MINI Paceman (2016 year). Instruction

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Safety

Final tire failure

Malfunction

Vibrations or loud noises while driving can indi-

The yellow warning light flashes yellow

cate the final failure of the tire.

and then lights up continuously.

Reduce your speed and stop. Parts of tires can

A Check Control message is displayed.

peel away, which could cause an accident.

A flat tire or tire inflation pressure loss cannot

Do not continue driving. Contact a dealer’s

be detected.

service center or another qualified service cen-

ter or repair shop.

Examples and recommendations in the follow-

ing situations:

Message indicating that the inflation

▷ A wheel without TPM electronics is

pressure needs to be checked

mounted.

The yellow warning light lights up.

Have it checked by a dealer’s service center

or another qualified service center or repair

A Check Control message is displayed.

shop as needed.

▷ The system has detected that a wheel was

▷ Malfunction:

changed but a reset was not performed.

Have system checked by a dealer’s service

▷ The tire was not inflated according to speci-

center or another qualified service center or

fications.

repair shop.

▷ The tire pressure has dropped since the last

The yellow warning light flashes and

confirmation.

then lights up continuously.

In this case:

A Check Control message is displayed.

▷ Check the tire inflation pressure and correct

it if necessary.

A flat tire or tire inflation pressure loss cannot

be detected.

▷ After changing a wheel, reset the system.

Display in the following situation:

System limits

▷ Disturbance by other systems or devices

The system will not function properly if a reset

with the same radio frequency:

was not performed, e.g., it may identify a tire as

After leaving the area of the disturbance,

flat although the tire is filled to the correct infla-

the system automatically becomes active

tion pressure.

again.

The tire pressure depends on the temperature

of the tire. An increase in the tire temperature,

Declaration according to NHTSA/FMVSS

e.g., while driving or due to sunlight, increases

138 Tire Pressure Monitoring Systems

the tire inflation pressure. The tire pressure de-

Each tire, including the spare (if provided)

creases when the tire temperature drops. In

should be checked monthly when cold and in-

case of severe temperature drops, this behavior

flated to the inflation pressure recommended

may lead to a warning on account of the de-

by the vehicle manufacturer on the vehicle

fined warning limits.

placard or tire inflation pressure label (If your

The system cannot indicate sudden serious tire

vehicle has tires of a different size than the size

damage caused by external circumstances.

indicated on the vehicle placard or tire inflation

pressure label, you should determine the

proper tire inflation pressure for those tires.).

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Safety

CONTROLS

As an added safety feature, your vehicle has

been equipped with a tire pressure monitoring

system (TPMS) that illuminates a low tire pres-

sure telltale when one or more of your tires is

significantly under-inflated. Accordingly, when

the low tire pressure telltale illuminates, you

should stop and check your tires as soon as

possible, and inflate them to the proper pres-

sure. Driving on a significantly under-inflated

tire causes the tire to overheat and can lead to

tire failure. Under-inflation also reduces fuel ef-

ficiency and tire tread life, and may affect the

vehicle's handling and stopping ability.

Please note that the TPMS is not a substitute for

proper tire maintenance, and it is the driver's

responsibility to maintain correct tire pressure,

even if under-inflation has not reached the

level to trigger illumination of the TPMS low tire

pressure telltale.

Your vehicle has also been equipped with a

TPMS malfunction indicator to indicate when

the system is not operating properly. The TPMS

malfunction indicator is combined with the low

tire pressure telltale. When the system detects

a malfunction, the telltale will flash for approxi-

mately one minute and then remain continu-

ously illuminated. This sequence will continue

upon subsequent vehicle startups as long as

the malfunction exists. When the malfunction

indicator is illuminated, the system may not be

able to detect or signal low tire pressure as in-

tended. TPMS malfunctions may occur for a va-

riety of reasons, including the installation of re-

placement or alternate tires or wheels on the

vehicle that prevent the TPMS from functioning

properly. Always check the TPMS malfunction

telltale after replacing one or more tires or

wheels on your vehicle to ensure that the re-

placement or alternate tires and wheels allow

the TPMS to continue to function properly.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Driving stability control systems

possible. This system utilizes all of the benefits

Vehicle features and op-

provided by ABS.

tions

Do not reduce the pressure on the brake pedal

This chapter describes all standard, country-

for the duration of full braking.

