Snowmobile Lynx UTILITY E-TEC SERIES. OPERATOR’S GUIDE (2024)

MAINTENANCE SCHEDULE

Maintenance is very important to keep your vehicle in safe operating

condition. The vehicle should be serviced as per the maintenance

schedule.

Proper maintenance is the owner’s responsibility. A warranty claim

may be denied if, among other things, the owner or operator caused

the problem through improper maintenance or use.

Perform periodic checks and follow the maintenance schedule. The

maintenance schedule does not exempt the pre-ride inspection.

WARNING

Failure to properly maintain the vehicle according to the main-

tenance schedule and procedures can make it unsafe to

operate.

EPA Regullatiion - Canadiian and USA Vehiiclles

A repair shop or person of the owner''s choosing may maintain,

replace, or repair emission control devices and systems. These in-

structions do not require components or service by BRP or authorized

BRP snowmobile dealers.

Although an authorized BRP snowmobile dealer has an in-depth tech-

nical knowledge and tools to service your vehicle, the emission-related

warranty is not conditioned on the use of an authorized BRP snowmo-

bile dealer or any other establishment with which BRP has a commer-

cial relationship.

Proper maintenance is the owner’s responsibility. A warranty claim

may be denied if, among other things, the owner or operator caused

the problem through improper maintenance or use.

For emission-related warranty claims, BRP is limiting the diagnosis

and repair of emission-related parts to the authorized BRP snowmo-

bile dealers. For more information, please refer to the US EPA Emis-

sions PERFORMANCE WARRANTY contained in the warranty

section.

You must follow the instructions for fuel requirements in the fueling

section of this manual. Even if gasoline containing greater than ten

volume percent ethanol is readily available, the US EPA issued a pro-

hibition against the use of gasoline containing greater than 10 vol %

ethanol that applies to this vehicle. The use of gasoline containing

greater than 10 vol% ethanol with this engine may harm the emission

control system.

150

MAINTENANCE SCHEDULE

Deep Snow/ Traiil/ Crossover/ Utiiliity Usage

Whether your vehicle is a Deep Snow, Trail, Crossover, or Utility mod-

el, these types of usage require maintenance tasks to be performed

between the regular yearly intervals. These are identified as A+ in the

chart below.

If you regularly ride deep snow and perform frequent hill climbs,

follow the A+ Deep Snow interval and perform the tasks outlined in the

chart below.

If you regularly ride in trails, explore the countryside, or work with

your snowmobile, follow the A+ Trail / Crossover / Utility interval and

perform the tasks outlined in the chart below.

151

MAINTENANCE SCHEDULE

Maiintenance Schedulle

Make sure to perform proper maintenance at recommended intervals

as indicated in the tables.

The maintenance chart indicates the items needing to be addressed

based on 2 criteria, whichever happens first:

- Calendar time

- Odometer reading.

Your driving habits determines the factors you shall adhere too. For

example:

- Someone who uses their vehicle every weekend trail riding would

most likely follow the odometer reading to determine the fre-

quency of his maintenance.

- Someone who uses their vehicle seldomly over the year or only on

a few occasions would follow the calendar time to determine the

frequency of his maintenance.

IMPORTANT: The following tables show the appropriate mainte-

nance application for the first 2 years. For subsequent years, repeat

the same pattern alternatively.

Maiintenance Overviiew

Calendar

Trail/ Cross

Odometer

Time

Over/ Utility

Every

1500 km (1000 mi)

A+

Month

1 Year

3000 km (2000 mi)

Every

4500 km (3000 mi)

A+

Month

2 Years

6000 km (4000 mi)

A and B

152

MAINTENANCE SCHEDULE

E-TEC Engine (except turbo)

TRAIL /

CROSSOVER

A+

/ UTILITY

Every

Every 2

A=Adjust

Every

month

years

C=Clean

year

I=Inspect

1500

6000

L=Lubricate

3000 km

R=Replace

(2000

(1000

(4000

T=Torque

mi)

Air and Fuel Delivery

Fuel components (fuel

cap, hoses, clamps and

tank fixation) and

function

In-line fuel filter

Every 5

years

Body and Chassis

Body panels and

I, T

hardware

Pivots, latches, hinges

and key barrels

Engine and Cooling

Engine cooling

components (coolant

concentration, coolant

I, A

level, hose condition,

clamps, leaks)

Engine rubber mounts

Rewind starter (manual

C, L

start models)

Spark plugs

153

MAINTENANCE SCHEDULE

TRAIL /

CROSSOVER

A+

/ UTILITY

Every

Every 2

A=Adjust

Every

month

years

C=Clean

year

I=Inspect

1500

6000

L=Lubricate

3000 km

R=Replace

(2000

(1000

(4000

T=Torque

mi)

Exhaust manifold

Brake

Brake components and

I, L

function

Brake fluid

Every 2

years

Drive

Chaincase drive chain

tension

Gearbox / chaincase oil

level

Track alignment and

I, A

tension

Gearbox / chaincase oil

Continuously Variable Transmission (CVT)

