Nissan Qashqai (2007-2010). Manual - part 407

P1574 ASCD VEHICLE SPEED SENSOR

EC-1147

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Perform trouble shooting relevant to DTC indicated.

2.

CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”

Refer to 

BRC-17, "CONSULT-III Function (ABS)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace.

3.

CHECK COMBINATION METER

Check combination meter function.
Refer to 

MWI-23, "CONSULT-III Function (METER/M&A)"

.

>> INSPECTION END

EC-1148

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

P1706 PNP SWITCH

P1706 PNP SWITCH

Description

INFOID:0000000001094253

When the shift lever position is P or N (CVT), Neutral position (M/T), park/neutral position (PNP) switch is ON.
ECM detects the position because the continuity of the line (the ON signal) exists.

DTC Logic

INFOID:0000000001094254

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

INSPECTION START

Do you have CONSULT-III?
Do you have CONSULT-III?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

>> GO TO 3.

3.

CHECK PNP SWITCH FUNCTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “P/N POSI SW” in “DATA MONITOR” mode with CONSULT-III. Then check the “P/N POSI SW” sig-
nal under the following conditions.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Go to 

EC-1153, "Diagnosis Procedure"

.

4.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Select “DATA MONITOR” mode with CONSULT-III.

2.

Start engine and warm it up to normal operating temperature.

3.

Maintain the following conditions for at least 50 consecutive seconds.

CAUTION:

Always drive vehicle at a safe speed.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1706

Park/neutral position 
switch

The signal of the park/neutral position (PNP) 
switch is not changed in the process of engine 
starting and driving.

• Harness or connectors

[The park/neutral position (PNP) switch 
circuit is open or shorted.]

• Park/neutral position (PNP) switch

Position (Shift lever)

Known-good signal

N or P position (CVT)
Neutral position (M/T)

ON

Except above position

OFF

ENG SPEED

CVT: 1,500 - 6,375 rpm
M/T: 1,500 - 6,375 rpm

COOLAN TEMP/S

More than 70

°

C (158

°

F)

P1706 PNP SWITCH

EC-1149

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4.

Check 1st trip DTC.

Is 1st trip DTC detected?

YES

>> Go to 

EC-1153, "Diagnosis Procedure"

.

NO

>> INSPECTION END

5.

PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to 

EC-1153, "Component Function Check"

.

NOTE:
Use component function check the overall function of the park/neutral position (PNP) switch circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-1153, "Diagnosis Procedure"

.

Component Function Check

INFOID:0000000001094255

1.

PERFORM COMPONENT FUNCTION CHECK

1.

Turn ignition switch ON.

2.

Check the voltage between ECM harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC-1153, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000001094256

1.

CHECK PNP SWITCH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect Park/neutral position (PNP) switch harness connector.

3.

Turn ignition switch ON.

4.

Check the voltage between PNP switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

DTECTED MALFUNCTIONING PART

Check the following.
• Harness connectors E6, F123

B/FUEL SCHDL

CVT: 2.4 - 31.8 msec
M/T: 3.5 - 31.8 msec

VHCL SPEED SE

More than 64 km/h (40 mph)

Shift lever

Suitable position

ECM

Ground

Condition

Voltage

Connector

Terminal

F8

69

(PNP switch signal)

Ground

Shift lever

P or N (CVT)
Neutral (M/T)

Approx. 0V

Except above

BATTERY VOLTAGE

PNP switch

Ground

Voltage

Connector

Terminal

F21 (CVT)

7

Ground

Battery voltage

F46 (M/T 2W)

2

F48 (M/T 4W)

2

EC-1150

< COMPONENT DIAGNOSIS >

[MR20DE (WITHOUT EURO-OBD)]

P1706 PNP SWITCH

• Harness for open or short between PNP switch and IPDM E/R

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.

CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check the continuity between PNP switch harness connector and ECM harness connector.

4.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO-1

>> Repair open circuit or short to ground or short to power in harness or connectors. (M/T)

NO-2

>> GO TO 4. (CVT)

4.

CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II

1.

Check the continuity between PNP switch harness connector and ECM harness connector.

2.

Check the continuity between IPDM E/R harness connector and ECM harness connector.

3.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK PNP SWITCH

Refer to 

TM-227, "Component Inspection"

 (CVT) or 

TM-54, "PARK/NEUTRAL POSITION (PNP) SWITCH :

Component Inspection"

 (M/T).

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace PNP switch.

6.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

PNP switch

ECM

Continuity

Connector

Terminal

Connector

Terminal

F21 (CVT)

6

E10

102

Existed

F46 (M/T 2W)

3

F48 (M/T 4W)

1

PNP switch

IPDM E/R

Continuity

Connector

Terminal

Connector

Terminal

F21 (CVT)

7

E11

14

Existed

ECM

IPDM

Continuity

Connector

Terminal

Connector

Terminal

F8

69

E11

14

Existed