconds for the oil

Do not overfilll.

to settle in the engine, then pull

dipstick out and wipe clean.

146

MAINTENANCE PROCEDURES

Engine Coolant

Recommended Engiine Coolant

XPS Recommended Coollant

Extended life pre-mixed coolant

If the Recommended XPS Coolant

is Not Available

Use a low silicate, extended life

TYPICAL

ethylene-glycol premixed coolant

1. Oil dipstick

(50%-50%) specifically formulated

2. Oil filler cap

for internal combustion aluminum

engines.

NOTE:

NOTICE

Every time oil is added in the engine,

the complete procedure explained in

Always use ethyllene-gllycol anti-

this section must be carried out again.

freeze contaiiniing corrosion inhibii-

Otherwise, you will obtain a false oil

tors specificallly for iinternal

level reading.

combustiion alumiinum engiines.

14. Properly reinstall oil cap and

To prevent antifreeze deterioration, al-

dipstick.

ways use the same brand and grade.

Never mix different brands or grades

NOTICE

unless cooling system is completely

Ensure that oiil fiilller cap is tighten

flushed and refilled.

properlly. Otherwiise engiine oiil can

spill out.

Engiine Coollant Levell

WARNING

Engine Oill Change and Oill Fiilter

Replacement

Check coollant llevel wiith engine

cold. Never add coolant when en-

The oil change and filter replacement

giine iis hot.

may be performed by an authorized

Sea-Doo dealer, repair shop, or per-

son of your own choosing.

CAUTION

Many components in the engiine

compartment may be very hot. Dii-

rect contact may result iin skin

burn.

1. Remove seats.

2. Locate the expansion tank cap.

147

MAINTENANCE PROCEDURES

Engine Coolant Replacement

Coolant replacement should be per-

formed by an authorized Sea-Doo

dealer.

Ignition Coils

Ignitiion Coill Access

1. Remove tether cord from the en-

gine cut-off switch.

2. Remove seat(s).

TYPICAL

3. Remove engine service cover by

removing the retaining screws.

With watercraft on a level surface,

coolant level should be between

MIN. and MAX. marks on coolant

reservoir when engine is cold.

COOLANT EXPANSION TANK

1. Level between marks when engine is cold

Removing the Igniition Coiil

1. Disconnect ignition coil connector.

NOTE:

NOTICE

The watercraft is level when it is in

water. When on a trailer, raise trailer

Do not pry on igniitiion coill usiing

tow pole and block in this position

any tool.

when the lower part of the hull is level.

2. Remove ignition coil retaining

Add coolant, see Recommended

screw.

Engine Coolant for specification, to

3. Remove ignition coil from spark

adjust coolant level between

plug by rotating coil side to side as

marks as required. Use a funnel to

you pull up.

avoid spillage. Do not overfill.

3. Properly tighten the expansion

Installliing the Igniitiion Coill

tank cap. Reinstall seats.

1. Align the retaining screw hole of

NOTE:

the ignition coil with the threaded

A cooling system that frequently re-

hole on the valve cover.

quires coolant is an indication of leaks

2. Install the ignition coil on the spark

or engine problems. See an author-

plug and push it all the way down

ized Sea-Doo dealer.

until it rests on the valve cover.

148

MAINTENANCE PROCEDURES

3. Install the retaining screw and

NOTICE

tighten to specification below.

Do not adjust gap on thiis type of

Tiightening Torque

spark pllug. The adjustment coulld

weaken negative electrodes

Ignition coil

which may lead to electrode

9 ± 1 Nm

retaining

breaking and severe engiine

(80 ± 9 lbf-in)

screw

damage.

4. Connect ignition coil connector.

2. Apply anti-seize lubricant on the

spark plug threads to prevent pos-

Spark Plugs

sible seizure.

3. Hand screw spark plug into cylin-

Removing the Spark Pllug

der head. Then, tighten the spark

Remove the ignition coils. Refer to

plug to specification with a spark

Removing the Ignition Coil.

plug socket.

Clean the spark plug and cylinder

head with compressed air.

Tightening Torque

Unscrew the spark plug completely

using a spark plug socket.

18 ± 2 Nm

Spark plug

(159 ± 18 lbf-in)

4. Install the ignition coils. Refer to

Ignition Coil.

Exhaust System

DANGER

DO NOT run the engiine iindoors or

wiithout adequate ventillatiion or

permiit exhaust fumes to accumu-

late iin confined areas. Engiine ex-

Approved socket

haust contaiins carbon monoxiide

Improper socket

(CO) whiich, iif iinhalled, can cause

serious braiin damage or death.

Use the ignition coil to take spark

plug out of its hole.

Fllushiing the Exhaust System

Installliing the Spark Plug

Flushing the exhaust system with

Prior to installation, ensure the contact

fresh water is essential to neutralize

surfaces of the cylinder head and

corroding effects of salt or other

spark plug are free of grime.

chemical products present in water. It

will help to remove sand, salt, shells

1. Using a wire feeler gauge, check

or other particles in water jackets and/

electrode gap as specified in Tech-

or hoses.

nical Specifications. Replace the

spark plug if not to specification.

Exhaust system flushing should be

performed when the watercraft is not

expected to be used further the same

day or when the watercraft is stored

for any extended time.

149

MAINTENANCE PROCEDURES

NOTICE

Recommended Tooll

Faiilure to fllush the system, when

Flushing connector

necessary, willl severelly damage

adapter

exhaust system. Make sure en-

295 500 473

giine operates during entire

procedure.

WARNING

Perform these operatiions in a welll

ventiilated area. Certain compo-

nents iin the engiine compartment

may be very hot. Direct contact

1. Quick connect adapter

may resullt in skiin burn. Do not

2. Flushing connector adapter

touch any ellectriicall part or jet

pump area when engiine iis

2. Start the engine then immediately

running.

open the water tap.

NOTICE

WARNING

Allways start the engiine before

When operating the engine whiile

openiing the water tap. Open

the watercraft is out of the water,

water tap iimmediatelly after en-

the heat exchanger iin the riide

gine is started to prevent over-

pllate may become very hot. Avoiid

heating. Never run engine without

any contact with ride plate as

supplyiing water to the exhaust

burns may occur.

system when watercraft is out of

water.

1. Connect a garden hose to connec-

tor located at the rear of watercraft.

3. Run the engine 90 seconds at idle.

Do not open water tap yet.

NOTICE

Never run engine llonger than 2

minutes. Drive liine seal has no

coolling when watercraft is out of

water.

4. Ensure water flows out of jet pump

while flushing.

5. Close the water tap, run the engine

at 5000 RPM for 5 seconds and

then stop the engine.

1. Water inlet connector

NOTICE

Allways cllose the water tap before

NOTE:

stopping the engine.

The following tool is recommended

when a quick connect adapter is used

to ease garden hose installation.

150

MAINTENANCE PROCEDURES

6. Disconnect the garden hose and

the flushing connector adapter (if

used).

Ride Plate and Water Intake

Grate

Inspecting the Riide Plate and the

Water Intake Grate

Inspect ride plate and jet pump water

intake grate for damage. Visit your

1. Sacrificial anodes

Sea-Doo dealer to have any damaged

part repaired or replaced.

Check sacrificial anodes for wear. If

worn more than half, replace them.

WARNING

The tether cord must allways be

Removiing the Sacrificiall Anode

removed from the engine cut-off

Unscrew sacrificial anode retaining

swiitch prior to inspecting the iin-

nut and remove anode.

take grate.

Installling the Sacriifiicial Anode

Installation is the reverse of the re-

moval procedure.

Tiightening Torque

9 ± 1 Nm (80 ± 9 lbf-in)

Fuses

INSPECT THESE AREAS

Fuse Locatiion

1. Water intake

Most fuses are located inside a single

2. Ride plate

fuse box.

Sacrificial Anodes

To access the fuse box:

Remove seat(s).

Inspecting the Sacriificial Anodes

Sacrificial anodes are located on:

- Pump

– Ride plate.

151

MAINTENANCE PROCEDURES

To remove fuse from holder, pull fuse

out. Check if filament is melted.

1. Fuse box

2. Main fuse

To remove a fuse box cover, squeeze

locking tabs together, hold and pull

TYPICAL

fuse box cover to open.

1. Fuse

NOTE:

2. Check if melted

Fuse ratings and positions are illus-

3. Ampere rating

trated on the fuse box cover.

WARNING

Use the fuse remover/installer in-

cluded in the fuse box to ease fuse

If fuse burns out repeatedlly,

removal.

source of mallfunctiion should be

determiined and corrected before

A single fuse is located at the front of

restarting. Visit an authorized

the vehicle. See a Sea-Doo dealer for

Sea-Doo dealer for servicing.

more details.

Fuse Description

Single Fuse at Front

Sonar

Fuse

Rating

Descriiptiion

Not used

Fuel Inj., Ing.

1. Sonar fuse

15 A

Coils and Fuel

Pump

Inspectiing a Fuse

Bilge Pump (if

Check fuse condition and replace it if

equipped)

necessary.

Not used

WARNING

Not used

Never use a hiigher rated fuse

than specified.

30 A

Charge

152

WATERCRAFT CARE

Remove the watercraft from the water

Many marks, as shoes marks, can be

every day.

removed easily with this method.

Post-Operation Care

Body and Hull

Fllushiing the Exhaust System

Repair

The exhaust system should be

If any repairs are needed to body

flushed daily when watercraft is used

components or to the hull, contact

in salt or foul water.

your authorized Sea-Doo dealer.

Refer to Maintenance Procedures.

Clleaniing

Wash the body and the hull with a

Addiitiionall Care for Foul Water or

soap and water solution (use only mild

Sallt Water Operation

detergent). Rinse thoroughly with

When the watercraft is operated in

fresh water.

foul water and particularly in salt

water, additional care should be taken

Remove marine organisms from the

to protect the watercraft and its

inside and outside of the hull.

components.

NOTICE

Rinse watercraft bilge area with fresh

Never clean using the followiing

water.

products:

Never use a high pressure washer to

– XPS S4 Heavy Duty Cleaner

clean the bilge. USE LOW PRES-

– Strong detergent

SURE ONLY (such as a garden

– Degreasing agent

hose).

– Ammonia

– Acetone or other ketones

High pressure can cause damages to

– Alcoholl

electrical or mechanical systems.

