Nissan Qashqai (2007-2010). Manual - part 662

SERVICE DATA AND SPECIFICATIONS (SDS)

RAX-5

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[2WD]

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000000970499

Axial end play

0.05 mm (0.002 in) or less

RAX-6

< SYMPTOM DIAGNOSIS >

[4WD]

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

SYMPTOM DIAGNOSIS

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NVH Troubleshooting Chart

INFOID:0000000000970500

Use chart below you find the cause of the symptom. If necessary, repair or replace these parts.

×

: Applicable

Reference page

—

RAX-18

—

RAX-13

—

NVH in DLN section

NVH in DLN section

NVH in RAX

 and RSU 

sections

Refer to REAR AXLE i

n

 t

h

is chart

NVH in WT 

section

NVH in WT 

section

Ref

e

r t

o

 DRIVE

 SHAFT

 in this 

chart

NVH in BR 

section

Possible cause and SUSPECTED PARTS

Ex

ce

ss

iv

e j

o

in

t an

gl

e

Jo

in

t s

lid

in

g re

si

st

an

ce

Im

b

a

lanc

e

Im

p

rop

er i

n

s

ta

lla

tio

n

, 

loo

s

en

es

s

P

a

rt

s interference

PR

OP

EL

LE

R

 S

H

A

F

T

DIFFERENTIAL

REA

R

 AXLE AND REAR S

U

SPENSION

REA

R

 AXLE

TI

RE

S

ROAD W

H

EEL

DRIV

E

 SHAFT

BR

AK

E

S

Symptom

DRIVE 
SHAFT

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

REAR AXLE

Noise

×

×

×

×

×

×

×

×

×

Shake

×

×

×

×

×

×

×

×

Vibration

×

×

×

×

×

×

Shimmy

×

×

×

×

×

×

Judder

×

×

×

×

×

Poor quality ride or handling

×

×

×

×

×

PRECAUTIONS

RAX-7

< PRECAUTION >

[4WD]

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

PRECAUTION

PRECAUTIONS

Precautions for Drive Shaft

INFOID:0000000001117166

CAUTION:

Note the following precautions when disassembling and assembling drive shaft.
• Joint sub-assembly does not disassemble because it is non-overhaul parts.
• Perform work in a dust-free location.
• Before disassembling and assembling, clean the parts.
• Prevent the entry of foreign objects during disassembly of the service location.
• Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a

clean cover must be placed over parts.

• Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint

adhering to parts.

• Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be

removed by blowing with air or wiping with paper shop cloths.

RAX-8

< PREPARATION >

[4WD]

PREPARATION

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000000970502

Tool number 
Tool name

Description

KV38100500
Drift
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.

Installing sensor rotor

KV40101840
Color
a: 67 mm (2.64 in) dia.
b: 85 mm (3.35 in) dia.

Installing sensor rotor

ZZA0701D

ZZA1113D