CVT components and

I, C, L

function

CVT drive belt condition

CVT drive belt tension

Drive pulley retaining

screw

Electrical

155

MAINTENANCE SCHEDULE

TRAIL /

CROSSOVER

A+

/ UTILITY

Every

Every 2

A=Adjust

Every

month

years

C=Clean

year

I=Inspect

1500

6000

L=Lubricate

3000 km

R=Replace

(2000

(1000

(4000

T=Torque

mi)

Battery connections and

condition

Electrical harness

routing

Headlight aim

Modules and applicable

software updates

Operation of control

switches and lighting

Steering and Controls

Ski runners

Gearbox position lever

I, A

operation

Steering alignment

I, A

Steering components

and function

Throttle cable

Throttle operation

Suspension

Suspension components

I, L

and function

Rear suspension limiter

strap

156

MAINTENANCE SCHEDULE

DEEP SNOW

A+

Every 2

A=Adjust

Every

years

C=Clean

month

year

I=Inspect

6000

L=Lubricate

1500 km

3000 km

R=Replace

(1000

(2000

(4000

T=Torque

mi)

Air and Fuel Delivery

Fuel components (fuel

cap, hoses, clamps and

tank fixation) and

function

In-line fuel filter

Every 5

years

Body and Chassis

Body panels and

I, T

hardware

Pivots, latches, hinges

and key barrels

Engine and Cooling

Engine cooling

components (coolant

concentration, coolant

I, A

level, hose condition,

clamps, leaks)

Engine rubber mounts

Rewind starter (manual

C, L

start models)

Every 3

years

Spark plugs

10 000

158

MAINTENANCE SCHEDULE

DEEP SNOW

A+

Every 2

A=Adjust

Every

years

C=Clean

month

year

I=Inspect

6000

L=Lubricate

1500 km

3000 km

R=Replace

(1000

(2000

(4000

T=Torque

mi)

1500 km

(1000

mi)

Gearbox / chaincase oil

Continuously Variable Transmission (CVT)

CVT components and

C, L

function

CVT drive belt condition

CVT drive belt tension

Drive pulley retaining

screw

Electrical

Battery connections and

condition

Electrical harness

routing

Headlight aim

Modules and applicable

software updates

Operation of control

switches and lighting

Steering and Controls

Ski runners

Gearbox position lever

I, A

operation

161

MAINTENANCE PROCEDURES

This section includes instructions for basic maintenance procedures.

WARNING

Turn off the engine, remove tether cord cap and follow these

maintenance procedures when performing maintenance. If you

do not follow proper maintenance procedures you can be in-

jured by hot parts, moving parts, electricity, chemicals or other

hazards.

WARNING

Should removal of a locking device be required (e.g. lock tabs,

self-locking fasteners, etc.) when undergoing disassembly/as-

sembly, always replace with a new one.

Engine Coollant

WARNING

Never open coolant tank cap when engine is hot.

Verifying the Engine Coolant Level

1. Remove access panel.

2. Check coolant level at room temperature. Liquid should touch the

flat surface of the eyesight.

163

MAINTENANCE PROCEDURES

Recommended Engine Coolant

RECOMMENDED COOLANT

XPS Extended life pre-mixed coolant

IF THE RECOMMENDED XPS COOLANT IS NOT

AVAILABLE

Distilled water and antifreeze solution (50% distilled water, 50%

antifreeze)

NOTICE

Always use ethylene-glycol antifreeze containing corrosion in-

hibitors specifically for internal combustion aluminum engines.

Exhaust System

Exhaust System Verification

The muffler tail pipe should be centered with the exit hole in the bottom

pan. Exhaust system must be free of rust or leaks. Make sure that all

parts are securely in place.

Check retaining springs and heat shields condition and replace if

necessary.

The exhaust system is designed to reduce noise and to improve the

total performance of the engine. Modification may be in violation of lo-

cal laws.

NOTICE

If any exhaust system component is removed, modified or dam-

aged, severe engine damage may result.

Spark Pllugs

Spark plugs inspection or replacement may be performed by an au-

thorized BRP snowmobile dealer, repair shop, or person of your own

choosing. Spark plugs inspection or replacement requires an in-depth

technical knowledge. Though not required, it is recommended that an

authorized BRP snowmobile dealer performs spark plugs inspection

or replacement.

166

MAINTENANCE PROCEDURES

4. Add fluid as required. Do not overfill. Use only the recommended

brake fluid. Refer to Recommended Brake Fluid in this subsection.

CAUTION

Avoid getting brake fluid on skin or eyes - it may cause severe

burns. In case of contact with the skin, wash thoroughly. In

case of contact with the eyes, immediately rinse with plenty of

water for at least 10 minutes and then consult a doctor

immediately.