– Tolluene or other aromatiic

solvents

CAUTION

– Chlorinated solvents

Alllow engine to cool before per-

– Miinerall spiirits

formiing any maintenance.

– Paiint thinners

– Petroleum based products.

NOTICE

Stains may be removed from the seat

Faiilure to perform proper care

and fiberglass using the XPS All Pur-

such as: watercraft rinsing, ex-

pose Cleaner and Degreaser or the

haust system flushing and anti-

equivalent.

corrosiion treatment, when

watercraft iis used in salt water,

To clean the carpets, use 3M™ Citrus

wiilll result iin damage to the water-

Base Cleaner (24 oz spray can) or an

craft and its components. Never

equivalent.

leave the watercraft stored iin dii-

rect sunlight.

WARNING

Never applly pllastic or vinyl pro-

Seat Cleaning

tector on the carpets or seat as

the surface wiilll become sliippery

Before applying a cleaning product on

and the occupants may sliip off the

the seat, try removing marks with a

watercraft.

white eraser.

154

STORAGE AND PRESEASON PREPARATION

Storage

Inspecting the Jet Pump

Visit your authorized Sea-Doo dealer.

WARNING

Fuell System

Because fuel and oill are flamma-

blle, you should have an author-

Protecting the Fuel System

ized Sea-Doo dealer, repaiir shop,

or person of your own choosiing to

A fuel stabilizer should be added in

inspect the fuell system integriity

the fuel tank to prevent fuel deteriora-

as specifiied iin the periodic iin-

tion and fuel system gumming. Follow

spectiion chart.

stabilizer manufacturers' instructions

for proper use.

It is recommended that the watercraft

Service Product

be serviced by an authorized Sea-Doo

dealer, repair shop, or person of your

Fuel stabilizer

own choosing for storage, however

the following operations can be per-

formed by you with a minimum of

NOTICE

tools.

Fuel stabiiliizer shoulld be added

prior to engiine llubriication to pre-

NOTE:

vent the lloss of the chemiicall prop-

Carry out the following tasks in the

ertiies of fuell and protect the fuel

same order as detailed in this section.

system against varniish deposits.

NOTICE

Fill up fuel tank completely. Make sure

Do not run the engine during the

there is no water inside fuel tank.

storage period.

NOTICE

Propulsiion System

Should any water be trapped in-

side fuel tank, severe iinternal

Cleaning the Jet Pump

damage may occur to the fuell in-

jection system.

WARNING

Always remove tether cord from

Engine and Exhaust

the engiine cut-off swiitch to pre-

vent unexpected engine starting

Flushing the Exhaust System

before clleaniing the jet pump area.

Perform procedure as described in

Engiine must not be runniing for

Maintenance Procedures section.

this operatiion.

Replacing the Engiine Oiil and Oill

Fillter

Rinse the jet pump by spraying water

through its inlet and outlet openings.

The oil change and filter replacement

may be performed by an authorized

Spray an anti-corrosive product on the

Sea-Doo dealer, repair shop, or per-

propulsion system parts.

son of your own choosing.

Service Product

Draiiniing the Exhaust System

In areas where temperature may

XPS Anti-Corrosive Lubricant or

freeze, water trapped in the exhaust

equivalent

system and intercooler must be

removed.

156

STORAGE AND PRESEASON PREPARATION

Using the flushing connector, inject

prevent fuel from being injected

pressurized air at 379 kPa (55 lbf/in²)

and disable the ignition during en-

into system until there is no more

gine cranking.

water flowing from jet pump.

4. Press the START/STOP button to

crank the engine a few turns. This

will distribute the oil on the cylinder

walls.

5. Apply anti-seize lubricant on spark

plug threads, then reinstall them in

the engine. Refer to Maintenance

Procedures section.

6. Install the ignition coils. Refer to

Maintenance Procedures section.

Testing the Engine Coollant Densiity

If antifreeze is not replaced, test its

density.

1. Flushing connector

The antifreeze replacement and a

The following hose can be fabricated

density test should be performed by

to ease draining procedure.

an authorized Sea-Doo dealer, repair

shop or person of your own choosing.

Refer to Maintenance Schedule.

NOTICE

Improper antifreeze densiity may

TYPICAL

result in freeziing of the lliquiid iin

1. Flushing connector adapter

the coolling system iif the water-

2. Hose 12.7 mm (1/2 in)

craft iis stored in an area where

3. Air hose male adapter

the freezing point is attained. This

would seriouslly damage the

NOTICE

engine.

Faiilure to drain the exhaust sys-

tem may cause severe damage to

Ellectriicall System

the exhaust manifold.

Battery

Remove special tools.

Battery Maiintenance

Lubriicating the Engiine Cyliinders

When storing the watercraft, the bat-

tery should always be stored in a

1. Remove spark plugs. Refer to

warm, dry place.

Maintenance Procedures section.

2. Spray lubricant in each cylinder

WARNING

through spark plug holes.

Never charge or boost the battery

Serviice Product

whille installled in the watercraft.

XPS Anti-Corrosive Lubricant or

This vehicle is equipped with a main-

equivalent

tenance-free type battery, there is no

3. Fully depress the throttle lever. De-

pressing the throttle lever will

157

STORAGE AND PRESEASON PREPARATION

need to add water to adjust electrolyte

NOTE: Remove any water or debris

level.

if present in the compartment before

installing the battery.

NOTICE

Never remove the battery striip

NOTICE

from caps or add ellectrolyte for

Reversed battery pollarity wiilll

the liife of the battery.

damage the voltage regulator.

Removiing the Battery

NOTICE

1. Remove the seat.

2. Disconnect the battery cables.

Allways connect the RED (+) cablle

first, then the BLACK (-) cable.

NOTICE

Always disconnect the BLACK (-)

2. Tighten the battery cable screws to

cable first, then the RED (+)

specification.

cable.

Tighteniing Torque

Battery

4 ± 0.5 Nm

cable screw

(35 ± 4 lbf-in)

3. Apply dielectric grease on battery

posts.

4. Cover positive battery post with

rubber boot.

5. Verify

cable

routing

and

attachments.

1. Battery post

Engine Compartment

2. Strap

3. Remove the retaining strap.

Clleaniing the Engine Compartment

1. Clean the bilge with hot water and

Chargiing the Battery

detergent or with bilge cleaner.

Use any automotive type battery

2. Rinse thoroughly.

charger. Always refer to the battery

3. Lift front end of watercraft to com-

charger manufacturer’s instructions.

pletely drain bilge through the bilge

drain plugs.

Cleaning the Battery

Clean battery casing and battery

Antiicorrosion Treatment

posts using a soft brush and a solution

1. Wipe off any residual water in the

of baking soda and water.

engine compartment.

2. Lubricate all metallic components

Remove corrosion from battery cable

in engine compartment.

terminals and battery posts using a

firm wire brush.

Rinse with clear water then dry well.

Installling the Battery

1. Connect the battery cables.

158

STORAGE AND PRESEASON PREPARATION

Preseason Preparation

Serviice Product

The preseason preparation must be

Lubricant and anti-corrosive or

performed in conjunction with the

equivalent

Maintenance Schedule.

Ensure to perform all tasks included in

NOTE:

the Every Year or 100 Hours table.

The seat should be removed during

storage. This will prevent engine com-

Preseason preparation maintenance

partment condensation and possible

may be performed by an authorized

corrosion.

Sea-Doo dealer, repair shop or per-

son of your own choosing.

Sonar Transducer

Inspect level of coolant under the

transducer by removing it.

1. Release holding tabs

2. Lift transducer

Ensure there is enough liquid, approx-

imately up to locking tie level.

Refer to Technical Specifications for

type and quantity of liquid.

Body and Hulll

Repair, clean and protect the water-

craft as per procedures in Watercraft

Care section.

159

IDENTIFICATION NUMBERS

The main components of the watercraft (engine and hull) are identified by differ-

ent serial numbers. It may sometimes become necessary to locate these num-

bers for warranty purposes or to trace the watercraft in the event of theft.

Hull Identification Number

The Hull Identification Number (HIN)

is located on footboard at the rear of

watercraft.

TYPICAL

1. Engine Identification Number (EIN)

Engine Manufacturer

Identification

TYPICAL

1. Hull Identification Number (HIN)

It is composed of 12 digits:

ENGINE MANUFACTURER IDENTIFICA-

TION LABEL

YDV

12345

L 8

Model year

Year of production

Month of production

Serial number

(a letter may also be used as a

digit)

Manufacturer

Engine Identification Number

The Engine Identification Number

(EIN) is located on the front end of the

LABEL LOCATION

engine.

170

COMPLIANCE

EPA Compliance Label

EMISSION CONTROL SYSTEM INFORMATION

BOMBARDIER RECREATIONAL PRODUCTS INC.

THIS ENGINE CONFORMS TO

U.S. EPA & CALIFORNIA

EMISSIONS REGULATIONS FOR MARINE SI ENGINES.

RENSEIGNEMENT SUR LE DISPOSITIF ANTIPOLLUTION

CE MOTEUR EST CONFORME AUX NORMES

DE L’EPA

DES É.-U. POUR LES MOTEURS MARINS À ALLUMAGE COMMANDÉ.

ENGINE FAMILY / FAMILLE DE MOTEUR

( EPA

FEL)

CERTIFICATION STANDARDS

NORMES DE CERTIFICATION

(

FEL

)

EMISSION CONTROL SYSTEM

SYSTÈME DE CONTRÔLE DES ÉMISSIONS

MEETS

CALIFORNIA EVAP EMISSIONS REGULATIONS FOR SPARK

IGNITION MARINE WATERCRAFT. EVAP FAMILY

EVAPORATIVE EMISSION CONTROL SYSTEM: SO

SEE OPERATOR’S GUIDE FOR MAINTENANCE SCHEDULE AND FUEL,

OIL AND SPARK PLUG SPECIFICATIONS. VOIR LE CALENDRIER

D’ENTRETIEN ET LES SPÉCIFICATIONS D’ESSENCE, D’HUILE ET DE

BOUGIE D’ALLUMAGE DANS LE GUIDE DE L’OPÉRATEUR.

