Nissan Qashqai (2007-2010). Manual - part 300

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-719

< FUNCTION DIAGNOSIS >

[MR20DE (WITH EURO-OBD)]

X: Applicable

*1: This item includes 1st trip DTCs.

*2: This mode includes 1st trip freeze frame data or freeze frame data. The items appear on CONSULT-II screen in freeze frame data
mode only if a 1st trip DTC or DTC is detected. For details, refer to

EC-706, "Diagnosis Description"

WORK SUPPORT MODE

Work Item

*: This function is not necessary in the usual service procedure.

SELF-DIAG RESULTS MODE

Self Diagnostic Item

Regarding items of DTC and 1st trip DTC, refer to

EC-962, "DTC Index"

Freeze Frame Data and 1st Trip Freeze Frame Data

*: The items are the same as those of 1st trip freeze frame data.

WORK ITEM

CONDITION

USAGE

FUEL PRESSURE RELEASE

• FUEL PUMP WILL STOP BY TOUCHING “START” DUR-

ING IDLING.
CRANK A FEW TIMES AFTER ENGINE STALLS.

When releasing fuel pressure from
fuel line

IDLE AIR VOL LEARN

• THE IDLE AIR VOLUME THAT KEEPS THE ENGINE

WITHIN THE SPECIFIED RANGE IS MEMORIZED IN
ECM.

When learning the idle air volume

SELF-LEARNING CONT

• THE COEFFICIENT OF SELF-LEARNING CONTROL

MIXTURE RATIO RETURNS TO THE ORIGINAL COEF-
FICIENT.

When clearing mixture ratio self-
learning value

TARGET IDLE RPM ADJ*

• IDLE CONDITION

When setting target idle speed

TARGET IGN TIM ADJ*

• IDLE CONDITION

When adjusting target ignition tim-
ing

Freeze frame data

item*

Description

DIAG TROUBLE
CODE
[PXXXX]

• The engine control component part/control system has a trouble code, it is displayed as PXXXX. (Refer to

EC-962, "DTC Index"

FUEL SYS-B1

• “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One mode in the following is displayed.

Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop

COOLANT TEMP [

or [

• The engine coolant temperature at the moment a malfunction is detected is displayed.

L-FUEL TRM-B1 [%]

• “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule than

short-term fuel trim.

S-FUEL TRM-B1 [%]

• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel sched-

ule.

ENGINE SPEED [rpm]

• The engine speed at the moment a malfunction is detected is displayed.

VEHICL SPEED
[km/h] or [mph]

• The vehicle speed at the moment a malfunction is detected is displayed.

ABSOL TH·P/S [%]

• The throttle valve opening angle at the moment a malfunction is detected is displayed.

B/FUEL SCHDL
[msec]

• The base fuel schedule at the moment a malfunction is detected is displayed.

INT/A TEMP SE [

or [

• The intake air temperature at the moment a malfunction is detected is displayed.

EC-720

< FUNCTION DIAGNOSIS >

[MR20DE (WITH EURO-OBD)]

ON BOARD DIAGNOSTIC (OBD) SYSTEM

DATA MONITOR MODE

Monitored Item

: Applicable

Monitored item

Unit

Description

Remarks

ENG SPEED

rpm

• Indicates the engine speed computed from the

signal of the crankshaft position sensor (POS)
and camshaft position sensor (PHASE).

• Accuracy becomes poor if engine

speed drops below the idle rpm.

• If the signal is interrupted while the

engine is running, an abnormal value
may be indicated.

MAS A/F SE-B1

• The signal voltage of the mass air flow sensor is

displayed.

• When the engine is stopped, a certain

value is indicated.

• When engine is running specification

range is indicated in “SPEC”.

B/FUEL SCHDL

msec

• “Base fuel schedule” indicates the fuel injection

pulse width programmed into ECM, prior to any
learned on board correction.

• When engine is running specification

range is indicated in “SPEC”.

A/F ALPHA-B1

• The mean value of the air-fuel ratio feedback cor-

rection factor per cycle is indicated.

• When the engine is stopped, a certain

value is indicated.

• When engine is running specification

range is indicated in “SPEC”.

