AUTOMOTIVE INDUSTRY RETAIL, SERVICE & REPAIR - part 51

AURT3814A Carry out gas tungsten arc (TIG) welding procedures 

Automotive Industry RS&R 

356 

AUR99 Version 4.00 Review by 30 June 2004 

©Australian National Training Authority 

 

ELEMENT PERFORMANCE 

CRITERIA 

3. 

Clean up work area and 
maintain equipment 
(continued) 

3.5 

Operator maintenance is completed in accordance with 
manufacturer/component supplier specifications and site 
procedures 

3.6 

Tooling is maintained in accordance with workplace 
procedures 

 

RANGE STATEMENT  

The Range Statement provides advice to interpret the scope and context of this unit of 
competency, allowing for differences between enterprises and workplaces. It relates to the unit 
as a whole and facilitates holistic assessment. The following variables may be present for this 
particular unit: 

TIG welding  

•  Equipment to include TIG welders 

•  Material to include Argon gas, filling rods 

Unit scope 

• 

Work involves preparation, selection, measuring of 
material and TIG welding 

Unit context 

•  OH&S requirements include safety management systems, 

hazardous substances and dangerous goods code, safe 
operating procedures and Australian Design Rules  

•  Work is carried out in accordance with legislative 

obligations, environmental legislation, relevant health 
regulations, manual handling and lifting equipment 
procedures and organisation insurance requirements 

•  Work requires individuals to demonstrate discretion, 

judgement and problem solving skills in lifting, safety 
equipment, gas tungsten arc welding procedures, 
environmental issues, repair procedures and vehicle 
operational requirements 

•  Competency may be demonstrated in workplaces involved 

in welding and fabrication, roadside service, dealership, 
panel repairs, accessory fitting, workshops 

Tools and equipment 

• 

Tools and equipment are to include but not be limited to: 

•  Hand tools, TIG welding machines, rods and safety 

equipment 

•  Other resources may include: measuring equipment, 

marking out equipment and lifting equipment 

Material 

• 

Material are to include Argon gas and filling rods 

Personal protective 
equipment 

• 

Personal protective equipment is to include that prescribed 
under legislation, regulations and enterprise policies and 
practices 

Automotive Industry RS&R  

AURT3814A Carry out gas tungsten arc (TIG) welding procedures 

©Australian National Training Authority 

 AUR99 Version 4.00 Review by 30 June 2004 

357 

 

RANGE STATEMENT  

Information and 
procedures 

•  Workplace procedures relating to the use of tools and 

equipment 

•  Work instructions, including: 

•  Job sheets 

•  Vehicle manufacturer/component supplier specifications 

•  Enterprise operating procedures 

•  Component manufacture specifications 

•  Customer requirements 

•  Industry/workplace codes of practice 

• Legislation for vehicle roadworthiness including 

Australian Design Rules 

•  Material safety data sheets 

•  Workplace procedures relating to reporting and 

communication 

•  Manufacturer/component supplier specifications and 

operational procedures 

 

EVIDENCE GUIDE 

The Evidence Guide identifies the critical aspects, knowledge and skills to be demonstrated to 
confirm competency for this unit. This is an integral part of the assessment of competency and 
should be read in conjunction with the Range Statement. 

Critical aspects of 
evidence 

•  Interpret work order and locate and apply relevant 

information 

•  Apply safe handling requirements for equipment, products 

and material, including use of personal protective 
equipment 

•  Read and interpret communication procedural information 

from job sheets to prepare for work 

•  Identify material used in the work process 

•  Follow work instructions, operating procedures and 

inspection processes to: 

•  minimise the risk of injury to self and others 

•  prevent damage and wastage of goods, equipment and 

products 

•  maintain required production output and product quality 

AURT3814A Carry out gas tungsten arc (TIG) welding procedures 

Automotive Industry RS&R 

358 

AUR99 Version 4.00 Review by 30 June 2004 

©Australian National Training Authority 

 

EVIDENCE GUIDE 

Critical aspects of 
evidence (continued) 

•  Identify, set up, operate and maintain TIG welding, safety, 

lifting and measuring equipment 

•  Work effectively with others 

•  Modify activities to cater for variations in workplace 

context and environment 

Underpinning knowledge 

•  The types, characteristics, uses and limitations of: 

•  OH&S requirements 

•  Equipment safety requirements 

•  Personal safety requirements (e.g. toxic fumes/lead 

poisoning) 

•  Types of metals 

•  Types of fluxes, rods and their application 

•  Planning of TIG welding processes and techniques 

•  Equipment maintenance procedures 

•  Workplace safety policies and procedures 

•  Workplace guidelines regarding acceptable tolerance 

levels to be considered as per job sheet and 
manufacturer/component supplier specification. 