219905703

EPA COMPLIANCE LABEL

TYPICAL – LABEL LOCATION

173

RF D.E.S.S. KEY

This device complies with FCC Part 15 and Industry Canada license exempt

RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

IC Registration Number: 12006A-1001317030

FCC ID: 2ACER-1001317030

We, the party responsible for compliance, declare under our sole responsibility

that the device is in conformity with the provisions of the following Council Direc-

tive: 2014/53/EU. To which this declaration relates is in conformity with the es-

sential requirements and other relevant requirements. The product is in

conformity with the following directives, harmonized standards and regulations:

Radio Equipment Directive (RED) 2014/53/EU and Harmonized Standards:

EN 300 330-2, EN 60950-1

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

This device contains licence-exempt transmitter (s)/receiver (s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS

(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique Can-

ada applicables aux appareils radio exempts de licence. L’exploitation est autori-

sée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage;

(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-

lage est susceptible d'en compromettre le fonctionnement.

176

MULTIFUNCTION GAUGE REGULATORY

INFORMATION

Techniicall Information

Changes or modifications not ex-

pressly approved by the party respon-

Transmitter:

sible for compliance could void the

- BT operating frequency range:

user's authority to operate the

2402 - 2480 MHz

equipment.

- BT version: 4.2 (no BTLE)

IC: 22868 - VDIBRHS01

- BT output power: < 8.5 dBm

FCC ID: 2AMJS - VDIBRHS01

Receiver:

- FM operating range: 76 - 108 MHz

RF exposure:

Manufacturer and Address

1. The equipment complies with FCC

RF exposure limits set forth for an

Manufacturer:

uncontrolled environment.

- Robert Bosch LLC

2. This equipment must be installed

and operated with a separation

Address:

distance of at least 20 cm from all

38000 Hills Tech Drive,

persons.

Farmington Hills, MI 48331,

3. The antenna(s) used for this trans-

USA

mitter must not be co-located or

operating in conjunction with any

To display the regulatory information

other antenna or transmitter.

on the vehicle digital display: From the

home screen, access the main menu

Mexiico

and keep the joystick pressed down

for more than 10 seconds.

IFETEL

USA and Canada

Marca: Robert Bosch LLC

This device complies with FCC Part

Modelo(s): VIPHI2BT

and Industry Canada license

Número: RCPBOVI18-0967

exempt RSS standard(s). Operation is

subject to the following two conditions:

NOM-208-SCFI-2016

(1) this device may not cause interfer-

ence, and

La operación de este equipo está su-

(2) this device must accept any inter-

jeta a las siguientes dos condiciones:

ference, including interference that

(1) es posible que este equipo o dis-

may cause undesired operation of the

positivo no cause interferencia perju-

device.

dicial y (2) este equipo o dispositivo

debe aceptar cualquier interferencia,

Le présent appareil est conforme aux

incluyendo la que pueda causar su

CNR d'Industrie Canada applicables

operación no deseada.

aux appareils radio exempts de li-

cence. L'exploitation est autorisée aux

Braziil

deux conditions suivantes:

(1) l'appareil ne doit pas produire de

brouillage, et

(2) l'utilisateur de l'appareil doit ac-

cepter tout brouillage radioélectrique

subi, même si le brouillage est sus-

ceptible

d'en compromettre le

03473-18-04473

fonctionnement.

178

MULTIFUNCTION GAUGE REGULATORY INFORMATION

Este equipamento opera em caráter

This device should not be modified

secundário, isto é, não tem direito a

(otherwise the granted designation

proteção contra interferência prejudi-

number will become invalid).

cial, mesmo de estações do mesmo ti-

Europe

po, e não pode causar interferência a

sistemas operando em caráter

Decllaratiion of Conformity

primário.

Simplified EU Declaration of Conform-

Japan

ity according Radio Equipment Direc-

tive 2014/53/EU

This device is granted pursuant to the

Japanese Radio Law (

) and

the Japanese Telecommunications

Business Law (

179

MULTIFUNCTION GAUGE REGULATORY INFORMATION

Hiermit erklärt Robert Bosch LLC, dass der Funkanlagentyp VIPHI2BT der Richtlinie 2014/53/EU entspricht.

Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: eu-doc.

bosch.com

Le soussigné, Robert Bosch LLC, déclare que l'équipement radioélectrique du type VIPHI2BT est conforme à la

directive 2014/53/UE.

Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante:eu-doc.

bosch.com

Robert Bosch LLC

VIPHI2BT

2014/53/.

: eu-doc.

bosch.com

Με την παρούσα ο/η Robert Bosch LLC, δηλώνει ότι ο ραδιοεξοπλισ×όØ VIPHI2BT πληροί την οδηγία 2014/53/EE.

Το πλήρεØ κεί×ενο τηØ δήλωσηØ συ××όρφωσηØ ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: eu-doc.

bosch.com

Tímto Robert Bosch LLC prohlašuje, že typ rádiového zařízení VIPHI2BT je v souladu se směrnicí 2014/53/EU.

Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: eu-doc.bosch.com

Hermed erklærer Robert Bosch LLC, at radioudstyrstypen VIPHI2BT er i overensstemmelse med direktiv

2014/53/EU.

EU-overensstemmelseserklæringens fulde tekst kan ðndes på følgende internetadresse: eu-doc.bosch.com

Käesolevaga deklareerib Robert Bosch LLC, et käesolev raadioseadme tüüp VIPHI2BT vastab direktiivi

2014/53/EL nõuetele.

ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: eu-doc.bosch.com

Por la presente, Robert Bosch LLC declara que el tipo de equipo radioeléctrico VIPHI2BT es conforme con la

Directiva 2014/53/UE.

El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: eu-doc.

bosch.com

Robert Bosch LLC vakuuttaa, että radiolaitetyyppi VIPHI2BT on direktiivin 2014/53/EU mukainen.

EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: eu-doc.

bosch.com

Hereby, Robert Bosch LLC declares that the radio equipment type VIPHI2BT is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: eu-doc.bosch.com

Robert Bosch LLC ovime izjavljuje da je radijska oprema tipa VIPHI2BT u skladu s Direktivom 2014/53/EU.

Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: eu-doc.bosch.com

Robert Bosch LLC igazolja, hogy a VIPHI2BT típusú rádióberendezés megfelel a 2014/53/EU irányelvnek.

Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: eu-doc.bosch.com

Il fabbricante, Robert Bosch LLC, dichiara che il tipo di apparecchiatura radio VIPHI2BT è conforme alla direttiva

2014/53/UE.

Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: eu-doc.

bosch.com

180

MULTIFUNCTION GAUGE REGULATORY INFORMATION

Aš, Robert Bosch LLC, patvirtinu, kad radijo įrenginių tipas VIPHI2BT atitinka Direktyvą 2014/53/ES.

Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: eu-doc.bosch.com

Ar šo Robert Bosch LLC deklarē, ka radioiekārta VIPHI2BT atbilst Direktīvai 2014/53/ES.

Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: eu-doc.bosch.com

B'dan, Robert Bosch LLC, niddikjara li dan it-tip ta' tagħmir tar-radju VIPHI2BT huwa konformi mad-Direttiva

2014/53/UE.

It-test kollu tad-dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: eu-doc.

bosch.com

Hierbij verklaar ik, Robert Bosch LLC, dat het type radioapparatuur VIPHI2BT conform is met Richtlijn

2014/53/EU.

De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: eu-doc.

bosch.com

Robert Bosch LLC niniejszym oświadcza, że typ urządzenia radiowego VIPHI2BT jest zgodny z dyrektywą

2014/53/UE.

Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: eu-doc.bosch.com

O(a) abaixo assinado(a) Robert Bosch LLC declara que o presente tipo de equipamento de rádio VIPHI2BT está

em conformidade com a Diretiva 2014/53/UE.

O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: eu-doc.

bosch.com

Prin prezenta, Robert Bosch LLC declară că tipul de echipamente radio VIPHI2BT este în conformitate cu

Directiva 2014/53/UE.

Textul integral al declaraFiei UE de conformitate este disponibil la următoarea adresă internet: eu-doc.bosch.com

Härmed försäkrar Robert Bosch LLC att denna typ av radioutrustning VIPHI2BT överensstämmer med direktiv

2014/53/EU.

Den fullständiga texten till EU-försäkran om överensstämmelse Knns på följande webbadress: eu-doc.bosch.com

Robert Bosch LLC potrjuje, da je tip radijske opreme VIPHI2BT skladen z Direktivo 2014/53/EU.

Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: eu-doc.bosch.com

Robert Bosch LLC týmto vyhlasuje, že rádiové zariadenie typu VIPHI2BT je v súlade so smernicou 2014/53/EÚ.

Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: eu-doc.bosch.com

Robert Bosch LLC lýsir því hér með yKr að þráðlausi _arskiptabúnaðurinn VIPHI2BT er í samræmi við tilskipun

2014/53/ESB.

Óstyttan texta ESB-samræmisyKrlýsingarinnar er að Knna á ve{anginu: eu-doc.bosch.com

Liechtenstein

Hiermit erklärt Robert Bosch LLC, dass der Funkanlagentyp VIPHI2BT der Richtlinie 2014/53/EU entspricht.

Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: eu-doc.

bosch.com

Hermed erklærer Robert Bosch LLC at radioutstyrstypen VIPHI2BT er i samsvar med direktiv 2014/53/EU.

Hele teksten i EU-samsvarserklæringen Knnes på følgende internettadresse: eu-doc.bosch.com

~ Robert Bosch LLC ,

VIPHI2BT

2014/53/EU.

eu-doc.bosch.com.

181

BRP AUDIO SYSTEM

This equipment has been tested and

FCC ID: 2AAOY - 278003465

found to comply with the limits for a

Class B digital device, pursuant to

L’émetteur/ récepteur exempt de li-

Part 15 of the FCC rules. These limits

cence contenu dans le présent appa-

are designed to provide reasonable

reil

est

conforme aux CNR

protection against harmful interfer-

d’Innovation, Sciences et Développe-

ment économique Canada applica-

ence in a residential installation.

bles aux appareils radio exempts de

This equipment generates, uses, and

licence. L’exploitation est autorisée

can radiate radio frequency energy

aux deux conditions suivantes :

and, if not installed and used in ac-

(1) l'appareil ne doit pas produire de

cordance with the instructions, may

brouillage;

cause harmful interference to radio

communications. However, this is no

(2) l'appareil doit accepter tout brouil-

guaranty that interference will occur in

lage radioélectrique subi, même si le

a particular installation.

brouillage est susceptible d'en com-

promettre le fonctionnement.