NOTICE

– Brake fluid can damage paint, rubber and plastic parts

– Protect these nearby parts with a rag when servicing the

brake system

– Rinse thoroughly in case of spillage.

5. Ensure the diaphragm is pushed in the reservoir cap before instal-

ling the cap one the reservoir.

170

MAINTENANCE PROCEDURES

Chaiincase Oill

Recommended Chaincase Oil

XPS Synthetic chaincase oil

Alternative or if not available

75W140 gear oil that meets the API GL-5 specification

NOTICE

If the recommended XPS chaincase oil is not available, use a

75W140 gear oil that meets the API GL-5 specification. The

chaincase of this snowmobile has been developed and vali-

dated using the XPS™ Synthetic chaincase oil. BRP strongly

recommends the use of its XPS Synthetic chaincase oil at all

times. Damages caused by oil which is not suitable for the

chaincase will not be covered by the BRP limited warranty.

Verifying the Chaincase Oil Level

With the vehicle on a level surface, check the oil level by removing the

check plug.

CHECK PLUG

Oil level must reach the threaded hole.

172

MAINTENANCE PROCEDURES

If level is correct, reinstall check plug and tighten to the specified

torque.

Tightening Torque

Check plug

6 ± 1 Nm (53 ± 9 lbf-in)

If level is insufficient, refer to Chaincase Filling Procedure.

Replacing the Chaincase Oil

Draiining the Chaiincase Oiil

1. Place the vehicle on a level surface.

2. Place a drain pan under the chaincase drain plug area.

3. Remove filler cap.

4. Remove the drain plug located at the bottom of the chaincase.

5. Wait a while to allow all oil to drain out of the chaincase.

6. Install drain plug and tighten to specification.

Tightening Torque

Chaincase drain plug

6 ± 1 Nm (53 ± 9 lbf-in)

Fillliing the Chaiincase

1. Open the RH side panel. Refer to Equipment.

173

MAINTENANCE PROCEDURES

Drive Belt

Drive Belt Inspection

Remove the drive belt guard. Refer to the procedure in Equipment.

Inspect belt for cracks, fraying or abnormal wear (uneven wear, wear

on one side, missing cogs, cracked fabric). If abnormal wear is noted,

probable cause could be pulley misalignment, excessive RPM with

frozen track, fast starts without warm-up period, burred or rusty

sheave, oil on belt or distorted spare belt. Contact an authorized BRP

snowmobile dealer.

Replacing the Drive Belt

Removiing the Driive Belt

1. Remove the tether cord cap from engine cut-off switch.

2. Remove the LH side panel.

3. Remove the drive belt guard. Refer to Removing the Drive Belt

Guard.

4. Insert the driven pulley expander provided, in the threaded hole on

the adjuster hub as shown.

TYPICAL - PULLEY EXPANDER INSTALLED ON ADJUSTER

HUB

5. Open the driven pulley by screwing the tool in.

6. Remove the drive belt by slipping it over the edge of the driven pul-

ley, then over the drive pulley.

176

MAINTENANCE PROCEDURES

Installliing the Drive Belt

The driven pulley must be expanded. Refer to Removing the Drive

Belt.

1. Slip the belt over the drive pulley, then over the driven pulley.

NOTICE

Do not force or use tools to pry the belt into place, as this could

cut or break the cords in the belt.

NOTE:

The maximum drive belt life span is obtained when belt is installed

with arrows in the direction of rotation.

1. To be pointed in the direction of rotation

2. Unscrew and remove the driven pulley expander from the pulley.

3. Rotate the driven pulley several times to properly set the belt be-

tween the sheaves.

4. If a new belt was installed, an adjustment will be required for the

proper belt height. Refer to Adjusting the Drive Belt Height.

5. Install belt guard.

6. Close side panel.

Adjusting the Drive Belt Height

Remove the tether cord cap from engine cut-off switch.

Remove the LH side panel.

Remove the drive belt guard.

The drive belt height must be checked every time a new drive belt is

installed and as part of the pre-ride inspection.

1. Loosen the clamping screw.

177

MAINTENANCE PROCEDURES

Drive Pulley

Drive Pulley Adjustment (if equipped)

WARNING

Remove tether cord cap from engine cut-off switch before per-

forming any adjustment. Vehicle must be parked in a safe

place, away from the trail.

WARNING

NEVER disassemble or modify the drive pulley.

Improper assembly or modifications could cause the pulley to

explode violently under the stress generated by the high rota-

tional speed.

Visit your BRP snowmobile dealer to maintain or service the

drive pulley. Improper servicing or maintenance may affect per-

formance and reduce belt life. Always respect maintenance

schedules.

The drive pulley is factory calibrated to transmit maximum engine

power at a predefined RPM. Factors such as ambient temperature, al-

titude or surface condition may vary this critical engine RPM thus af-

fecting snowmobile efficiency.

This adjustable drive pulley allows setting maximum engine RPM to

maintain maximum power.

