Nissan Qashqai (2007-2010). Manual - part 188

P1572 ASCD BRAKE SWITCH

EC-271

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

2.

CHECK ASCD CLUTCH SWITCH-II

1.

Adjust ASCD clutch switch installation. Refer to 

CL-8, "Removal and Installation"

.

2.

Check the continuity between ASCD clutch switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace ASCD clutch switch.

Component Inspection (Stop Lamp Switch)

INFOID:0000000001116269

1.

CHECK STOP LAMP SWITCH-I

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the continuity between stop lamp switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK STOP LAMP SWITCH-II

1.

Adjust stop lamp switch installation. Refer to 

BR-18, "Inspection and Adjustment"

.

2.

Check the continuity between stop lamp switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch.

Terminals

Condition

Continuity

1 and 2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed

Terminals

Condition

Continuity

1 and 2

Brake pedal

Fully released

Not existed

Slightly depressed

Existed

EC-272

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

P1574 ASCD VEHICLE SPEED SENSOR

P1574 ASCD VEHICLE SPEED SENSOR

Description

INFOID:0000000001116270

The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combina-
tion meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD
control. Refer to 

EC-60, "System Description"

 for ASCD functions.

DTC Logic

INFOID:0000000001116271

DTC DETECTION LOGIC

NOTE:
• If DTC P1574 is displayed with DTC U1001, first perform the trouble diagnosis for DTC U1001. Refer

to 

EC-121, "DTC Logic"

.

• If DTC P1574 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer

to 

EC-122, "DTC Logic"

.

• If DTC P1574 is displayed with DTC P0500, first perform the trouble diagnosis for DTC P0500. Refer

to 

EC-209, "DTC Logic"

• If DTC P1574 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer

to 

EC-211, "DTC Logic"

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start engine.

2.

Drive the vehicle at more than 40 km/h (25 MPH).

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.

3.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC-272, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000001116272

1.

CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”

Refer to 

BRC-17, "CONSULT-III Function (ABS)"

.

Is the inspection result normal?

YES

>> GO TO 2.

DTC No.

Trouble diagnosis 

name

DTC detecting condition

Possible cause

P1574

ASCD vehicle speed 
sensor

ECM detects a difference between two vehicle 
speed signals is out of the specified range.

• Harness or connectors

(The CAN communication line is open or 
shorted.)
(Combination meter circuit is open or shorted.)

• Combination meter
• ABS actuator and electric unit (control unit)
• Wheel sensor
• ECM

P1574 ASCD VEHICLE SPEED SENSOR

EC-273

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Repair or replace.

2.

CHECK COMBINATION METER

Check combination meter function.
Refer to 

MWI-23, "CONSULT-III Function (METER/M&A)"

.

>> INSPECTION END

EC-274

< COMPONENT DIAGNOSIS >

[HR16DE (WITH EURO-OBD)]

P1706 PNP SWITCH

P1706 PNP SWITCH

Description

INFOID:0000000001062572

When the shift lever position is in the neutral position, ECM detects the position because the continuity of the
line (the ON signal) exists.

DTC Logic

INFOID:0000000001062573

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

INSPECTION START

Do you have CONSULT-III?
Do you have CONSULT-III?

YES

>> GO TO 2.

NO

>> GO TO 5.

2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.

>> GO TO 3.

3.

CHECK PNP SWITCH FUNCTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “P/N POSI SW” in “DATA MONITOR” mode with CONSULT-III. Then check the “P/N POSI SW” sig-
nal under the following conditions.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Go to 

EC-275, "Diagnosis Procedure"

.

4.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Select “DATA MONITOR” mode with CONSULT-III.

2.

Start engine and warm it up to normal operating temperature.

3.

Maintain the following conditions for at least 50 consecutive seconds.

CAUTION:

Always drive vehicle at a safe speed.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1706

Park/neutral position 
switch

The signal of the park/neutral position (PNP) 
switch is not changed in the process of engine 
starting and driving.

• Harness or connectors

[The park/neutral position (PNP) switch 
circuit is open or shorted.]

• Park/neutral position (PNP) switch

Position (Shift lever)

Known-good signal

Neutral position 

ON

Except above position

OFF

ENG SPEED

 1,925 - 6,375 rpm

COOLAN TEMP/S

More than 70

°

C (158

°

F)

B/FUEL SCHDL

 2.5 - 31.8 msec