If this equipment does cause harmful

interference to radio or television re-

Radio Equipment Directive

(RED)

ception, which can be determined by

2014/53/EU

and

Harmonized

turning the equipment off or on, you

Standards:

are encouraged to try to correct the in-

ETSI EN 300 328 V2.1.1

terference by one or more of the fol-

(2016-11)

lowing measure:

ETSI EN301 489-1 V2.1.1

- Reorient or relocate the receiving

(2017-02)

antenna.

ETSI EN301 489-17 V3.1.1

- Increase the separation between

(2017-02)

the equipment and receiver.

62479:2010

- Connect the equipment to an out-

let on a different circuit than the

one to which the receiver is

connected.

- Consult the dealer or an experi-

enced radio/TV technician for help.

Changes or modifications not ex-

pressly approved by Mitek Corpora-

tion could void the user's authority to

operate this equipment. This device

complies with Part

15 of the FCC

rules.

Operation is subject to the following

two conditions:

(1) This device may not cause

harmful interference, and

(2) This device must accept any in-

terference received, including in-

terference that may cause

undesired operation.

Registration

Number:

22793-278003465

182

ENGINE EMISSIONS INFORMATION

Manufacturer''s

EPA Emission Regulations

Responsibility

Sea-Doo SIPME manufactured by

Manufacturers of marine engines

BRP are certified to the EPA as con-

must determine the exhaust emission

forming to the requirements of the reg-

levels for each engine horsepower

ulations for the control of air pollution

family and certify these engines with

from new SIPME. This certification is

the United States of America Environ-

contingent on certain adjustments

mental Protection Agency (EPA). An

being set to factory standards. For this

emissions control information label,

reason, the factory procedure for serv-

showing emission levels and engine

icing the product must be strictly fol-

specifications, must be placed on

lowed and, whenever practicable,

each Spark-Ignition Propulsion Marine

returned to the original intent of the

Engines

(SIPME) at the time of

design.

manufacture.

The responsibilities listed above are

general and in no way a complete list-

Dealer''s Responsibility

ing of the rules and regulations per-

When performing service on a Sea--

taining to the EPA requirements on

Doo SIPME that carry an emissions

exhaust emissions for marine prod-

control information label, adjustments

ucts. For more detailed information on

must be kept within published factory

this subject, you may contact:

specifications.

U. S. Environmental Protection

Replacement or repair of any emis-

Agency

sion related component must be exe-

Certification Division

cuted in a manner that maintains

Gasoline Engine Compliance Center

emission levels within the prescribed

2000 Traverwood Drive

certification standards.

Ann Arbor MI 48105

USA

Dealers are not to modify the engine

in any manner that would alter the

horsepower or allow emission levels

EPA INTERNET WEB SITE:

to exceed their predetermined factory

www.epa.gov/otaq

specifications.

Evaporative Emission

Exceptions include manufacturer's

Control System

prescribed changes, such as altitude

adjustments for example.

Spark-Ignition Marine Watercraft

(SIMW) sold in the State of California

Owner’s Responsibility

are certified to the California evapora-

tive emissions regulations for SIMW of

The owner/operator is required to

the California Air Resources Board

have engine maintenance performed

(13 CCR 2850 to 2869). These mod-

to maintain emission levels within pre-

els are equipped with an evaporative

scribed certification standards.

emission control system consisting of

Low Permeation Fuel Tank (LPFT),

The owner/operator is not to, and

Low Permeation Fuel Line (LPFL) and

should not allow anyone to modify the

a Pressure Relief Valve (PRV).

engine in any manner that would alter

the horsepower or allow emissions

levels to exceed their predetermined

factory specifications.

183

ENGINE

Rotax 1630 ACE - 170

Engiine

4-stroke, Single Over Head

Engine type

Camshaft (SOHC)

Declared Power

(Declared power as per ISO 8665 at

125 kW @ 8000 RPM

propeller-shaft.)

Induction

Naturally-Aspirated

Number of cylinders

12 valves with hydraulic

Number of valves

lifters (no adjustment)

100 mm

Bore

(3.9 in)

69.2 mm

Stroke

(2.7 in)

1 630.5 cm³

Displacement

(99.5 in³)

Compression ratio

11:1

Fuell System

Multipoint fuel injection with

iTC (intelligent Throttle

Fuel injection type

Control).

Single throttle body (60

mm) with an actuator

Idle speed (not adjustable)

1800 ± 50 RPM

Electriicall System

IDI (Inductive Discharge

Ignition system type

Ignition)

NGK, DCPR8E with solid

Type

Spark plug

post or equivalent

(Do not attempt to adjust

gap on this spark plug.)

0.80 to 0.90 mm

Gap

(.031 to .035 in)

188

VEHICLE

FishPro SPORT

170 and TROPHY 170

Cooliing System

Closed-loop cooling system

Type

(CLCS)

XPS Extended life pre-mixed

Recommended

coolant

Use a low silicate, extended

life ethylene-glycol premixed

Alternative, or if

coolant (50%-50%)

Coolant

not available

specifically formulated for

internal combustion

aluminum engines.

5.4 l

Capacity

(5.7 qt(liq.,US))

Fuell System

Fuel pump

In-tank electrical

Regular unleaded

Type

Refer to Fuel Requirements

Fuel

87 Pump Posted AKI

(RON+MON)/2

Octane rating

(RON) E10

Full

70 l (18.5 gal(liq. US))

Tank capacity

Reserve

(from low level

14 l (3.7 gal(liq. US))

signal - approx.)

Electriicall System

Sport

12 V, 18 Ah

Battery

Trophy

2 X 12 V, 18 Ah

Sport

420 W @ 6000 RPM

Total system output

Trophy

650 W @ 6000 RPM

Fuel Inj., Ign.

Coils and Fuel

15 A

Fuses

Pump

Bilge pump

190

VEHICLE

Livewell pump

(if equipped)

Cluster

iBR

30 A

F10

Start/ Stop

F11

ECM

F12

Battery

30 A

Diagnostic

F13

15 A

Tool 2

Diagnostic

F14

15 A

Tool 1

Fuse Holder

Transducer

RY1

Main

—

Relay

RY2

Livewell pump

—

Recommend

BRP Extended life pre-mixed

coolant

Use a low silicate, extended

Alternate oil if

life ethylene glycol premixed

XPS products

coolant (50%-50%)

Transducer Liquid

are not

specifically formulated for

available

internal combustion

aluminium engines

135 ml

Capacity

(4.6 fl oz(US))

Propulsion

Propulsion system

Sea-Doo® jet pump

Axial flow, single stage.

Type

Large hub with double row

Jet pump

ball bearings

Material

Aluminum

Impeller

Stainless steel

Transmission

Type

Direct drive

191

VEHICLE

Weight and Loadiing Capaciity

386 kg

Sport

(852 lb)

Sport

(With

395 kg

Dry weight

sound

(871 lb)

system)

416 kg

Trophy

(938 lb)

Number of passenger (driver incl.)

Load limit (passenger(s), luggage, including

272 kg (600 lb)

accessories)

98.9 l

(26.1 gal(liq.,US))

Storage capacity

51 l

(13.5 gal(liq.,US))

Dimensions

373.4 cm

Overall length

(147 in)

125.5 cm

Overall width

(49.4 in)

115.1 cm

Overall height

(45.3 in)

NOTE:

BRP reserves the right to make changes in design and specifications and/or to

make additions to, or improvements in its products without imposing any obliga-

tion upon itself to install them on its products previously manufactured.

192

TROUBLESHOOTING GUIDELINES

ENGINE WILL NOT START

1. Tether cord removed.

- Press START/STOP button.

- Install tether cord cap over engine cut-off switch within 5 seconds after

depressing the START/STOP button.

- Press START/STOP button.

2. ECM does not recogniize the D.E.S.S. key.

- Refer to an authorized Sea-Doo dealer.

3. Burnt fuse: maiin, ellectric starter or ECM.

- Check wiring then replace fuse(s).

4. Diischarged battery.

- Refer to an authorized Sea-Doo dealer.

WARNING

Do not charge or boost the battery whille iinstallled on the watercraft.

Electrollyte iis poisonous and dangerous. Avoiid contact with eyes, skin

and clothing.

5. Battery connectiions, corroded or lloose. Bad ground.

- Refer to an authorized Sea-Doo dealer.

6. Water-fllooded engiine.

- Refer to Water-Flooded Engine in Special Procedures.

7. Faulty sensor or ECM.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

8. Seized jet pump.

- Try to clean. Otherwise, refer to an authorized Sea-Doo dealer.

ENGINE CRANKS SLOWLY

1. Loose battery cable connectiions.

- Check/clean/tighten.

2. Diischarged or weak battery.

- Refer to an authorized Sea-Doo dealer.

3. Worn starter.

- Refer to an authorized Sea-Doo dealer.

194

TROUBLESHOOTING GUIDELINES

ENGINE TURNS NORMALLY BUT WILL NOT START

1. Fuell tank empty or water-contaminated.

- Refill. Siphon and fill with fresh fuel.

2. Foulled/defectiive spark pllugs.

- Replace.

3. Blown fuse.

- Check wiring then replace fuse(s).

4. Water-fllooded engine.

- Refer to Water-Flooded Engine in Special Procedures.

5. Engiine management system faullt detected (check engine pillot llamp

is ON).

– Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

6. Faullty fuell pump.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

ENGINE MISFIRES, RUNS IRREGULARLY

1. Foulled/defectiive/worn spark pllugs.

- Replace.

2. Fuell: Levell too llow, stalle or water-contamiinated.

- Siphon and/or refill.

3. Faullty iigniitiion coill(s).

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

4. Clogged injectors.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

5. Engiine management system faullt detected (check engine pillot llamp

is ON).

– Refer to Monitoring System.

195

TROUBLESHOOTING GUIDELINES

ENGINE SMOKE

1. Oill levell too hiigh.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

2. Water ingestiion, coollant lleak or damaged cyllinder head gasket.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

3. Internall engiine damage.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

ENGINE OVERHEATS

1. Cllogged exhaust system.

- Flush exhaust system.

2. Engine coollant level too low.

- Refer to Maintenance Procedures.

3. Quiick connect adapter lleft iin fllushiing connector.

- Remove adapter from flushing connector and retry watercraft. If

problem persists, seek service from an authorized Sea-Doo dealer,

repair shop, or person of your own choosing for maintenance, repair, or

replacement. Please refer to the US EPA Emission-Related Warranty

contained herein for information about warranty claims.