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

Dynamic Stability Con-

the selected options or country versions. This

trol DSC

also applies to safety-related functions and sys-

tems.

The concept

When using the features and systems described

DSC prevents traction loss in the driving wheels

here, adhere to local regulations.

when driving away and accelerating.

DSC also recognizes unstable vehicle condi-

tions, such as fishtailing or nose-diving. Subject

Antilock Brake System

to physical limits, DSC helps to keep the vehicle

ABS

on a steady course by reducing engine speed

and by applying brakes to the individual

ABS prevents locking of the wheels during

wheels.

braking.

Adapt your driving style to the situation, for an

Steerability is maintained even during full brak-

appropriate driving style is always the responsi-

ing. This increases active driving safety.

bility of the driver.

ABS is operational every time you start the en-

DSC is operational every time you start the en-

gine.

Electronic brake-force distribution EBV

WARNING

The system controls the brake pressure in the

When driving with roof load, e.g. with

rear wheels to ensure stable braking behavior.

roof-mounted luggage rack, driving safety may

not be ensured in driving-critical situations due

CBC Cornering Brake Control

to the elevated center of gravity. There is risk of

When braking in curves or during a lane

accidents or risk of property damage. Do not

change, driving stability and steering response

deactivate Dynamic Stability Control DSC when

are improved further.

driving with roof load.◀

Brake assistant

When the brakes are applied rapidly, this sys-

tem automatically produces the maximum

braking force boost. In this way, the system

helps keep the braking distance as short as

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving stability control systems

CONTROLS

Deactivating DSC

DSC and DTC deactivated.

Press the switch until the DSC OFF indicator

lamp lights up in the speedometer and DSC OFF

appears in the tachometer. DSC is deactivated.

Dynamic Traction Con-

Intervening measures to stabilize the vehicle

trol DTC

and give it forward momentum are no longer

executed.

The concept

When driving with snow chains or to rock the

The DTC system is a version of the DSC in which

vehicle free of snow, it may be useful to deacti-

forward momentum is optimized.

vate DSC temporarily.

The system ensures maximum forward mo-

To increase vehicle stability, activate DSC again

mentum on special road conditions, e.g., unp-

as soon as possible.

lowed snowy roads, but driving stability is lim-

ited.

Activating DSC

It is therefore necessary to drive with appropri-

Press the switch again; the DSC indicator lamps

ate caution.

in the display elements go out.

You may find it useful to briefly activate DTC

under the following special circumstances:

Indicator/warning lights

▷ When driving in sand, on snowy inclines, in

The indicator lamp in the tachometer

slush, or on unplowed, snow-covered road

flashes: DSC is controlling the drive

surfaces.

forces and brake forces.

▷ When rocking a vehicle free or starting off

The indicator lamp lights up: DSC and DTC has

in deep snow, sand, or on loose ground.

failed.

▷ When driving with snow chains.

The indicator lamp in the speedometer

lights up and DSC OFF appears in the

tachometer.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Driving stability control systems

Activating DTC

DTC is activated.

Press the switch; the DSC OFF indicator lamp

lights up in the speedometer and TRACTION

appears in the tachometer. Dynamic Stability

Hill drive-off assistant

Control DSC is deactivated, Dynamic Traction

Control DTC is activated.

This system supports driving away on gradients.

The parking brake is not required.

Deactivating DTC

1. Hold the vehicle in place with the foot

brake.

Press the switch again; the DSC OFF indicator

lamp in the speedometer and TRACTION in the

2. Release the foot brake and drive away

tachometer go out.

without delay.