Ramp cams should be adjusted so that actual maximum engine RPM

matches the maximum horsepower RPM. Refer to Technical Specifi-

cations (Engine).

NOTE:

Use a precision digital tachometer for engine RPM adjustment.

There are 5 positions in which the ramp cam can be set.

Each position modifies the maximum engine RPM by about 200 RPM.

Lower position numbers decrease engine RPM in steps of 200 RPM

and higher position numbers increase it in steps of 200 RPM.

Procedure

1. Refer to Body and Seat in Vehicle Information and remove:

- LH side panel

- Drive pulley guard

182

MAINTENANCE PROCEDURES

Lift the rear of the snowmobile and support it with a wide-base snow-

mobile mechanical stand with a rear deflector panel. With the engine

off, rotate the track by hand, and inspect condition. If worn or cut, or if

track fibers are exposed, or if missing or defective inserts or guides

are noted; contact an authorized BRP snowmobile dealer.

Snowmobiles Equipped with Traction Enhancing Products

If your snowmobile is equipped with a BRP approved studded track,

PROCEED WITH A VISUAL INSPECTION OF YOUR TRACK BE-

FORE EACH USE.

Look for any defects, such as:

- Perforations in the track

- Tears in the track (particularly around traction holes on studded

tracks)

- Lugs that are broken or torn off, exposing portions of rods

- Delamination of the rubber

- Broken rods

- Broken studs (studded tracks)

- Bent studs (studded tracks)

- Missing studs

- Studs that are torn off the track

- Missing track guide(s)

- Also, ensure that studs nut are tighten to the recommended

torque.

On approved studded tracks, replace broken or damaged studs imme-

diately. If your track shows signs of deterioration, it must be replaced

immediately. When in doubt, ask your dealer.

WARNING

Riding with a damaged track or studs could lead to a loss of

control.

For complete information on traction enhancing products, refer to

TRACTION ENHANCING PRODUCTS in SAFETY INFORMATION at

the beginning of this Operator's Guide.

Track Tension and Alignment

NOTE:

Track tension and alignment are interrelated. Do not adjust one with-

out the other.

187

MAINTENANCE PROCEDURES

WARNING

To prevent serious injury to individuals near the snowmobile:

– NEVER stand behind or near a moving track.

– Always use a wide-base snowmobile stand with a rear de-

flector panel if it is necessary to rotate track.

– When the track is raised off the ground, only run it at the low-

est possible speed.

Centrifugal force could cause debris, damaged or loose studs,

pieces of torn track, or an entire severed track to be violently

thrown backwards out of the tunnel with tremendous force, pos-

sibly resulting in the loss of a leg or other serious injury.

Veriifyiing the Track Tension

NOTE:

Ride the snowmobile in snow about 15 to 20 minutes prior to adjusting

track tension.

1. Remove tether cord cap from engine cut-off switch.

2. Lift rear of vehicle and support it off the ground.

CAUTION

Use proper lifting techniques, notably using your legs force. Do

not attempt to lift the rear of vehicle if it is above your limits.

3. Allow rear suspension to fully extend.

4. Prepare the tensiometer.

Service tool

Tensiometer (P/N 414348200)

1. Set the bottom O-ring as per the Track Deflection from the ap-

plicable vehicle in the Technical Specifications table.

188

MAINTENANCE PROCEDURES

CAUTION

Use proper lifting techniques, notably using your legs force. Do

not attempt to lift the rear of vehicle if it is above your limits.

3. Remove wheel cap.

4. Loosen the rear axle screws.

5. Loosen or tighten both adjustment screws (equally) to decrease or

increase track tension.

PPS3

1. Remove wheel cap

2. Loosen the axle screw

3. Loosen or tighten the adjustment screws

6. If correct tension is unattainable, contact an authorized Lynx

dealer.

7. Retighten the rear axle nut to specification.

TIGHTENING TORQUE

Rear idler wheel screw

48 ± 6 Nm (35 ± 4 lbf-ft)

8. Check track alignment as described below.

191

MAINTENANCE PROCEDURES

Aliigniing the Track

WARNING

Before checking track alignment, ensure that the track is free of

all particles which could be thrown out while track is rotating.

Keep hands, tools, feet and clothing clear of track. Always lift

the snowmobile on a wide-base stand with a rear deflector pan-

el. Ensure no one is standing in close proximity to the snowmo-

bile, especially at the rear of the track. Never rotate track at

high speed.

Centrifugal force could cause debris, damaged or loose studs,

pieces of torn track, or an entire severed track to be violently

thrown backwards out of the tunnel with tremendous force.

1. Lift rear of vehicle and support it off the ground.

CAUTION

Use proper lifting techniques, notably by using the force of your

legs . Do not attempt to lift the rear of vehicle if it is above your

limits.

2. Start engine and accelerate slightly so that track slowly turns. This

must be done in a short period of time (15 to 20 seconds).

