Nissan Qashqai (2007-2010). Manual

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.

>> GO TO 2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

PERFORM "BASIC INSPECTION"

Perform the basic inspection.
Refer to

PWC-82, "Basic Inspection"

>> GO TO 4.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.

>> GO TO 5.

IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”

Perform the diagnosis with “Component diagnosis” of the applicable system.

>> GO TO 6.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 7.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.
Is the malfunctioning part repaired or replaced?

YES

>> Trouble diagnosis is completed.

>> GO TO 3.

PWC-4

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000000990478

Initial setting is necessary.
• When the power supply to the power window main switch or power window motor is cut off by the removal

of battery terminal or the battery fuse is blown.

• Disconnection and connection of power window main switch harness connector.
• Removal and installation of motor from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
NOTE:
The following specified operations are not performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special

Repair Requirement"

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000000990479

INITIALIZATION PROCEDURE

Disconnect battery minus terminal or power window main switch connector. Reconnect it after a minute or
more.

Turn ignition switch ON.

Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open)

Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 5 seconds or more.

Inspect anti-pinch function.

CHECK ANTI-PINCH FUNCTION

Fully open the door window.

Place a piece of wood near fully closed position.

Close door glass completely with AUTO-UP.

• Check that glass lowers for approximately 150mm or 2 seconds without pinching piece of wood and stops.
• Check that glass does not rise when operating the power window main switch while lowering.

CAUTION:

• Perform initial setting when auto-up operation or anti-pinch function does not operate normally.
• Check that AUTO-UP operates before inspection when system initialization is performed.
• Do not check with hands and other body parts because they may be pinched. Do not get pinched.
• It may switch to fail-safe mode if open/close operation is performed continuously. Perform initial set-

ting in that situation. Refer to

PWC-71, "Fail Safe"

• Finish initial setting. Otherwise, next operation cannot be done.
1.

Auto-up operation

Anti-pinch function

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000000990480

Refer to

PWC-4, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Descrip-

tion"

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000000990481

Nissan Qashqai (2007-2010). Manual - part 1271