196

TROUBLESHOOTING GUIDELINES

ENGINE LACKS ACCELERATION OR POWER

Learning key used.

- Use a Normal key.

Not in Sport mode.

- Select Sport mode.

Jet pump water iintake cllogged.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

Damaged iimpelller or worn-out wear riing.

- Replace. Refer to an authorized Sea-Doo dealer.

Engiine oiil llevell too high.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

Weak spark.

- Refer to ENGINE MISFIRES, RUNS IRREGULARLY.

Engiine management system faullt detected (check engine pillot llamp

is ON).

– Refer to Monitoring System.

Clogged injectors.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

Low fuel pressure.

- Seek service from an authorized Sea-Doo dealer, repair shop, or

person of your own choosing for maintenance, repair, or replacement.

Please refer to the US EPA Emission-Related Warranty contained

herein for information about warranty claims.

10. Water iin fuell.

- Siphon and replace.

11. Engiine damaged by water ingestiion.

- Refer to an authorized Sea-Doo dealer.

197

TROUBLESHOOTING GUIDELINES

WATERCRAFT CAN NOT REACH TOP SPEED

1. Jet pump water intake clogged.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

2. Damaged impelller or worn-out wear ring.

- Replace. Refer to an authorized Sea-Doo dealer.

3. Engine management system fault detected (check engiine piilot lamp

is ON).

- Refer to Monitoring System.

WATERCRAFT STAYS IN NEUTRAL AFTER OPERATING THE iBR

LEVER

1. The iBR gate stays in neutrall.

- Release the throttle to idle RPM.

iBR WILL NOT RETURN TO NEUTRAL POSITION (iiBR INDICATOR

LIGHT ON)

1. iBR jjammed wiith debris.

- Clean and check for damage in the iBR gate and nozzle area.

2. iBR system malfunctiion.

- Remove tether cord, wait four minutes, reinstall key and check iBR light

to ensure fault is cleared.

- Refer to an authorized Sea-Doo dealer if fault persists or reoccurs

frequently.

iBR WILL NOT RETURN TO NEUTRAL POSITION (IBR INDICATOR

LIGHT OFF)

1. Throttle llever not fullly released during operation.

- Release throttle lever fully to ensure iBR gate returns to neutral.

2. Throttle llever does not fullly return to nulll when relleased.

- Refer to an authorized Sea-Doo dealer.

198

TROUBLESHOOTING GUIDELINES

ABNORMAL NOISE FROM PROPULSION SYSTEM

1. Weeds or debriis jammed around impelller.

- Clean. Refer to Jet Pump Water Intake and Impeller Cleaning in Special

Procedures section.

- Check for damage.

2. Damaged iimpelller shaft or drive shaft.

- Refer to an authorized Sea-Doo dealer.

3. Water iintrusion iin jjet pump causiing bearing seiizure.

- Refer to an authorized Sea-Doo dealer.

WATER FOUND IN BILGE

1. Baiiler system malfunctiion.

- Have system inspected by an authorized Sea-Doo dealer.

2. Exhaust system leak.

- Refer to an authorized Sea-Doo dealer.

3. Carbon riing at drive shaft worn.

- Refer to an authorized Sea-Doo dealer.

199

MONITORING SYSTEM

A system monitors the electronic com-

Fault codes can be viewed in the infor-

ponents of the EMS (engine manage-

mation center multifunction display

ment system) iBR, and other

however, this function is only available

components of the electrical system.

if a fault is still active.

When a fault occurs, it sends visual

messages through the information

If there is an active fault code, it may

be viewed by the operator on the mul-

center and/or audible signals through

tifunction display. The operator may

a beeper to inform you of a particular

then choose to call his authorized

condition.

Sea-Doo dealer to pass on the fault

A fault code may also be recorded.

code. The dealer will then advise the

operator on the steps to take to solve

When a minor or transient fault oc-

the problem, or to stop using the

curs, the fault message and beeper

watercraft and to bring it in to the deal-

will cease automatically if the condi-

er for repairs.

tion that caused the fault does not ex-

ist anymore.

Diispllayiing Faullt Codes

Releasing the throttle and letting the

Select CODES. If a fault code has oc-

engine return to idle speed may allow

curred during your riding cycle, a CO-

normal operation to come back. If this

DES menu will be available in the

does not work, try removing and rein-

settings menu. Press OK to see the

stalling the tether cord on the engine

list of faults.

cut-off switch.

NOTE:

The electronic system will react differ-

During normal riding conditions some

ently depending on the fault type. In

fault codes may occur. Before con-

severe failure, the engine may not be

tacting your local dealer, remove the

allowed to be started. In other cases,

key, make sure to wait 2 minutes until

the engine will operate in limp home

the electrical system shuts down, then

mode (reduced speed).

press start to wake up the electrical

system. This will ensure occurred fault

When a fault occurs, please refer to

to disappear and only the active codes

the US EPA Emission-Related War-

will remain ON in the CODES menu.

ranty contained herein for information

about warranty claims.

Fault Codes

IVTS

When a fault occurs, a numerical fault

code may be recorded depending on

the fault type and system.

These fault codes are used by author-

ized Sea-Doo dealers for trouble-

shooting the watercraft systems when

comparing them to a fault list.

Indicator Lights and Message Display Information

The indicator lights (pilot lamps) and messages displayed in the information cen-

ter will inform you of a particular condition or if an anomaly occurs.

For information on usual indicator lights, refer to appropriate digital display.

200

MONITORING SYSTEM

Indiicator

Liight / Icon

Message Display

Descriiptiion

(ON)

LOW or HIGH

BATTERY

Low/high battery voltage

VOLTAGE

HIGH

Engine or exhaust system overheating

TEMPERATURE

CHECK ENGINE

Check engine (minor fault req. maint.) or

or LIMP HOME

LIMP HOME MODE (major eng. fault)

MODE

LOW OIL

Low oil pressure

PRESSURE

Light is steady with a buzzer and a

IBR MODULE

check engine light: iBR system fault

ERROR

(refer to an authorized Sea-Doo dealer)

Light is flashing: iBR system fault (refer

to an authorized Sea-Doo dealer)

Light is steady with no buzzer:

iBR system still functional but needs to

be inspected by an authorized Sea-Doo

dealer

Pivotal Seat

When pedestal is installed

Installed

Light is steady with a buzzer and a

Pivotal Seat Fault

exclamation mark light: Pivotal Seat fault

(refer to an authorized Sea-Doo dealer)

Message Diispllay Informatiion

HIGH EXHAUST TEMPERATURE

High exhaust temperature detected

HIGH ENGINE TEMPERATURE

High engine temperature detected

Engine system malfunction or

CHECK ENGINE

maintenance required

Major fault detected, engine power

LIMP HOME MODE

limited

FUEL SENSOR FAULT

Fuel level sensor fault

WATER TEMP SENSOR

Problem with water temperature sensor,

DEFECTIVE

not sending water temperature info.

201

MONITORING SYSTEM

Beeper Code Information

Beeper Codes

Description

Bad D.E.S.S. system connection.

Reinstall tether cord cap correctly on the engine

cut-off switch.

Wrong D.E.S.S. key.

Use a tether cord that has been programmed for the

watercraft.

Defective D.E.S.S. key.

Use another tether cord with programmed D.E.S.S.

key.

1 long beep

(while installing tether

Defective engiine cut-off swiitch.

cord on watercraft

Refer to an authorized Sea-Doo dealer.

engine cut-off switch)

Improper operatiion of ECM or defective wiriing

harness.Seek service from an authorized Sea-Doo

dealer, repair shop, or person of your own choosing

for maintenance, repair, or replacement. Please

refer to the US EPA Emission-Related Warranty

contained herein for information about warranty

claims.

Improper pivotall seat installlation.

Refer to an authorized Sea-Doo dealer.

Engine management system faullt.

Seek service from an authorized Sea-Doo dealer,

repair shop, or person of your own choosing for

A 2 seconds beep

maintenance, repair, or replacement. Please refer to

every 15 minutes

the US EPA Emission-Related Warranty contained

interval

herein for information about warranty claims.

iBR system faullt.

Refer to an authorized Sea-Doo dealer.

A 2 seconds beep

Low fuell level.

every 10 minutes

Refill fuel tank. If problem persists, refer to an

interval

authorized Sea-Doo dealer.

Hiigh engine temperature coolant.

See Engine Overheating.

Low oill pressure.

2 second beeps

Turn off engine as soon as possible. Check oil level

and refill. Seek service from an authorized Sea-Doo

dealer, repair shop, or person of your own choosing

for maintenance, repair, or replacement. Please

refer to the US EPA Emission-Related Warranty

203

BRP LIMITED WARRANTY – USA AND CANADA:

2024 SEA-DOO PERSONAL WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its

2024 Sea-Doo

watercraft (“Product(s)”) sold by authorized BRP Dealers (as hereinafter defined)

in the United States of America ("USA") and in Canada from defects in material

or workmanship for the period and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM STATE TO STATE, OR PROVINCE TO PROVINCE.

Neither the distributor, any BRP dealer nor any other person has been authorized

to make any affirmation, representation or warranty regarding the product, other

than those contained in this limited warranty, and if made, shall not be enforce-

able against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

- Normal wear and tear;

- Routine maintenance items, tune ups, adjustments;

- Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

- Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

206

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

resulting from repairs done by a person that is not an authorized servicing

BRP dealer;

- Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

- Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

- Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

- Damages from rust, corrosion or exposure to the elements;

- Damage resulting from water or snow ingestion;

- Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work;

- Damages from cooling system or jet pump blockage by foreign material; and

- Damages related to gel coat finish including but not limited to cosmetic gel

coat finish, blisters or fiberglass delamination caused by blisters, crazing, spi-

der or hairline cracks.

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWELVE (12) consecutive months, for private use owners.

2. FOUR (4) consecutive months, for commercial use owners.

A Product is used commercially when it is used in connection with any work or

employment that generates income during any part of the warranty period. A

Product is also used commercially when, at any point during the warranty period,

it is licensed for commercial use.

1. For emission-related components, please also refer to the US EPA Emis-

sion-Related Warranty.