3. Check that the track is well centered; equal distance on both sides

between edges of track guides and slider shoes.

A01F05A

1. Guides

2. Slider shoes

3. Equal distance

192

MAINTENANCE PROCEDURES

4. To correct track alignment:

1. Guides

2. Slider shoes

3. Tighten on this side

1. Stop engine.

2. Remove tether cord cap from engine cut-off switch.

WARNING

Remove tether cord cap from engine cut-off switch before per-

forming any maintenance or adjustment, unless otherwise

specified. Vehicle must be parked in a safe place, away from

the trail.

3. Loosen the rear axle nut.

4. Tighten adjustment screw on side where the slider shoe is the

farthest from the track insert guides.

5. Tighten the rear axle nut.

WARNING

Properly tighten wheel retaining bolt, otherwise wheel may

come off and cause track to “lock”.

6. Restart engine and rotate track slowly to recheck alignment.

7. Tighten the rear axle nut to specified torque.

193

MAINTENANCE PROCEDURES

Tightening Torque

Rear axle screw

48 ± 6 Nm (35 ± 4 lbf-ft)

8. Reposition snowmobile on the ground.

Suspensiion

Steering and Front Suspension Condition

Visually inspect steering and front suspension for tightness of compo-

nents (steering arms, control arms and links, tie rods, ball joints, ski

bolts, ski legs, etc.). If necessary, contact an authorized BRP snowmo-

bile dealer.

Suspension Stopper Strap Condition

Inspect stopper straps for wear and cracks, bolt and nut for tightness.

If loose inspect holes for deformation. Replace as required. Tighten

nut to specification.

Tightening Torque

Stopper strap nut

7 ± 1 Nm (62 ± 9 lbf-in)

Rear Suspension Condition

Visually inspect all suspension components including slider shoes,

springs, wheels, etc.

NOTE:

During normal driving, snow will act as a lubricant and coolant for the

slider shoes. Extensive riding on ice or sanded snow, will create ex-

cessive heat build-up and cause premature slider shoe wear.

Suspension Lubrication – PPS

Lubricate the following suspension pivots at grease fittings. Refer to

MAINTENANCE SCHEDULE for maintenance frequency.

SUSPENSION GREASE

XPS Synthetic suspension grease

194

VEHICLE CARE

Post-Operatiion Care

Remove snow and ice from rear suspension, track, front suspension,

steering mechanism and skis.

WARNING

Make sure D.E.S.S. key is removed from D.E.S.S. post before

standing in front the vehicle, getting close to the track or rear

suspension components.

Always cover your snowmobile when leaving it outside overnight or

during extended periods of inactivity. This will protect it from frost and

snow as well as help retain its appearance.

Vehicle Cleaning and Protectiion

Wash snowmobile using water mixed with a mild detergent.

Use only microfiber cloths or an equivalent.

NOTICE

Never use a high pressure washer to clean the vehicle. Use low

pressure only, like a garden hose.

Non Compatible Cleaning Products

Material Type

Non-Compatible Cleaning Products

BRAKE AND PARTS CLEANER

All plastics, vinyls,

painted steel and

ANY PETROLEUM BASE CLEANING

aluminium

PRODUCTS

Compatible Cleaning Products

Material Type

Cleaning Product

All plastics, vinyls,

Automotive type soap with water

painted steel and

XPS Spray Cleaner and Polish

aluminium.

XPS All Purpose Cleaner

For more information and products, Visit the XPS Products website at

www.xpslubricants.com

203

STORAGE

During summer, or when a snowmobile is not in use for more than

three months, proper storage is necessary.

Storage

Clean the vehicle

Add fuel stabilizer to fuel following the product manufacturer

recommendations.

Run the engine after adding the product to the fuel

Lubricate engine. Refer to Engine Storage Procedure in this

section.

Lubricate brake lever pivot

Lubricate rear suspension

Charge battery monthly to keep it fully charged during storage (if

equipped)

Block muffler outlet with rags

Lift rear of vehicle until track is clear of the ground. Do not release

track tension

CAUTION

Use appropriate lifting device or have assistance to share lifting

stress. If a lifting device is not used, use proper lifting techni-

ques, notably using your legs force. Do not attempt to lift the

rear of vehicle if it is above your limits.

NOTICE

The snowmobile has to be stored in a cool and dry place and

covered with an opaque but ventilated tarpaulin. This will pre-

vent sun rays and grime from affecting plastic components and

vehicle finish.

NOTICE

Fuel stabilizer should be added prior to engine lubrication to

prevent the loss of the chemical properties of fuel and protect

the fuel system against varnish deposits.

204

STORAGE

Engine Storage Procedure

The engine has to be properly lubricated at storage for internal parts

protection.

E-TEC Engine - 4.5” and 7.2” Digital Display

Follow these simple steps.