•  Procedures for reporting faults and material defects 

Underpinning skills 

These include a number of processes that are learnt throughout work and life, which are 
required in most jobs. Some of these are covered by the national key competencies, although 
others may be added. The questions below highlight how these processes are applied in this 
competency unit. The number in brackets indicates the level to which the key competency 
needs to be demonstrated where (1) is where work is within set conditions and process, (2) is 
where the management or facilitation of conditions or process is exercised, and (3) is where 
the design and/or development of conditions or process is required. 

How will the candidate 
apply the following key 
competency in this unit? 

The candidate will need to: 

Collect, analyse and 
organise information 

 

Collect, organise and understand information related to TIG 
welding work orders, plans and safety procedures. 

 (Level 2)

Automotive Industry RS&R  

AURT3814A Carry out gas tungsten arc (TIG) welding procedures 

©Australian National Training Authority 

 AUR99 Version 4.00 Review by 30 June 2004 

359 

 

EVIDENCE GUIDE 

Underpinning skills (continued) 

Communicate ideas and 
information 

 

Communicate ideas and information to enable confirmation of 
work requirements and specifications, coordination of work with 
site supervisor, other workers and customers, and the reporting 
of work outcomes and problems. 

(Level 2)

Plan and organise 
activities 

 

Plan and organise activities including the preparation and layout 
of the worksite and the obtaining of equipment and material to 
avoid any back tracking, workflow interruptions or wastage. 

(Level 2)

Work with others and in 
a team 

 

Work with others and in a team by recognising dependencies 
and using cooperative approaches to optimise workflow and 
productivity. 

(Level 2)

Use mathematical ideas 
and techniques 

 

Use mathematical ideas and techniques to correctly complete 
measurements and estimate material requirements. 

(Level 2)

Solve problems 

 

Use pre-checking and inspection techniques to anticipate 
planning and scheduling problems, avoid wastage of time and 
material. 

(Level 2)

Use technology 

 

Use the workplace technology related to:  

• 

Access, interpret and apply technical information 

• 

Use relevant tools and equipment 

• 

Apply personal safety requirements 

• 

Apply Gas Tungsten Arc (TIG) welding procedures 

Including tools and equipment.  

(Level 2)

 

AURT3814A Carry out gas tungsten arc (TIG) welding procedures 

Automotive Industry RS&R 

360 

AUR99 Version 4.00 Review by 30 June 2004 

©Australian National Training Authority 

 

EVIDENCE GUIDE 

Resource implications 

• 

Access to vehicle and manufacturer/component supplier 
specifications as identified in the Range Statement, 
standard operating procedures 

Method of assessment 

• 

Assessment methods must confirm consistency of 
performance over time and in a range of workplace 
relevant contexts 

• 

Assessment should be by direct observation of tasks and 
questioning on underpinning knowledge 

• 

Assessment should be conducted over time and may be in 
conjunction with assessment of other units of competency 

Context/s of assessment 

• 

Assessment may occur on the job or in a workplace 
simulated facility with relevant process equipment, 
material, work instructions and deadlines 

 

Automotive Industry RS&R  

AURT3815A Carry out spot welding procedures 

©Australian National Training Authority 

 AUR99 Version 4.00 Review by 30 June 2004 

361 

 

AURT3815A 

Carry out spot welding procedures 

Unit descriptor 

This unit covers the competency to carry out spot welding 
procedures appropriate to the repairs conducted in the retail, 
service and repair streams.  