2. For Sea-Doo personal watercrafts produced by BRP for sale in the State of

California or New York that are originally sold to a resident or subsequently

warranty registered to a resident in the State of California or New York,

please also refer to the applicable California and New York Emissions Control

Warranty Statement contained herein.

3. For Sea-Doo personal watercrafts produced by BRP for sale in the State of

California that are originally sold to a resident or subsequently warranty regis-

tered to a resident in the State of California, please also refer to the California

Evaporative Emissions Control System Warranty Statement contained

herein.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this limited warranty beyond its original expiration

date.

5) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

207

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

1. The Product must be purchased as new and unused by its first owner from a

Dealer authorized to sell the Products in the country in which the sale oc-

curred (“Dealer”);

2. The BRP specified pre-delivery inspection process must be completed, docu-

mented and signed by the purchaser;

3. The Product must have undergone proper registration by an authorized

Dealer;

4. The Product must be purchased in the country in which the purchaser

resides;

5. Routine maintenance outlined in the Operator’s Guide must be timely per-

formed in order to maintain warranty coverage. BRP reserves the right to

make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

6) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP dealer within three (3) days of the appearance of the

anomaly and provide the Dealer with reasonable access to the Product and rea-

sonable opportunity to repair it.

The customer must also present to the Dealer, proof of purchase of the Product

and must sign the repair/work order prior to starting the repair in order to validate

the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

7) WHAT BRP WILL DO

BRP’s obligations under this warranty are limited to, at its sole discretion, repair-

ing or replacing parts found defective under normal use, maintenance and serv-

ice without charge for parts and labor, at any authorized BRP dealer during the

warranty coverage period under the conditions described herein. No claim of

breach of warranty shall be cause for cancellation or rescission of the sale of the

Product to the owner.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

8) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

208

BRP LIMITED WARRANTY - USA AND CANADA: 2024 SEA-DOO PERSONAL WATERCRAFT

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

9) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized dealer's service manager or

owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

209

US EPA EMISSION-RELATED WARRANTY

Bombardier Recreational Products Inc. (“BRP”) warrants to the ultimate purchas-

er and each subsequent purchaser that this new engine, including all parts of its

exhaust emission-control system and its evaporative emission-control system,

meets two conditions:

1. It is designed, built, and equipped so it conforms at the time of sale to the ulti-

mate purchaser with the requirements of 40 CFR 1045 and 40 CFR 1060It.

2. It is free from defects in materials and workmanship that may keep it from

meeting the requirements of 40 CFR 1045 and 40 CFR 1060.

Where a warrantable condition exists, BRP will repair or replace, as it elects, any

part or component with a defect in materials or workmanship that would increase

the engine’s emissions of any regulated pollutant within the stated warranty peri-

od at no cost to the owner, including expenses related to diagnosing and repair-

ing or replacing emission-related parts. All defective parts replaced under this

warranty become the property of BRP.

For all emission-related warranty claims, BRP is limiting the diagnosis and repair

of emission-related parts to the authorized Sea-Doo dealers, unless for emer-

gency repairs as required by item 2 of the following list.

As a certifying manufacturer, BRP will not deny emission-related warranty claims

based on any of the following:

1. Maintenance or other service BRP or BRP's authorized facilities performed.

2. Engine/equipment repair work that an operator performed to correct an un-

safe, emergency condition attributable to BRP as long as the operator tries to

restore the engine/equipment to its proper configuration as soon as possible.

3. Any action or inaction by the operator unrelated to the warranty claim.

4. Maintenance that was performed more frequently than BRP specify.

5. Anything that is BRP fault or responsibility

6. The use of any fuel that is commonly available where the equipment operates

unless BRP written maintenance instructions state that this fuel would harm

the equipment’s emission control system and operators can readily find the

proper fuel. See maintenance information section and fuel requirements of fu-

eling section.

Emission-Related Warranty Period

The emission-related warranty is valid for the following period whichever comes

first:

Hours

Months

Exhaust

175

emission-related

components

Evaporative

N/A

emission-related

components

210

US EPA EMISSION-RELATED WARRANTY

Components Covered

The emission-related warranty covers all components whose failure would in-

crease an engine’s emissions of any regulated pollutant, including the following

listed components:

For exhaust emissions, emission-related components include any engine

parts related to the following systems:

- Air-induction system

- Fuel system

- Ignition system

- Exhaust gas recirculation systems

The following parts are also considered emission-related components for ex-

haust emissions:

- Aftertreatment devices

- Crankcase ventilation valves

- Sensors

- Electronic control units

The following parts are considered emission-related components for evapora-

tive emissions:

- Fuel tank

- Fuel cap

- Fuel line

- Fuel line fittings

- Clamps*

- Pressure relief valves*

- Control valves*

- Control solenoids*

- Electronic controls*

- Vacuum control diaphragms*

- Control cables*

- Control linkages*

- Purge valves

- Vapor hoses

- Liquid/ vapor separator

- Carbon canister

- Canister mounting brackets

- Carburetor purge port connector

NOTE:

* As related to the evaporative emission control system.

4. Emission-related components also include any other part whose only purpose

is to reduce emissions or whose failure will increase emissions without signifi-

cantly degrading engine/ equipment performance.

Limited Applicability

As a certifying manufacturer, BRP may deny emission-related warranty claims

for failures that have been caused by the owner’s or operator’s improper mainte-

nance or use, by accidents for which the manufacturer has no responsibility, or

211

US EPA EMISSION-RELATED WARRANTY

by acts of God. For example, an emission-related warranty claim need not be

honored for failures that have been directly caused by the operator’s abuse of

the engine/ equipment or the operator’s use of the engine/equipment in a manner

for which it was not designed and are not attributable to the manufacturer in

anyway.

If you have any question regarding your warranty rights and responsibility or for

the name and location of the nearest authorized BRP dealer, you should contact

BRP by filling out the customer contact form at www.brp.com or contact BRP by

mail at one of the addresses listed under the CONTACT US section of this guide,

or call at 1-888-272-9222.

212

CALIFORNIA EVAPORATIVE EMISSIONS

CONTROL SYSTEM WARRANTY STATEMENT

Your Warranty Rights and Obligations

The California Air Resources Board is pleased to explain the evaporative emis-

sions control system’s warranty on your 2024 spark-ignition marine watercraft

(SIMW). In California, new spark-ignition marine watercraft must be designed,

built, and equipped to meet the State’s stringent anti-smog standards. Bombar-

dier Recreational Products Inc. must warrant the evaporative emissions control

system on your spark-ignition marine watercraft for the period listed below, pro-

vided there has been no abuse, neglect or improper maintenance of your spar-

k-ignition marine watercraft.

Your evaporative emissions control system may include parts such as: canisters,

carburetors, clamps, connectors, filters, fuel caps, fuel lines, fuel tanks, valves,

vapor hoses, and other associated evaporative emissions control system

components

Manufacturer’s Warranty Coverage

This evaporative emissions control system is warranted for two years. If any

evaporative emission-related part on your spark-ignition marine watercraft is de-

fective, the part will be repaired or replaced by Bombardier Recreational Prod-

ucts Inc.

Parts covered:

1. Clamp(s)*

2. Fuel Cap

3. Fuel Line(s)

4. Fuel Line Fitting(s)

5. Fuel Tank

6. Pressure Relief Valve(s)*

7. Vapor Hose(s)

8. All other parts not listed that may affect the evaporative emissions control

system

NOTE:

* As related to the evaporative emission control system.

Owner’s Warranty Responsibilities

As the spark-ignition marine watercraft owner, you are responsible for perform-

ance of the required maintenance listed in your owner’s manual. Bombardier

Recreational Products Inc. recommends that you retain all receipts covering

maintenance on your spark-ignition marine watercraft, but Bombardier Recrea-

tional Products Inc. cannot deny warranty solely for the lack of receipts.

As the spark-ignition marine watercraft owner, you should however be aware that

Bombardier Recreational Products Inc. may deny you warranty coverage if your

spark-ignition marine watercraft or a part has failed due to abuse, neglect, im-

proper maintenance or unapproved modifications.

You are responsible for presenting your spark-ignition marine watercraft to a

Bombardier Recreational Products Inc. distribution center or service center as

213

CALIFORNIA AND NEW YORK EMISSION

CONTROL WARRANTY STATEMENT FOR MODEL

YEAR 2024 SEA-DOO® PERSONAL WATERCRAFT

Your Warranty Rights and Obligations

The California Air Resources Board, the New York State Department of Environ-

mental Conservation and Bombardier Recreational Products Inc. ("BRP") are

pleased to explain the emission control system warranty on your Model Year

2024 Sea-Doo personal watercraft. In California and New York, new personal

watercraft engines must be designed, built and equipped to meet the State’s

stringent anti-smog standards. BRP must warrant the emission control system

on your personal watercraft engine for the period of time listed below provided

there has been no abuse, neglect or improper maintenance of your watercraft

engine.

Your emission control system may include parts such as the fuel injection sys-

tem, the ignition system and catalytic converter. Also included may be hoses,

belts, connectors and other emission related assemblies.

Where a warrantable condition exists, BRP will repair your personal watercraft

engine at no cost to you including diagnosis, parts and labor provided that such

work is performed by an authorized BRP dealer.

Manufacturer’s Limited Warranty Coverage

This emission limited warranty covers Model Year 2024 Sea-Doo personal water-

crafts certified and produced by BRP for sale in California or New York, that are

originally sold in California or New York to a California or New York resident or

subsequently warranty registered to a California or New York resident. The BRP

limited warranty conditions for Sea-Doo personal watercrafts are still applicable

to these models with the necessary modifications. Select emission control parts

of your 2024 Sea-Doo personal watercraft are warranted from the date of deliv-

ery to the first retail consumer for a period of 4 years, or for 250 hours of use,

whichever occurs first. However, warranty coverage based on the hourly period

is only permitted for personal watercraft equipped with the appropriate hour me-

ters or their equivalent. If any emission-related part on your engine is defective

under warranty, the part will be repaired or replaced by BRP.