In the interest of better forward momentum,

After the foot brake is released, the vehicle is

brake intervention is performed in the manner

held in place for approx. 2 seconds.

of a differential lock when the drive wheels spin

unevenly even when DSC/DTC is deactivated.

ALL4 all-wheel system

Indicator/warning lights

ALL4 is the all-wheel system of your MINI. The

The indicator lamp in the tachometer

combined effects of ALL4 and DSC further opti-

flashes: DTC is controlling the drive

mize the traction and dynamic driving charac-

forces and brake forces.

teristics. The ALL4 all-wheel system variably

The indicator lamp lights up: DSC and DTC has

distributes the drive forces to the front and rear

failed.

axles depending on the driving situation and

prevailing road conditions.

The indicator lamp in the speedometer

lights up and TRACTION appears in the

tachometer.

Sport button

When this button is pressed, the vehicle re-

sponds in an even sportier manner.

▷ The engine responds more spontaneously

to accelerator movements.

▷ The steering responds more directly.

▷ Cooper S, John Cooper Works: the engine

sounds sportier when coasting.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Driving comfort

Controls

Vehicle features and op-

tions

Overview

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your car, e. g., due to

the selected options or country versions. This

also applies to safety-related functions and sys-

tems.

When using the features and systems described

here, adhere to local regulations.

Maintaining, storing, and increasing the

speed

Cruise control

Activating/deactivating cruise control

Maintaining, storing, and reducing the

The concept

speed

The system is functional at speeds beginning at

Resuming cruise control

approx. 20 mph/30 km/h.

The vehicle stores and maintains the speed

Switching on

specified using the controls on the steering

wheel.

Press button 2.

WARNING

The indicator lamp lights up in the

speedometer. Cruise control is ready to

The use of the system can lead to an in-

operate and can be activated.

creased risk of accidents in the following situa-

tions:

▷ On winding roads.

Switch off

▷ In heavy traffic.

WARNING

▷ On slippery roads, in fog, snow or rain, or

The system does not relieve from the per-

on a loose road surface.

sonal responsibility to correctly assess the traf-

fic situation. Based on the limits of the system,

There is risk of accidents or risk of property

it cannot independently react to all traffic situa-

damage. Only use the system if driving at con-

tions. There is risk of an accident. Adjust the

stant speed is possible.◀

driving style to the traffic conditions. Watch

traffic closely and actively interfere in the re-

spective situations.◀

Press button 2.

▷ When activated: press twice.

▷ When interrupted: press once.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving comfort

CONTROLS

The displays go out. The stored target speed is

Decreasing speed

cleared.

Press button 3 repeatedly or hold it until the

desired speed is reached.

Interrupting

The functions are the same those when the

Press button 2.

speed is increased, only that the speed is re-

The system is interrupted automatically if

duced.

▷ The brakes are applied.

Resuming a speed stored beforehand

▷ The clutch pedal is depressed.

Press button 4.

▷ The transmission position D is disengaged.

The last stored speed is resumed and main-

▷ DSC intervenes.

tained.

The stored speed is cleared when the ignition is

Maintaining, storing the current speed

switched off.

WARNING

The desired speed can be incorrectly ad-

Display in the tachometer

justed or called up by mistake. There is risk of

an accident. Adjust the desired speed to the

traffic conditions. Watch traffic closely and ac-

tively interfere in the respective situations.◀

Press button 1 or button 3.

The current speed is maintained and stored. It

is displayed briefly in the tachometer.

On downhill gradients, it may prove impossible

to maintain the set speed if the engine braking

The selected speed is displayed briefly.

power is insufficient. On uphill gradients, it may

prove impossible to maintain the set speed if

If the display --- mph or --- km/h appears

the engine power output is insufficient.

briefly, conditions may not be adequate to op-

erate the system.

Increasing speed

▷ Press button 1 repeatedly until the desired

For better control

speed is reached.

The indicator lamp lights up in the

Each time the button is pressed, the speed

speedometer. Cruise control is ready to

increases by approx. 1 mph/1 km/h.

operate and can be activated.