 

ELEMENT PERFORMANCE 

CRITERIA 

1.  Prepare for work 

1.1 

Work instructions are used to determine job requirements 
including job sheets, quality and quantity of material 

1.2 

Job specifications are read and interpreted 

1.3 

OH&S requirements, including personal protection 
needs, are observed throughout the work 

1.4 

Material for repairs and replacements are selected and 
inspected for quality 

1.5 

Correct hand, power tools and safety equipment for safe 
use 

1.6 

Products are determined to minimise waste material 

1.7 

Procedures are identified for maximising energy 
efficiency whilst completing the job 

2.  Carry out Spot Welding 

procedures 

2.1 

Spot welding procedures are completed without causing 
damage to any component or system 

2.2 

Information is accessed from appropriate sources to 
enable welding to be performed in accordance with 
vehicle and equipment manufacturer/component supplier 
procedures 

2.3 

Spot welding is carried out according to a standard that 
meets industry regulations/guidelines, OH&S 
requirements, legislation and enterprise 
policy/procedures 

3. 

Clean up work area and 
maintain equipment 

3.1 

Material that can be reused is collected and stored 

3.2 

Waste and scrap is removed following workplace procedures

3.3 

Equipment and work area are cleaned and inspected for 
serviceable conditions in accordance with workplace 
procedures 

3.4 

Unserviceable equipment is tagged and faults identified in 
accordance with workplace 

3.5 

Operator maintenance is completed in accordance with 
manufacturer/component supplier specifications and site 
procedures 

3.6 

Tooling is maintained in accordance with workplace 
procedures 

AURT3815A Carry out spot welding procedures 

 

Automotive Industry RS&R 

362 

AUR99 Version 4.00 Review by 30 June 2004 

©Australian National Training Authority 

 

RANGE STATEMENT  

The Range Statement provides advice to interpret the scope and context of this unit of 
competency, allowing for differences between enterprises and workplaces. It relates to the unit 
as a whole and facilitates holistic assessment. The following variables may be present for this 
particular unit: 

Spot welding  

•  Equipment to include spot welders 

•  Material to include steel products 

Unit scope 

• 

Work involves  

Unit context 

•  OH&S requirements include safety management systems, 

hazardous substances and dangerous goods code, safe 
operating procedures and Australian Design Rules 

•  Work is carried out in accordance with legislative 

obligations, environmental legislation, relevant health 
regulations, manual handling and lifting equipment 
procedures and organisation insurance requirements 

•  Work requires individuals to demonstrate discretion, 

judgement and problem solving skills in lifting, safety 
equipment, spot welding procedures, environmental issues, 
repair procedures and vehicle operational requirements 

•  Competency may be demonstrated in workplaces involved 

in welding and fabrication, dealership, panel repairs, 
accessory fitting, workshops 

Tools and equipment 

•  Tools and equipment are to include but not be limited to: 

•  Hand tools, spot welding equipment 

•  Other resources may include: measuring equipment, 

marking out equipment and lifting equipment 

Material 

•  Material are to include steel product 

Personal protective 
equipment 

•  Personal protective equipment is to include that prescribed 

under legislation, regulations and enterprise policies and 
practices 

 

Automotive Industry RS&R  

AURT3815A Carry out spot welding procedures 

©Australian National Training Authority 

 AUR99 Version 4.00 Review by 30 June 2004 

363 

 

RANGE STATEMENT  

Information and 
procedures 

•  Workplace procedures relating to the use of tools and 

equipment 

•  Work instructions, including: 

•  Job sheets 

•  Vehicle manufacturer/component supplier specifications 

•  Enterprise operating procedures 

•  Component manufacture specifications 

•  Customer requirements 

•  Industry/workplace codes of practice 

• Legislation for vehicle roadworthiness including 

Australian Design Rules 

•  Material safety data sheets 

•  Workplace procedures relating to reporting and 

communication 

•  Manufacturer/component supplier specifications and 

operational procedures 

 

EVIDENCE GUIDE 

The Evidence Guide identifies the critical aspects, knowledge and skills to be demonstrated to 
confirm competency for this unit. This is an integral part of the assessment of competency and 
should be read in conjunction with the Range Statement. 

Critical aspects of 
evidence 

•  Interpret work order and locate and apply relevant 

information 

•  Apply safe handling requirements for equipment, products 

and material, including use of personal protective 
equipment 

•  Read and interpret communication procedural information 

from job sheets to prepare for work 

•  Identify material used in the work process