Parts Covered for a Model Year 2024 Sea-Doo Personall Watercraft

Supercharger

Air intake adapter

Throttle position sensor

Spark plugs

Intake manifold air pressure sensor

Ignition coils

Intake manifold air temperature

Air box

sensor

Engine temperature sensor

Intake and exhaust valve and seals

Knock sensor

Intake manifold

215

CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2024

SEA-DOO® PERSONAL WATERCRAFT

Engine control module ECM

Crankcase ventilation valve

Throttle body

Throttle body seal

Ful rail

Intake manifold seal

Fuel injectors

Wire harness and connectors

Fuel pressure regulator

Fuel filter

Fuel pump

The emission warranty covers damage to other engine components that is

caused by the failure of a warranted part. The BRP operator’s guide provided

contains written instructions for the proper maintenance and use of your personal

watercraft. All emission warranty parts are warranted by BRP for the entire war-

ranty period of the personal watercraft, unless the part is scheduled for replace-

ment as required maintenance in the operator’s guide.

Emission warranty parts that are scheduled for replacement, as required mainte-

nance, are warranted by BRP for the period of time before the first scheduled re-

placement date for that part. Emission warranty parts that are scheduled for

regular inspection, but not regular replacement, are warranted by BRP for the en-

tire warranty period of the personal watercraft. Any emission warranty part re-

paired or replaced under the terms of this warranty statement is warranted by

BRP for the remainder of the warranty period of the original part. All parts re-

placed under this limited warranty become the property of BRP

Maintenance receipts and records should be transferred to each subsequent

owner of the personal watercraft.

Owner’’s Warranty Responsiibillities

As the owner of a 2024 Sea-Doo personal watercraft, you are responsible for the

performance of the required maintenance listed in your operator’s guide. BRP

recommends that you retain all receipts covering maintenance of your personal

watercraft engine, but BRP cannot deny warranty solely for the lack of receipts or

your failure to ensure the performance of all scheduled maintenance

As the owner of a Sea-Doo personal watercraft, you should however be aware

that BRP may deny your warranty coverage if your engine or a part has failed

due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your engine to an authorized BRP Sea-Doo

dealer as soon as a problem exists. The warranty repairs will be completed in a

reasonable amount of time, not to exceed 30 days

If you have any questions regarding your warranty rights and responsibilities or

for the name and location of the nearest authorized BRP Sea-Doo dealer you

should contact the Customer Assistance Center at 1-888-272-9222.

216

CALIFORNIA AND NEW YORK EMISSION CONTROL WARRANTY STATEMENT FOR MODEL YEAR 2024

SEA-DOO® PERSONAL WATERCRAFT

Star Rating System

For California and New York, your 2024 Sea-Doo watercraft (SIMW) has a spe-

cial environmental label required by the California Air Resources Board. The la-

bel has 3 stars. A hangtag, provided with the Product (SIMW), describes the

meaning of the star rating system.

The Star Label Means Clleaner Marine Engiines

The Symbol for Cleaner Marine Engines:

Clleaner Air and Water

For a healthier lifestyle and environment.

Better Fuel Economy

Burns up to 30 - 40 percent less gas and oil than conventional carbureted two-s-

troke engines saving money and resources.

Longer Emiissiion Warranty

Protects consumer for worry free operation.

One Star – Low Emission

The one-star label identifies personal watercraft, outboard, stern drive and in-

board engines that meet the Air Resources Board’s Personal Watercraft and Out-

board marine engine 2001 exhaust emission standards. Engines meeting these

standards have 75% lower emissions than conventional carbureted two-stroke

engines. These engines are equivalent to the U.S. EPA’s 2006 standards for ma-

rine engines.

Two Stars – Very Low Emiissiion

The two-star label identifies personal watercraft, outboard, stern drive and in-

board engines that meet the Air Resources Board’s Personal Watercraft and Out-

board marine engine 2004 exhaust emission standards. Engines meeting these

standards have 20% lower emissions than One Star - Low-Emission engines.

Three Stars – Ulltra Low Emiissiion

The three-star label identifies engines that meet the Air Resources Board’s Per-

sonal Watercraft and Outboard marine engine 2008 exhaust emission standards

or the Stern drive and Inboard marine engine 2003 exhaust emission standards.

Engines meeting these standards have 65% lower emissions than One Star -

Low Emission engines.

Four Stars – Super Ulltra Low Emiissiion

217

BRP INTERNATIONAL LIMITED WARRANTY: 2024

SEA-DOO® WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

(“Product(s)”) sold by distributors or dealers authorized by BRP to distribute the

Products outside of the United States of America ("USA"), Canada, member

states of the European Economic Area (which is comprised of the states of the

European Union plus the United Kingdom, Norway, Iceland and Liechtenstein)

("EEA"), Turkey, member states of the Commonwealth of the Independent States

(including Ukraine and Turkmenistan) ("CIS") from defects in material or work-

manship for the period and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM COUNTRY TO COUNTRY. BRP SHALL NOT BE HELD LIABLE IF

PRODUCTS OR WARRANTY PARTS ARE NOT AVAILABLE IN CERTAIN

COUNTRIES FOR REASONS OUTSIDE OF BRP’S CONTROL.

For Products purchased in Australia, refer to the Australia-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

219

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

Damages from rust, corrosion or exposure to the elements;

–

Damage resulting from water or snow ingestion;

–

Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work;

Damages from cooling system or jet pump blockage by foreign material;

–

Damages to gel coat finish including but not limited to cosmetic gel coat finish

defects, blisters, starring, crazing and fiberglass delamination caused by blis-

ters, crazing, spider or hairline cracks.

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWELVE (12) consecutive months, for private use owners. For AUSTRALIA

and NEW ZEALAND only, TWENTY-FOUR (24) consecutive months for pri-

vate, recreational use.

2. FOUR (4) consecutive months, for commercial use owners. A Product is used

commercially when it is used in connection with any work or employment that

generates income during any part of the warranty period. A Product is also

used commercially when, at any point during the warranty period, it is li-

censed for commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty

period which can be extended by any applicable warranty promotional program,

as the case may be.

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

220

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

FOR PRODUCTS SOLD IN AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian

Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensa-

tion for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

Nothing in these Warranty terms and conditions should be taken to exclude, re-

strict or modify the application of any condition, warranty, guarantee, right or rem-

edy conferred or implied under the Competition and Consumer Act 2010 (Cth),

including the Australian Consumer Law or any other law, where to do so would

contravene that law, or cause any part of these terms and conditions to be void.

The benefits given to you under this limited warranty are in addition to other rights

and remedies that you have under Australian law.

5) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

A) The Product must be purchased as new and unused by its first owner

from a Distributor/Dealer authorized to distribute Products in the country in

which the sale occurred (“Distributor/Dealer”);

B) The BRP specified pre-delivery inspection process must be completed,

documented and signed by the purchaser;

C) The Product must have undergone proper registration by an authorized

Distributor/Dealer;

D) The Product must be purchased in the country in which the purchaser

resides;

E) Routine maintenance outlined in the Operator’s Guide must be timely

performed in order to maintain warranty coverage. BRP reserves the right

to make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

6) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

221

BRP INTERNATIONAL LIMITED WARRANTY: 2024 SEA-DOO® WATERCRAFT

All parts replaced under this limited warranty become the property of BRP.

7) WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, the

owner will bear responsibility for any additional charges due to local practices

and conditions, such as, but not limited to, freight, insurance, taxes, license fees,

import duties, and any and all other financial charges, including those levied by

governments, states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

8) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

9) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

222

BRP LIMITED WARRANTY FOR THE EUROPEAN

ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024

SEA-DOO® PERSONAL WATERCRAFT

1) SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024 Sea-Doo per-

sonal watercraft (“Product(s)”) sold by distributors or dealers authorized by BRP

to distribute the Products in member states of the European Economic Area

(which is comprised of the states of the European Union plus the United King-

dom, Norway, Iceland and Liechtenstein) ("EEA"), Turkey, member states of the

Commonwealth of the Independent States (including Ukraine and Turkmenistan)

("CIS") (“Distributor/Dealer”) from defects in material or workmanship for the peri-

od and under the conditions described below.

This limited warranty will become null and void if:

1. the Product was used for racing or any other competitive activity, at any point,

even by a previous owner; or

2. the Product has been altered or modified in such a way so as to adversely af-

fect its operation, performance or durability, or has been altered or modified

to change its intended use.

Non-factory installed parts and accessories are not covered under this limited

warranty. Please refer to the applicable parts and accessories limited warranty

text.

2) LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EXPRESSLY

GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-

RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-

POSE. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE

EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME

STATES/PROVINCES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITA-

TIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS,

AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH MAY VARY

FROM STATE TO STATE, OR PROVINCE TO PROVINCE. BRP SHALL NOT

BE HELD LIABLE IF PRODUCTS OR WARRANTY PARTS ARE NOT AVAIL-

ABLE IN CERTAIN COUNTRIES FOR REASONS OUTSIDE OF BRP’S

CONTROL.

For Products purchased in France, refer to the France-specific section below.

Neither the distributor, any BRP Distributor/Dealer nor any other person has

been authorized to make any affirmation, representation or warranty regarding

the product, other than those contained in this limited warranty, and if made, shall

not be enforceable against BRP.

223

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

BRP reserves the right to modify this limited warranty at any time, being under-

stood that such modification will not alter the warranty conditions applicable to

the Products sold while this warranty is in effect.

3) EXCLUSIONS–ARE NOT WARRANTED

The following are not warranted under any circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper maintenance and/

or storage, as described in the Operator's Guide;

Damage resulting from removal of parts, improper repairs, service, mainte-

nance, modifications or use of parts not manufactured or approved by BRP or

resulting from repairs done by a person that is not an authorized servicing

BRP Distributor/Dealer;

Damage caused by abuse, abnormal use, neglect or operation of the product

in a manner inconsistent with the recommended operation described in the

Product’s Operator’s Guide;

Damage resulting from accident, submersion, fire, theft, vandalism or any act

of God;

Operation with fuels, oils or lubricants which are not suitable for use with the

Product (see the Operator’s Guide);

Damages from rust, corrosion or exposure to the elements;

–

Damage resulting from water or snow ingestion;

–

Incidental or consequential damages, or damages of any kind including with-

out limitation transportation expenses, towing, storage, telephone, rental, taxi,

inconvenience, insurance coverage, loan payments, loss of time, loss of in-

come or time missed for downtime experience due to service work.