• This data also includes the data for

the air-fuel ratio learning control.

COOLAN TEMP/S

C or

• The engine coolant temperature (determined by

the signal voltage of the engine coolant tempera-
ture sensor) is displayed.

• When the engine coolant temperature

sensor is open or short-circuited,
ECM enters fail-safe mode. The en-
gine coolant temperature determined
by the ECM is displayed.

H02S1 (B1)

• The signal voltage of the heated oxygen sensor 1

is displayed.

HO2S2 (B1)

• The signal voltage of the heated oxygen sensor 2

is displayed.

HO2S1 MNTR (B1)

RICH/LEAN

• Display of heated oxygen sensor 1 signal during

air-fuel ratio feedback control:
RICH: means the mixture became “rich”, and
control is being affected toward a leaner mixture.
LEAN: means the mixture became “lean”, and
control is being affected toward a rich mixture.

• After turning ON the ignition switch,

“RICH” is displayed until air-fuel mix-
ture ratio feedback control begins.

• When the air-fuel ratio feedback is

clamped, the value just before the
clamping is displayed continuously.

HO2S2 MNTR(B1)

RICH/LEAN

• Display of heated oxygen sensor 2 signal:

RICH: means the amount of oxygen after three
way catalyst is relatively small.
LEAN: means the amount of oxygen after three
way catalyst is relatively large.

• When the engine is stopped, a certain

value is indicated.

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle

speed signal sent from combination meter is dis-
played.

BATTERY VOLT

• The power supply voltage of ECM is displayed.

ACCEL SEN 1

• The accelerator pedal position sensor signal volt-

age is displayed.

• ACCEL SEN 2 signal is converted by

ECM internally. Thus, it differs from
ECM terminal voltage signal.

ACCEL SEN 2

THRTL SEN 1-B1

• The throttle position sensor signal voltage is dis-

played.

• THRTL SEN 2-B1 signal is converted

by ECM internally. Thus, it differs from
ECM terminal voltage signal.

THRTL SEN 2-B1

START SIGNAL

ON/OFF

• Indicates start signal status [ON/OFF] computed

by the ECM according to the signals of engine
speed and battery voltage.

• After starting the engine, [OFF] is dis-

played regardless of the starter sig-
nal.

CLSD THL POS

ON/OFF

• Indicates idle position [ON/OFF] computed by

ECM according to the accelerator pedal position
sensor signal.

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-721

< FUNCTION DIAGNOSIS >

[MR20DE (WITH EURO-OBD)]

AIR COND SIG

ON/OFF

• Indicates [ON/OFF] condition of the air condition-

er switch as determined by the air conditioner sig-
nal.

P/N POSI SW

ON/OFF

• Indicates [ON/OFF] condition from the park/neu-

tral position (PNP) switch signal.

PW/ST SIGNAL

ON/OFF

• [ON/OFF] condition of the power steering system

(determined by the signal sent from ESP control
unit) is indicated.

LOAD SIGNAL

ON/OFF

• Indicates [ON/OFF] condition from the electrical

load signal.
ON: Rear window defogger switch is ON and/or
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.

IGNITION SW

ON/OFF

• Indicates [ON/OFF] condition from ignition switch

signal.

HEATER FAN SW

ON/OFF

• Indicates [ON/OFF] condition from the heater fan

switch signal.

BRAKE SW

ON/OFF

• Indicates [ON/OFF] condition from the stop lamp

switch signal.

INJ PULSE-B1

msec

• Indicates the actual fuel injection pulse width

compensated by ECM according to the input sig-
nals.

• When the engine is stopped, a certain

computed value is indicated.

IGN TIMING

BTDC

• Indicates the ignition timing computed by ECM

according to the input signals.

• When the engine is stopped, a certain

value is indicated.

PURG VOL C/V

• Indicates the EVAP canister purge volume con-

trol solenoid valve control value computed by the
ECM according to the input signals.

• The opening becomes larger as the value in-

creases.

INT/V TIM (B1)

• Indicates [

CA] of intake camshaft advance an-

gle.

INT/V SOL-B1

• The control value of the intake valve timing con-

trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.

