Nissan Qashqai (2007-2010). Manual - part 654

FAX-38

< ON-VEHICLE REPAIR >

[2WD]

FRONT DRIVE SHAFT

13. Pinch projection on the band with suitable pliers to tighten band.

14. Insert tip of band below end of the pawl.
15. Secure housing and shaft, and then make sure that they are in

the correct position when rotating boot. Install them with new
boot band when the mounting positions become incorrect.

16. Install circular clip to shaft (left side).

CAUTION:

Never reuse circular clip.

17. Install dust shield (left side).

CAUTION:

Never reuse dust shield.

Support Bearing

1.

Install dust shield on housing.

CAUTION:

Never reuse dust shield.

2.

Press support bearing onto housing.

3.

Install snap ring.

CAUTION:

Never reuse snap ring.

4.

Install dust shields.

CAUTION:

Never reuse dust shields.

Dynamic Damper

Secure dynamic damper with bands in the following specified posi-
tion when removing.

CAUTION:

Never reuse bands.

Wheel Side

For further details, refer to the installation procedure of “

FAX-11, "Replacement"

” for the drive shaft boot.

K9K MODELS : Inspection

INFOID:0000000001070386

SDIA3558E

YAX007

YAX008

Standard

Demission : 

FAX-40, "Drive Shaft"

.

FAC0156D

FRONT DRIVE SHAFT

FAX-39

< ON-VEHICLE REPAIR >

[2WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace if there are.

Dynamic Damper

Check damper for cracks or wear. Replace if necessary.

Joint Sub-Assembly (Wheel Side)

Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.

Housing and Spider assembly (Transaxle Side)

Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.

Support Bearing (Right Side)

Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.

Support Bearing Bracket (Right Side)

Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.

SDIA1190J

FAX-40

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[2WD]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000000970490

Drive Shaft

INFOID:0000000000970491

HR16DE

MR20DE

M/T models

Axial end play

0.05 mm (0.002 in) or less

Joint 

Wheel side

Transaxle assembly side

Grease quantity

Left side

100 – 120 g (3.53 – 4.23 oz)

155 – 175 g (5.47 – 6.17 oz)

Right side

Boots installed length (L)

Left side

131 mm (5.16 in)

172.4 mm (6.79 in)

Right side

Dynamic damper

A

B

Dimension

Left side

287 – 291 mm (11.30 – 11.46 in)

70 mm (2.76 in)

Right side

JPDIF0031ZZ

FAC0156D

Joint 

Wheel side

Transaxle assembly side

Grease quantity

Left side

115 – 135 g (4.06 – 4.76 oz)

95 – 105 g (3.35 – 3.70 oz)

Right side

113 – 123 g (3.99 – 4.34 oz)

SERVICE DATA AND SPECIFICATIONS (SDS)

FAX-41

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[2WD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

CVT models

Boots installed length (L)

Left side

133.5 mm (5.26 in)

185.6 mm (7.31 in)

Right side

177.6 mm (6.99 in)

Dynamic damper

A

B

Dimension

Left side

269 – 273 mm (10.59 – 10.75 in)

70 mm (2.76 in)

Right side

JPDIF0031ZZ

FAC0156D

Joint 

Wheel side

Transaxle assembly side

Grease quantity

Left side

115 – 135 g (4.06 – 4.76 oz)

200 – 220 g (7.05 – 7.76 oz)

Right side

Boots installed length (L)

Left side

133.5 mm (5.26 in)

185.6 mm (7.31 in)

Right side

177.6 mm (6.99 in)

Dynamic damper

A

B

JPDIF0031ZZ