▷ Press and hold button 1 until the desired

speed is reached.

Malfunction

The vehicle accelerates without pressure on

The warning lamp in the tachometer

the accelerator pedal. After the button is

lights up.

released, the achieved speed is maintained

and stored.

The system is malfunctioning or has

failed.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Driving comfort

System limits

Park Distance Control

WARNING

PDC

The system does not relieve from the per-

The concept

sonal responsibility to correctly assess the traf-

fic situation. There is risk of an accident. Adjust

PDC provides support when parking in reverse.

the driving style to the traffic conditions. Watch

Signal tones indicate that the vehicle is ap-

traffic and vehicle surroundings closely and ac-

proaching an object behind it. Measurements

tively interfere in the respective situations.◀

are made by four ultrasound sensors in the

bumpers.

Malfunction

The range of these sensors is approx. 6 ft/2 m.

An acoustic warning is first given:

The warning light lights up. PDC is mal-

functioning or has failed. Have the sys-

▷ By the two corner sensors at ap-

tem checked.

prox. 24 in/60 cm.

▷ By the rear middle sensors at approx.

To ensure full functionality of the sensors, keep

5 ft/1.50 m.

the sensors clean and free of ice. When using

high-pressure washers, do not spray the sen-

WARNING

sors for long periods and maintain a distance of

Due to high speeds when PDC is acti-

at least 12 in/30 cm.

vated, the warning can be delayed due to phys-

ical circumstances. There is risk of injuries or

risk of property damage. Avoid approaching an

object quickly. Avoid driving away quickly while

PDC is not yet active.◀

Automatic operation

The system is activated after approx. one sec-

ond when reverse gear or selector lever posi-

tion R is engaged while the engine is running or

the ignition is switched on. Await this short pe-

riod before setting the vehicle into motion.

Signal tones

The closer the vehicle is to the object, the

shorter the intervals become. If the distance to

a detected object is less than approx.

12 in/30 cm, a continuous tone is sounded.

If the distance remains constant, for example

when driving parallel to a wall, the signal tone

is stopped after approx. 3 seconds.

Volume

The signal tone volume can be adjusted.

Radio MINI Boost CD, refer to page 126.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Climate

CONTROLS

Climate

necessarily available in your car, e. g., due to

Vehicle features and op-

the selected options or country versions. This

tions

also applies to safety-related functions and sys-

tems.

This chapter describes all standard, country-

specific and optional features offered with the

When using the features and systems described

series. It also describes features that are not

here, adhere to local regulations.

Air conditioner

Air volume

Rear window defroster

Cooling function

Vent settings

Recirculated air mode

Windshield heating

Temperature

Air volume

The air flow rate may be reduced or the blower

may be switched off entirely to save on battery

Vary the air volume. The higher

power.

the rate, the more effective the

heating or cooling will be.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Climate

Switching the system on/off

Temperature

Turn the rotary switch for the air volume to 0.

Turn upward, red, to raise the

The blower and air conditioner are completely

temperature.

switched off and the air supply is cut off.

Turn downward, blue, to lower

Set any air volume to switch on the air condi-

the temperature.

tioning.

Cooling function

Rear window defroster

The car's interior can only be

The rear window defroster

cooled with the engine running.

switches off automatically after a

certain period of time.

The cooling function cools and

dehumidifies the incoming air

The rear window defroster

before reheating it as required,

power may be lowered or even

according to the temperature setting.

switched off entirely to save on battery power.

The cooling function helps to prevent conden-

sation on the windows or to remove it quickly.

Vent settings

Depending on the weather, the windshield may

Direct the flow of air to the win-

fog up briefly when the engine is started.

dows

, to the upper body

area

, or to the footwell

To cool the air faster and more intensively

Intermediate positions are possi-

when external temperatures are high, switch

ble.

on the recirculated air mode.

Recirculated air mode

Windshield heating

If the air outside the car has an

The windshield heating switches

unpleasant odor or contains pol-

off automatically after some

lutants, shut off the supply to the

time.

interior of the car temporarily.