Damages from cooling system or jet pump blockage by foreign material;

–

Damages to gel coat finish including but not limited to cosmetic gel coat finish

defects, blisters, starring, crazing and fiberglass delamination caused by blis-

ters, crazing, spider or hairline cracks

4) WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to the first retail

consumer, or (2) the date the product is first put into use, whichever occurs first

and for the applicable period below:

1. TWENTY-FOUR (24) consecutive months, for private, recreational use.

2. FOUR (4) consecutive months, for commercial use owners. A Product is used

commercially when it is used in connection with any work or employment that

generates income during any part of the warranty period. A Product is also

used commercially when, at any point during the warranty period, it is li-

censed for commercial use.

The repair or replacement of parts or the performance of service under this war-

ranty does not extend the life of this warranty beyond its original expiration date.

The warranty coverage period identified above are a minimal limited warranty

period which can be extended by any applicable warranty promotional program,

as the case may be.

224

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

Note that the duration and any other modalities of the warranty coverage are sub-

ject to the applicable national or local legislation in the customer's country.

5) FOR PRODUCTS SOLD IN FRANCE ONLY

The seller shall deliver goods that are complying with the contract and shall be

responsible for defects existing upon delivery. The seller shall also be responsi-

ble for defects resulting from packaging, assembling instructions or the installa-

tion when it is its responsibility per the contract or if accomplished under its

responsibility. To be compliant with the contract, the good shall:

1. Be fit for normal use for goods similar thereto and, if applicable:

- Correspond to the description provided by the seller and have the qualities

presented to the buyer though sample or model;

- Have the qualities that a buyer may legitimately expect considering the

public declarations of the seller, the manufacturer of its representative, in-

cluding in advertising or labeling; or

2. Have the characteristics mutually agreed upon as between the parties or be

fit for the specific use intended by the buyer and brought to the attention of

the seller and which accepted.

The action for failure to comply is prescribed after two years after delivery of the

goods. The seller is responsible for the warranty for hidden defects of the good

sold if such hidden defects are rendering the good unfit for the intended use, or if

they diminish its use in such a way that the buyer would not have acquired the

good or would have given a lesser price, had he known. The action for such hid-

den defects shall be taken by the buyer within 2 years of the discovery of the

defect.

6) CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following conditions has

been fulfilled:

A) The Product must be purchased as new and unused by its first owner

from a Distributor/Dealer authorized to distribute Products in the country (or

in the case of the EEA, union of countries) in which the sale occurred (“Dis-

tributor/Dealer”);

B) The BRP specified pre-delivery inspection process must be completed,

documented and signed by the purchaser;

C) The Product must have undergone proper registration by an authorized

Distributor/Dealer;

D) The Product must be purchased in the country (or in the case of the

EEA, union of countries) in which the purchaser resides;

E) Routine maintenance outlined in the Operator’s Guide must be timely

performed in order to maintain warranty coverage. BRP reserves the right

to make warranty coverage contingent upon proof of proper maintenance.

BRP will not honor this limited warranty to any private use owner or commercial

use owner if one of the preceding conditions has not been met. Such limitations

are necessary in order to allow BRP to preserve both the safety of its products,

and also that of its consumers and the general public.

225

BRP LIMITED WARRANTY FOR THE EUROPEAN ECONOMIC AREA, THE COMMONWEALTH OF THE

INDEPENDENT STATES AND TURKEY: 2024 SEA-DOO® PERSONAL WATERCRAFT

7) WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The customer must cease using the Product upon the appearance of an anom-

aly, notify a servicing BRP Distributor/Dealer within two (2) months of the appear-

ance of the anomaly and provide the Distributor/Dealer with reasonable access

to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local legislation in

customer's country.

The customer must also present to the Distributor/Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the repair in or-

der to validate the warranty repair.

All parts replaced under this limited warranty become the property of BRP.

8) WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty are limited

to, at its sole discretion, repairing or replacing parts found defective under normal

use, maintenance and service without charge for parts and labor, at any author-

ized BRP Distributor/Dealer during the warranty coverage period under the con-

ditions described herein. No claim of breach of warranty shall be cause for

cancellation or rescission of the sale of the Product to the owner. You may have

other legal rights which may vary from country to country.

In the event that service is required outside of the country of original sale, or for

EEA residents, if service is required outside of the EEA, the owner will bear re-

sponsibility for any additional charges due to local practices and conditions, such

as, but not limited to, freight, insurance, taxes, license fees, import duties, and

any and all other financial charges, including those levied by governments,

states, territories and their respective agencies.

BRP reserves the right to improve or modify products from time to time without

assuming any obligation to modify products previously manufactured.

9) TRANSFER

If the ownership of a Product is transferred during the warranty coverage period,

this limited warranty, subject to its terms and conditions, shall also be transferred

and be valid for the remaining coverage period provided BRP or an authorized

Product Distributor/Dealer receives a proof that the former owner agreed to the

transfer of ownership, in addition to the coordinates of the new owner.

10) CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited warranty,

BRP suggests that you try to resolve the issue at the dealership level. We recom-

mend discussing the issue with the authorized Distributor/Dealer's service man-

ager or owner.

If the matter still remains unresolved, contact BRP by filling out the customer con-

tact form at www.brp.com or contact BRP by mail at one of the addresses listed

under the Contact Us section of this guide.

226

DATA PRIVACY INFORMATION

Bombardier Recreational Products inc., its affiliates and subsidiaries (“BRP”) is

committed to protecting your privacy and support a general policy of openness

about how we collect, use and disclose your personal information in the course

of managing our relationship with you. More detaiils can be found by visiting

BRP’’s Priivacy Poliicy at:

https://brp.com/en/privacy-poliicy.htmll or by scanniing the QR Code below.

Please be assured that we have appropriate security measures in place to en-

sure that your personal information is protected against loss and unauthorized

access.

Your personal information that may be collected by BRP, directly from you or

from authorized dealers or authorized third parties, includes:

- Contact, Demographiic & Registratiion Informatiion (e.g., name, full ad-

dress, phone number, email, gender, ownership history, language of

communication)

- Vehicle Information (e.g., serial number, purchase and delivery date, unit

usage, vehicle location and movements)

- Third Party Informatiion (e.g., information received from BRP partners, join-

t-marketing activities information, social media)

- Technological Information (e.g., IP address, type of device, operating sys-

tem, browser type, webpages you view, cookies and similar technologies

when you use BRP or dealers’ websites or mobile application)

- Interaction with BRP Information (e.g., information collected when you call

BRP’s in-house sales representatives, buy items on a BRP web Site, sign up

for BRP emails, participate in BRP-sponsored contests and sweepstakes or

attend BRP-sponsored events)

- Transactiionall Informatiion (e.g., information necessary to handle returns,

payment information when you purchase our products or services through

our websites or mobile applications and other issues related to your purchase

of BRP products)

This information may be used and processed for the following purposes:

- Safety & Security

- Customer Support for Sales & After Sales (e.g., complete or follow up with

you about your purchase or maintenance)

- Registration & Warranty

- Communication (e.g., sending you a BRP satisfaction survey)

- Online Behavioural Advertising, Profiling and Location-Based Services

(e.g., offer customized experience)

- Compliance & Dispute Resolution

- Marketing & Advertising

- Assistance (e.g., help with any delivery issues, handle returns, and other is-

sues related to your purchase of BRP products).

We also may use personal information to generate aggregated or statistical data

that no longer identifies you personally.

Your personal informatiion may be disclosed to the folllowiing: BRP, BRP’s

authoriized deallerships, diistriibutors, serviice proviiders, advertising & mar-

ket research partners and other authoriized third partiies.

We may receive information about you from diverse sources, including third par-

ties, such as BRP’s authorized dealerships and partners, with whom we offer

228

DATA PRIVACY INFORMATION

services or engage in joint-marketing activities. We may also receive information

about you from social media platforms such as Facebook and Twitter, when you

interact with us on those platforms.

Depending on the circumstances, your personal information may be communi-

cated outside the region where you reside. Your personal information is retained

only for as long as necessary for the purpose for which we obtained it and ac-

cording to our retention policies.

To exercise your data privacy rights (e.g. right of access, right of rectification), to

withdraw your consent in order to be removed from the address list for marketing

purposes or for the satisfaction survey or for general data privacy questions,

please contact BRP’s Data Protection Officer at or by mail at privacyoffii-

cer@brp.com or by mail at:

BRP Legal Service, 726 St-Joseph, Valcourt, Quebec, Canada, J0E 2L0.

When BRP processes your personall iinformation, they do so in complliance

wiith its Privacy Pollicy avaiilable at: https://www.brp.com/en/privacy-poliicy.

htmll or by using the folllowiing

QR Code.

229

www.brp.com

Asia Pacific

Australia

Level 26

477 Pitt Street

Sydney, NSW 2020

China

上海市徐汇区衡山路10号6号楼301

Rm 301, Building 6,

No.10 Heng Shan Rd,

Shanghai, China

Japan

21F Shinagawa East One Tower

2-16-1 Konan, Minato-ku-ku,

Tokyo 108-0075

New Zealland

Suite 1.6, 2-8 Osborne Street,

Newmarket, Auckland 2013

Europe, Middle East and Africa

Bellgium

Oktrooiplein 1

9000 Gent

Czech Republiic

Stefanikova 43a

Prague 5

150 00

Germany

Itterpark 11

40724 Hilden

Fiinland

Isoaavantie 7

PL 8040

96101 Rovaniemi

France

Arteparc Bâtiment B

Route de la côte d'Azur,

13 590 Meyreuil

Norway

Ingvald Ystgaardsvei 15

N-7484 Trondheim

230

CHANGE OF ADDRESS/OWNERSHIP

If your address has changed or if you are the new owner of the boat, be sure to

notify BRP by either:

- Notifying an authorized Sea-Doo dealer.

- North America Only: calling at 1 888 272-9222.

- Mailing one of the change of address cards on the following pages at one of

the BRP addresses indicated in the Contact Us section of this guide.

In case of change of ownership, please join a proof that the former owner agreed

to the transfer.

Notifying BRP, even after the expiration of the limited warranty, is very important

as it enables BRP to reach the boat owner if necessary, like when safety recalls

are initiated. It is the owner’s responsibility to notify BRP.

STOLEN UNITS: In the event that your boat is stolen, you should notify your

area’s distributor warranty department of such. We will ask you to provide your

name, address, phone number, Hull Identification Number and date it was stolen.

232

BRP Sea-Doo FISHPRO SPORT AND TROPHY SERIES. OPERATOR’S GUIDE (2024) - page 2