• The advance angle becomes larger as the value

increases.

AIR COND RLY

ON/OFF

• The air conditioner relay control condition (deter-

mined by ECM according to the input signals) is
indicated.

FUEL PUMP RLY

ON/OFF

• Indicates the fuel pump relay control condition

determined by ECM according to the input sig-
nals.

THRTL RELAY

ON/OFF

• Indicates the throttle control motor relay control

condition determined by the ECM according to
the input signals.

COOLING FAN

HI/LOW/OFF

• Indicates the condition of the cooling fan (deter-

mined by ECM according to the input signals).
HI: High speed operation
LOW: Low speed operation
OFF: Stop

HO2S1 HTR (B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen

sensor 1 heater determined by ECM accordining
to the input signals.

HO2S2 HTR (B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen

sensor 2 heater determined by ECM according to
the input signals.

Monitored item

Unit

Description

Remarks

EC-722

< FUNCTION DIAGNOSIS >

[MR20DE (WITH EURO-OBD)]

ON BOARD DIAGNOSTIC (OBD) SYSTEM

NOTE:

VEHICLE SPEED

km/h or mph

• The vehicle speed computed from the vehicle

speed signal sent from TCM is displayed.

IDL A/V LEARN

YET/CMPLT

• Display the condition of Idle Air Volume Learning

YET: Idle air volume learning has not been per-
formed yet.
CMPLT: Idle air volume learning has already
been performed successfully.

02SEN HTR DTY

• Indicates the heated oxygen sensor 1 heater con-

trol value computed by the ECM according to the
input signals.

AC PRESS SEN

• The signal voltage from the refrigerant pressure

sensor is displayed.

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle

speed signal sent from combination meter is dis-
played.

SET VHCL SPD

km/h or mph

• The preset vehicle speed is displayed.

MAIN SW

ON/OFF

• Indicates [ON/OFF] condition from MAIN switch

signal.

CANCEL SW

ON/OFF

• Indicates [ON/OFF] condition from CANCEL

switch signal.

RESUME/ACC SW

ON/OFF

• Indicates [ON/OFF] condition from RESUME/AC-

CELERATE switch signal.

SET SW

ON/OFF

• Indicates [ON/OFF] condition from SET/COAST

switch signal.

BRAKE SW1

ON/OFF

• Indicates [ON/OFF] condition from ASCD brake

switch signal.

BRAKE SW2

ON/OFF

• Indicates [ON/OFF] condition of stop lamp switch

signal.

VHCL SPD CUT

NON/CUT

• Indicates the vehicle cruise condition.

NON: Vehicle speed is maintained at the ASCD
set speed.
CUT: Vehicle speed decreased to excessively
low compared with the ASCD set speed, and
ASCD operation is cut off.

LO SPEED CUT

NON/CUT

• Indicates the vehicle cruise condition.

NON: Vehicle speed is maintained at the ASCD
set speed.
CUT: Vehicle speed decreased to excessively
low, and ASCD operation is cut off.

AT OD MONITOR

ON/OFF

• Indicates [ON/OFF] condition of CVT O/D ac-

cording to the input signal from the TCM.

• For M/T models, always “OFF” is dis-

played.

AT OD CANCEL

ON/OFF

• Indicates [ON/OFF] condition of CVT O/D cancel

request signal.

• For M/T models, always “OFF” is dis-

played.

CRUISE LAMP

ON/OFF

• Indicates [ON/OFF] condition of CRUISE lamp

determined by the ECM according to the input
signals.

SET LAMP

ON/OFF

• Indicates [ON/OFF] condition of SET lamp deter-

mined by the ECM according to the input signals.

Voltage

• Voltage, frequency, duty cycle or pulse width

measured by the probe.

• Only “#” is displayed if item is unable

to be measured.

• Figures with “#”s are temporary ones.

They are the same figures as an actu-
al piece of data which was just previ-
ously measured.

Frequency

msec, Hz or %

DUTY-HI

—

DUTY-LOW

PLS WIDTH-HI

PLS WIDTH-LOW

Monitored item

Unit

Description

Remarks

Content .. 298 299 300 301 ..