The windshield heating may be

The system then recirculates the

reduced or even switched off en-

air currently within the vehicle.

tirely to save on battery power.

Should the windows fog up in the recirculated-

air mode, press the AUTO button or switch off

Defrosting and defogging windows

the recirculated-air mode and increase the air

1. Set the maximum air volume.

volume if necessary. Make sure that air can

2. Air distribution in position

flow to the windshield.

By switching on the cooling function, the

Recirculated air mode is automatically deacti-

windows are defogged more rapidly.

vated at low external temperatures.

3. Set the highest temperature, red.

With constant recirculated-air mode, the air

quality in the car's interior deteriorates and the

4. Deactivate recirculated air mode.

fogging of the windows increases.

5. Switch on the windshield heating if neces-

sary.

6. Switch on the rear window defroster if nec-

essary.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Climate

CONTROLS

Microfilter

tion by filtering gaseous pollutants from the

outside air. The combined filter should be

The microfilter traps dust and pollen. The mi-

changed during maintenance of your vehicle.

crofilter should be changed during mainte-

nance of your vehicle.

Microfilter/activated-charcoal filter

The microfilter traps dust and pollen. The acti-

vated-charcoal filter provides additional protec-

Automatic climate control

Air flow, instruction

Defrosting windows and removing conden-

sation

AUTO program

Cooling function

Recirculated air mode

Rear window defroster

Maximum cooling

10 Windshield heating

Instruction air distribution

Temperature

Comfortable interior climate

The following sections contain more detailed

information on the available setting options.

The AUTO program offers the optimum air dis-

tribution and air volume for virtually all condi-

Most of these settings are stored for the remote

tions, refer to AUTO program below. Select a

control in use, Personal Profile settings, refer to

comfortable interior temperature only.

page 21.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Climate

Air flow, instruction

the recirculated-air mode and increase the air

volume if necessary. Make sure that air can

Press the - button to reduce the

flow to the windshield.

air volume. Press the + button to

increase the air volume.

Recirculated air mode is automatically deacti-

vated at low external temperatures.

The automatic mode for the air

volume can be switched on

With constant recirculated-air mode, the air

again using the AUTO button.

quality in the car's interior deteriorates and the

fogging of the windows increases.

The air flow rate may be reduced or the blower

may be switched off entirely to save on battery

Maximum cooling

power. The display remains the same.

Automatic climate control

switches to the lowest tempera-

Switching the system on/off

ture, a high air volume, and re-

Reduce the air volume by pressing the - button

circulated air mode.

until the system is switched off. All displays go

For maximum cooling, open the

out.

vents for the upper body area.

Press the AUTO button to switch the automatic

climate control back on.

The air is cooled as quickly as possible:

▷ At an external temperature above

AUTO program

32 ℉/0 ℃.

The AUTO program automati-

▷ When the engine is running.

cally adjusts the air distribution

to the windshield and side win-

Instruction air distribution

dows, toward the upper body

The flow of air is directed, as se-

area, and into the footwell. The

lected, to the windows, to the

air volume and your specifications for the tem-

upper body area, or to the foot-

perature are adjusted to outside influences due

well.

to the seasons, e. g., solar radiation.

The automatic mode for the air

The cooling function is switched on automati-

distribution can be switched back on using the

cally with the AUTO program.

AUTO button.

The program is switched off if the air distribu-

tion is instructionly adjusted or the button is

pressed again.

Temperature

Set the desired temperature in-

dividually.

Recirculated air mode

The automatic climate control

If the air outside the car has an

achieves this temperature as

unpleasant odor or contains pol-

quickly as possible regardless of

lutants, shut off the supply to the

the season, using maximum cooling or heating

interior of the car temporarily.

power if necessary, and then maintains it.

The system then recirculates the

air currently within the vehicle.