To engage the procedure, do the following:

1. Place the vehicle in a well ventilated area.

2. Start the engine and let it run at idle speed until it reaches its oper-

ating temperature (watch the coolant temperature on the display or

verify the rear heat exchanger becomes warm).

3. Push the SET (S) button to select odometer mode.

TYPICAL

NOTE:

The storage mode does not function in other modes (trip A, trip B and

hr trip).

4. Repeatedly depress the HI/LOW beam switch rapidly, then, while

doing this, press and hold the SET button until PUSH "S" ap-

pears on the display.

TYPICAL

205

STORAGE

5. Release all buttons when gauge displays PUSH (S) appears.

6. Again, press and hold the SET (S) button for 2 - 3 seconds.

NOTE:

The gauge will display OIL when the storage procedure is initiated.

7. When gauge displays OIL, release button and wait for the lubrica-

tion function to end.

TYPICAL

Do not touch anything during engine lubrication cycle.

The engine lubrication function takes approximately 1 minute. Dur-

ing this time the engine RPM will increase slightly to approximately

1600 RPM and the oil pump will "oil flood" the engine.

At the end of engine lubrication procedure, the ECM will turn the

engine off.

Remove tether cord cap from engine cut-off switch.

NOTICE

Do not start the engine during storage period.

206

VEHICLE IDENTIFICATION

Identificatiion Numbers

The main components of your snowmobile (engine and frame) are

identified by different identification numbers. It may sometimes be-

come necessary to locate these numbers for warranty purposes or to

trace your snowmobile in the event of loss. These numbers are re-

quired by the authorized BRP snowmobile dealer to complete war-

ranty claims properly. We strongly recommend that you take note of

all the identification numbers on your snowmobile and supply them to

your insurance company.

Vehicle Identification Number (VIN)

VIN is scribed on vehicle description decal. See above. It is also en-

graved on tunnel near vehicle description decal.

Model number and model year are part of the information found in the

VIN. See illustration.

2BP

LSAB

000001

2BP = Canada

Serial

Model number

YH2 = Finland

number

Factory

S = Ski-Doo

V = Valcourt

L = Lynx

R = Rovaniemi

Numeric or

Alphabetic

Model year: P = 2023

R= 2024

219

EPA CERTIFIED ENGINES

Engine Emiissiions Information

Manufacturer''s Responsibility

Snowmobile manufacturers of snowmobile engines need to determine

the exhaust emission levels for each engine horsepower family and

certify these engines with the United States of America Environmental

Protection Agency (EPA). An emissions control information label,

showing emission levels and engine specifications, must be placed on

each vehicle at the time of manufacture.

Dealer''s Responsibility

When performing service on a certified BRP snowmobiles that carry

an emissions control information label, adjustments must be kept with-

in published factory specifications.

Replacement or repair of any emission related component must be

executed in a manner that maintains emission levels within the pre-

scribed certification standards.

Dealers are not to modify the engine in any manner that would alter

the horsepower or allow emission levels to exceed their predeter-

mined factory specifications.

Exceptions include manufacturer's prescribed changes, such as alti-

tude adjustments for example.

Owner’s Responsibility

The owner / operator is required to have engine maintenance per-

formed to maintain emission levels within prescribed certification

standards.

The owner / operator is not to, and should not allow anyone to modify

the engine in any manner that would alter the horsepower or allow

emissions levels to exceed their predetermined factory specifications.

EPA Emission Regulations

All BRP snowmobiles manufactured by BRP are certified to the EPA

as conforming to the requirements of the regulations for the control of

air pollution from new snowmobile engines. This certification is contin-

gent on certain adjustments being set to factory standards. For this

reason, the factory procedure for servicing the product must be strictly

followed and, whenever practicable, returned to the original intent of

the design.

The responsibilities listed above are general and in no way a complete

listing of the rules and regulations pertaining to the EPA requirements

on exhaust emissions for snowmobile products. For more detailed in-

formation on this subject, you may contact the following locations:

229

RADIO FREQUENCY DIGITALLY ENCODED

SECURITY SYSTEM (RF D.E.S.S. KEY)

This device complies with FCC Part 15 and Industry Canada license

exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any inter-

ference, including interference that may cause undesired operation of

the device.

Changes or modifications not expressly approved by the party respon-

sible for compliance could void the user’s authority to operate the

equipment.

