Nissan Qashqai (2007-2010). Manual - part 617

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

DLN-41

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY30A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS

Description

INFOID:0000000000972113

Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.

Diagnosis Procedure

INFOID:0000000000972114

1.

PERFORM ECM SELF-DIAGNOSIS

With CONSULT-III

Perform ECM self-diagnosis.

Is any error system detected?

YES

>> Check the error system.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III

Perform 4WD control unit self-diagnosis.

Is DTC “U1000” detected?

YES

>> CAN specification chart. Refer to 

LAN-46, "Trouble Diagnosis Flow Chart"

.

NO

>> GO TO 3.

3.

CHECK 4WD SOLENOID

Perform the trouble diagnosis of the 4WD solenoid. Refer to 

DLN-16, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning part.

4.

CHECK ELECTRIC CONTROLLED COUPLING

1.

Turn the ignition switch OFF.

2.

Set the transmission to neutral. Release the parking brake.

3.

Lift up the vehicle.

4.

Rotate the propeller shaft by hand.

5.

Hold rear wheel of right and left lightly.

Does the front propeller shaft rotate?

YES

>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to

DLN-124, "Exploded View"

.

NO

>> Check each harness connector pin terminal for disconnection.

DLN-42

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY30A]

VEHICLE DOES NOT ENTER 4WD MODE

VEHICLE DOES NOT ENTER 4WD MODE

Description

INFOID:0000000000972115

Vehicle does not enter 4WD mode even though 4WD warning lamp turned to OFF.

Diagnosis Procedure

INFOID:0000000000972116

1.

CHECK 4WD WARNING LAMP

Turn the ignition switch ON.

Does 4WD warning lamp turn ON?

YES

>> GO TO 2.

NO

>> Go to 

DLN-39, "Diagnosis Procedure"

.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III

Perform 4WD control unit self-diagnosis.

Is DTC “U1000” detected?

YES

>> CAN specification chart. Refer to 

LAN-46, "Trouble Diagnosis Flow Chart"

.

NO

>> GO TO 3.

3.

CHECK 4WD SOLENOID

Perform the trouble diagnosis of the 4WD solenoid. Refer to 

DLN-16, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning part.

4.

CRUISE TEST

Drive the vehicle for a period of time.

Does any symptom occur?

YES

>> Replace electric controlled coupling for mechanical malfunction (mechanical engagement of

clutch is not possible). Refer to 

DLN-124, "Exploded View"

.

NO

>> Check each harness connector pin terminal for disconnection.

4WD WARNING LAMP BLINKS QUICKLY

DLN-43

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY30A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

4WD WARNING LAMP BLINKS QUICKLY

Description

INFOID:0000000000972117

While driving, 4WD warning lamp blinks 2 times in 1 second and it turns OFF after 1 minute.
• This symptom protects drivetrain parts when a heavy load is applied to the electric controlled coupling and

multiple disc clutch temperature increases. Also, optional distribution of torque sometimes becomes rigid
before lamp blinks quickly. Both cases are not malfunction.

• When this symptom occurs, stop vehicle and allow it to idle for some times. Blinking will stop and system will

be restored.

DLN-44

< SYMPTOM DIAGNOSIS >

[TRANSFER: TY30A]

4WD WARNING LAMP BLINKS SLOWLY

4WD WARNING LAMP BLINKS SLOWLY

Description

INFOID:0000000000972118

4WD warning lamp blinks at approximately 2 seconds intervals while driving.

Diagnosis Procedure

INFOID:0000000000972119

1.

CHECK TIRE

Check the following.
• Tire pressure
• Wear condition
• Longitudinal tire size (There is no difference between longitudinal tires.)

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Drive at vehicle speed of 20 km/h (12 MPH) or more for 5 seconds or more after repairing or

replacing damaged parts. (Initialize improper size tire information.)

2.

CHECK INPUT SIGNAL OF TIRE DIAMETER

With CONSULT-III

1.

Start engine.

2.

Drive at 20 km/h (12 MPH) or more for approx. 200 seconds.

3.

Check “DIS-TIRE MONI” of 4WD control unit CONSULT-III “DATA MONITOR”.

Does the item on “DATA MONITOR” indicate “0 - 4 mm”?

YES

>> INSPECTION END

NO

>> GO TO 3.

3.

TERMINAL INSPECTION

Check 4WD control unit harness connector for disconnection.
Is the inspection result normal?

YES

>> Replace 4WD control unit. Refer to 

DLN-56, "LHD : Exploded View"

 (LHD models), 

DLN-56,

"RHD : Exploded View"

 (RHD models).

NO

>> Repair or replace the malfunctioning part.