When switching between different temperature

settings in rapid succession, the automatic cli-

Should the windows fog up in the recirculated-

air mode, press the AUTO button or switch off

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Climate

CONTROLS

mate control does not have sufficient time to

The cooling function is switched on automati-

adjust the set temperature.

cally when the AUTO button is pressed.

Rear window defroster

Microfilter/activated-charcoal filter

The rear window defroster

The microfilter traps dust and pollen. The acti-

switches off automatically after a

vated-charcoal filter provides additional protec-

certain period of time.

tion by filtering gaseous pollutants from the

outside air. The combined filter should be

changed during maintenance of your vehicle.

Depending on the vehicle equipment, upper

wires are used as an antenna and are not part

of the rear window defroster.

Ventilation

Defrosting and defogging windows

Quickly removes ice and con-

densation from the windshield

and front side windows. For this

purpose, also switch on the cool-

ing function.

The windshield heating switches on automati-

cally.

Knob for continuous opening and closing

Windshield heating

Nozzle for direction of air flow

The windshield heating switches

off automatically after some

Opening/closing

time.

Turn the knob.

Direction of air flow

Pivot the entire nozzle.

Cooling function

The cooling function cools and

dehumidifies the incoming air

before reheating it as required,

according to the temperature

setting. The car's interior can

only be cooled with the engine running.

The cooling function helps to prevent conden-

sation on the windows or to remove it quickly.

Depending on the weather, the windshield may

fog up briefly when the engine is started. Recir-

culated air mode is switched on automatically if

necessary.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Interior equipment

Compatibility

Vehicle features and op-

If this symbol is printed on the packag-

tions

ing or in the operating instructions of

This chapter describes all standard, country-

the system being operated, the system

specific and optional features offered with the

is generally compatible with the universal ga-

series. It also describes features that are not

rage door opener.

necessarily available in your car, e. g., due to

If you have any questions, please contact:

the selected options or country versions. This

▷ A dealer’s service center or another quali-

also applies to safety-related functions and sys-

fied service center or repair shop.

tems.

▷ www.homelink.com on the Internet.

When using the features and systems described

here, adhere to local regulations.

HomeLink is a registered trademark of the

Gentex Corporation.

Universal garage door

Controls on the interior rearview mirror

opener

The concept

The universal garage door opener can be used

to operate up to 3 functions in remote-control-

led systems, such as garage door drives or

lighting systems. The universal garage door

opener replaces up to 3 different hand-held

transmitters. To operate it, the buttons on the

interior rearview mirror must be programmed

LED

for the desired functions. The hand-held trans-

Buttons

mitter for the system is needed for the pro-

Hand-held transmitter, required for pro-

gramming procedure.

gramming.

WARNING

Body parts can be jammed when operat-

Programming

ing remote-controlled systems, e.g. the garage

door, using the universal garage door opener.

General information

There is risk of injuries or risk of property dam-

1. Switch on the ignition.

age. Make sure that the area of movement of

the respective system is clear during program-

2. Initial setup:

ming and operation. Also follow the safety in-

Press the right and left buttons on the inte-

structions of the hand-held transmitter.◀

rior rearview mirror simultaneously for ap-

prox. 20 seconds until the LED on the inte-

Before selling the vehicle, delete the stored

rior rearview mirror begins to flash. All

functions for security reasons.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Interior equipment

CONTROLS

programmed settings of the buttons on the

In systems with an alternating-code system, the

interior rearview mirror are deleted.

universal garage door opener and the system

must be additionally synchronized.

Hold the hand-held transmitter of the sys-

tem to be operated a distance of approx. 1

Please obtain additional information on syn-

to 3 in/2.5 to 8 cm away from the buttons

chronization in the operating instructions of the

on the interior rearview mirror. The re-

system being set up.

quired distance depends on the particular

The systems will be easier to synchronize with

hand-held transmitter.

the aid of a second person.

Press the button of the desired function on

Synchronization:

the hand-held transmitter and the button

being programmed on the interior rearview

1. Park the vehicle within range of the re-

mirror simultaneously and hold. The LED on

mote-controlled system.

the interior rearview mirror flashes slowly at

2. Program the corresponding button on the

first.

interior rearview mirror as described.

When the LED flashes more rapidly, release

3. Identify and press the synchronization but-

both buttons. Rapid flashing indicates that

ton on the system being set up. You have

the button on the interior rearview mirror

approx. 30 seconds for the next step.

has been programmed.

4. Press and hold the button on the interior

If the LED does not flash faster after 60 sec-

rearview mirror for approx. 3 seconds and

onds, change the distance between the in-

then release it. Repeat this step up to three

terior rearview mirror and the hand-held

times if necessary to complete the synchro-

transmitter and repeat the step. Multiple

nization procedure. When synchronization

trials at different distances may be neces-

is completed, the programmed function is

sary. Wait at least 15 seconds between tri-

executed.

als.

To program additional functions on other

Reprogramming individual buttons

buttons, repeat steps 3 to 5.

1. Switch on the ignition.

The systems can be operated with the buttons

2. Hold the hand-held transmitter at a dis-

on the interior rearview mirror.

tance of approx. 1 to 3 in/2.5 to 8 cm from

the memory buttons.

Special characteristics of alternating-

The required distance depends on the par-

code radio systems

ticular hand-held transmitter.

If the system cannot be operated after re-

3. Press the memory button of the universal

peated programming, check whether the sys-

garage door opener.

tem to be operated uses an alternating-code

4. If the LED flashes slowly after approx.

system.

20 seconds, press the transmit button on

Read the operating instructions of the system

the hand-held transmitter.

or press and hold the programmed button on

5. Release both buttons when the LED flashes

the interior rearview mirror. If the LED on the

rapidly.

interior rearview mirror flashes rapidly at first

and then lights up continuously for 2 seconds,

If the LED does not flash rapidly after ap-

the system is equipped with an alternating-

prox. 60 seconds, change the distance and

code system. This flashing LED pattern repeats

repeat the step.

itself for approx. 20 seconds.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

CONTROLS

Interior equipment

Canada: if the LED does not flash rapidly af-

Folding up

ter approx. 60 seconds, change the dis-

Fold the sun visor up.

tance and repeat the step. If programming

was aborted by the hand-held transmitter,

Glare protection from the side

hold down the memory button and press

and release the button on the hand-held

Folding down

transmitter several times for 2 seconds.

1. Fold the sun visor down.

2. Detach from the holder and pivot sideways

Controls

to the side window.

WARNING

Body parts can be jammed when operat-

Folding up

ing remote-controlled systems, e.g. the garage

To close the sun visor, proceed in reverse order.

door, using the universal garage door opener.

There is risk of injuries or risk of property dam-

Vanity mirror

age. Make sure that the area of movement of

A vanity mirror is located behind a cover on

the respective system is clear during program-

each sun visor.

ming and operation. Also follow the safety in-

structions of the hand-held transmitter.◀

To open, fold the cover up.

Depending on the vehicle equipment, mirror

The system, such as the garage door, can be

lighting comes on when the cover is opened.

operated using the button on the interior rear-

view mirror with the engine running or the igni-

tion switched on. When you are within the re-

ception range of the system, press and hold the

Digital compass

button until the function is initiated. The LED on

the interior rearview mirror lights up continu-

ously while the radio signal is being transmit-

ted.

Deleting stored functions

Press the right and left buttons on the interior

rearview mirror simultaneously for approx.

20 seconds until the LED flashes rapidly. All

stored functions are deleted. The functions can-

Adjustment button on the back of the mir-

not be deleted individually.

ror

Display

Sun visor

The display shows the main or secondary com-

pass direction in which the vehicle is traveling.

Glare protection

Operating concept

Folding down

Various functions can be called up by pressing

Fold the sun visor down.

the adjustment button with a pointed object

such as a pen. The following adjustment op-

tions are displayed one after the other, de-

MINI Paceman (2016 year). Instruction - part 5