IC Registration Number: 12006A-1001301698

FCC ID: 2ACER-1001301698

We, the party responsible for compliance, declare under our sole re-

sponsibility that the device is in conformity with the provisions of the

following Council Directive: 2014/53/EU. To which this declaration re-

lates is in conformity with the essential requirements and other rele-

vant requirements. The product is in conformity with the following

directives, harmonized standards and regulations:

Radio Equipment Directive

(RED)

2014/53/EU and Harmonized

Standards:

IEC 62368-1:2014, CISPR 25:2016, ISO 11452-2:2004, ETSI EN 300

330 V2.1.1:2017

Radio Equipment Statutory Instrument 2017/1206 and Designated

Standards:

IEC 62368-1:2014, CISPR 25:2016, ISO 11452-2:2004, ETSI EN 300

330 V2.1.1:2017

231

MULTIFUNCTION GAUGE REGULATORY

INFORMATION

Technical Information

Transmitter:

- BT operating frequency range: 2402 - 2480 MHz

- BT version: 4.2 (no BTLE)

- BT output power: < 8.5 dBm

Receiver:

- FM operating range: 76 - 108 MHz

Manufacturer and Address

Manufacturer:

- Robert Bosch LLC

Address:

38000 Hills Tech Drive,

Farmington Hills, MI 48331,

USA

To display the regulatory information on the vehicle digital

display:

From the home screen, access the main menu and keep the joystick

pressed down for more than 10 seconds.

USA and Canada

This device complies with FCC Part 15 and Industry Canada license

exempt RSS standard (s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada appli-

cables aux appareils radio exempts de licence. L'exploitation est au-

torisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectri-

que subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

Changes or modifications not expressly approved by the party respon-

sible for compliance could void the user's authority to operate the

equipment.

IC: 22868 - VDIBRHS01

FCC ID: 2AMJS - VDIBRHS01

RF exposure:

232

MULTIFUNCTION GAUGE REGULATORY INFORMATION

- The equipment complies with FCC RF exposure limits set forth for

an uncontrolled environment.

- This equipment must be installed and operated with a separation

distance of at least 20 cm from all persons.

- The antenna(s) used for this transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

Mexico

IFETEL

Marca: Robert Bosch LLC

Modelo(s): VIPHI2BT

Número: RCPBOVI18-0967

NOM-121-SCT1-2009

La operación de este equipo está sujeta a las siguientes dos condi-

ciones: (1) es posible que este equipo o dispositivo no cause interfer-

encia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su operación no

deseada.

Brazil

03473-18-04473

Este equipamento opera em caráter secundário, isto é, não tem direito

a proteção contra interferência prejudicial, mesmo de estações do

mesmo tipo, e não pode causar interferência a sistemas operando em

caráter primário.

Japan

This device is granted pursuant to the Japanese Radio Law (

)

and the Japanese Telecommunications Business Law

(

). This device should not be modified (otherwise the

granted designation number will become invalid).

233

MULTIFUNCTION GAUGE REGULATORY INFORMATION

Europe

Declaration of Conformity

Simplified EU Declaration of Conformity according Radio Equipment

Directive 2014/53/EU.

Hiermit erklärt Robert Bosch LLC, dass der Funkanlagentyp VIPHI2BT der Richtlinie 2014/53/EU entspricht.

Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: eu-doc.

bosch.com

Le soussigné, Robert Bosch LLC, déclare que l'équipement radioélectrique du type VIPHI2BT est conforme à la

directive 2014/53/UE.

Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante:eu-doc.

bosch.com

Robert Bosch LLC

VIPHI2BT

2014/53/.

: eu-doc.

bosch.com

Με την παρούσα ο/η Robert Bosch LLC, δηλώνει ότι ο ραδιοεξοπλισ×όØ VIPHI2BT πληροί την οδηγία 2014/53/EE.

Το πλήρεØ κεί×ενο τηØ δήλωσηØ συ××όρφωσηØ ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: eu-doc.

bosch.com

Tímto Robert Bosch LLC prohlašuje, že typ rádiového zařízení VIPHI2BT je v souladu se směrnicí 2014/53/EU.

Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: eu-doc.bosch.com

Hermed erklærer Robert Bosch LLC, at radioudstyrstypen VIPHI2BT er i overensstemmelse med direktiv

2014/53/EU.

EU-overensstemmelseserklæringens fulde tekst kan ðndes på følgende internetadresse: eu-doc.bosch.com

Käesolevaga deklareerib Robert Bosch LLC, et käesolev raadioseadme tüüp VIPHI2BT vastab direktiivi

2014/53/EL nõuetele.

ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: eu-doc.bosch.com

Por la presente, Robert Bosch LLC declara que el tipo de equipo radioeléctrico VIPHI2BT es conforme con la

Directiva 2014/53/UE.

El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: eu-doc.

bosch.com

Robert Bosch LLC vakuuttaa, että radiolaitetyyppi VIPHI2BT on direktiivin 2014/53/EU mukainen.

EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: eu-doc.

bosch.com

Hereby, Robert Bosch LLC declares that the radio equipment type VIPHI2BT is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: eu-doc.bosch.com

Robert Bosch LLC ovime izjavljuje da je radijska oprema tipa VIPHI2BT u skladu s Direktivom 2014/53/EU.

Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: eu-doc.bosch.com

Robert Bosch LLC igazolja, hogy a VIPHI2BT típusú rádióberendezés megfelel a 2014/53/EU irányelvnek.

Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: eu-doc.bosch.com

Il fabbricante, Robert Bosch LLC, dichiara che il tipo di apparecchiatura radio VIPHI2BT è conforme alla direttiva

2014/53/UE.

Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: eu-doc.

bosch.com

234

MULTIFUNCTION GAUGE REGULATORY INFORMATION

Aš, Robert Bosch LLC, patvirtinu, kad radijo įrenginių tipas VIPHI2BT atitinka Direktyvą 2014/53/ES.

Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: eu-doc.bosch.com

Ar šo Robert Bosch LLC deklarē, ka radioiekārta VIPHI2BT atbilst Direktīvai 2014/53/ES.

Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: eu-doc.bosch.com

B'dan, Robert Bosch LLC, niddikjara li dan it-tip ta' tagħmir tar-radju VIPHI2BT huwa konformi mad-Direttiva

2014/53/UE.

It-test kollu tad-dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: eudoc.

bosch.com

Hierbij verklaar ik, Robert Bosch LLC, dat het type radioapparatuur VIPHI2BT conform is met Richtlijn

2014/53/EU.

De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: eudoc.

bosch.com

Robert Bosch LLC niniejszym oświadcza, że typ urządzenia radiowego VIPHI2BT jest zgodny z dyrektywą

2014/53/UE.

Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: eu-doc.bosch.com

O(a) abaixo assinado(a) Robert Bosch LLC declara que o presente tipo de equipamento de rádio VIPHI2BT está

em conformidade com a Diretiva 2014/53/UE.

O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: eudoc.

bosch.com

Prin prezenta, Robert Bosch LLC declară că tipul de echipamente radio VIPHI2BT este în conformitate cu

Directiva 2014/53/UE.

Textul integral al declaraiei UE de conformitate este disponibil la următoarea adresă internet: eu-doc.bosch.com

Härmed försäkrar Robert Bosch LLC att denna typ av radioutrustning VIPHI2BT överensstämmer med direktiv

2014/53/EU.

Den fullständiga texten till EU-försäkran om överensstämmelse nns på följande webbadress: eu-doc.bosch.com

Robert Bosch LLC potrjuje, da je tip radijske opreme VIPHI2BT skladen z Direktivo 2014/53/EU.

Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: eu-doc.bosch.com

Robert Bosch LLC týmto vyhlasuje, že rádiové zariadenie typu VIPHI2BT je v súlade so smernicou 2014/53/EÚ.

Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: eu-doc.bosch.com

Robert Bosch LLC lýsir því hér með yr að þráðlausi arskiptabúnaðurinn VIPHI2BT er í samræmi við tilskipun

2014/53/ESB.

Óstyttan texta ESB-samræmisyrlýsingarinnar er að nna á ve anginu: eu-doc.bosch.com

Liechtenstein

Hiermit erklärt Robert Bosch LLC, dass der Funkanlagentyp VIPHI2BT der Richtlinie 2014/53/EU entspricht.

Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: eudoc.

bosch.com

Hermed erklærer Robert Bosch LLC at radioutstyrstypen VIPHI2BT er i samsvar med direktiv 2014/53/EU.

Hele teksten i EU-samsvarserklæringen nnes på følgende internettadresse: eu-doc.bosch.com

235

VEHICLE

49 Ranger Pro Seriies

COOLING SYSTEM

XPS

XPS Extended life

recommended

pre-mixed coolant

coolant

Ethyl glycol and

Coolant type

distilled water (50%/

If the XPS

50%)

product is not

or coolant

available

specifically

formulated for

aluminum engines

Coolant capacity

8.8 l (9.3 qt(liq.,US))

FUEL SYSTEM

In-tank electrical

Fuel pump

fuel pump

Premium unleaded

gasoline (fuel which

Type

may contain up to

10% MAX ethanol)

Fuel

91 Pump Posted

Octane rating

AKI ((R+M)/2)

(RON)

37 l (39.1

Fuel tank capacity

qt(liq.,US))

ELECTRICAL SYSTEM (Electric Start)

Battery (if equipped)

12 V, 18 A•h

Headlamp

LED

Taillight and stoplight

LED

Battery (if

Fuses

30 A

equipped)

242

VEHICLE

DRIVE SYSTEM - PULLEYS

Drive pulley type

pDrive with clickers

49 Ranger Pro

3400 ± 100 RPM

600R E-TEC

Drive pulley engagement

RPM

49 Ranger Pro

3000 ± 100 RPM

850 E-TEC

Driven pulley type

QRS-VENT+

DRIVE SYSTEM - TRACK

Drive sprocket number of teeth

Width

38cm (15 in)

Track

Length

391.2 cm (154 in)

Profile height

6.35 mm (2.5 in)

Track

Deflection

40 mm (1.9/16 in)

adjust

ment⁽³⁾

Force

7.3 kgf(16.1 lbf)

BRAKE SYSTEM

Single 200 mm

Brake

Type

cross drilled carbon

steel disc

Type

DOT 4

Brake fluid

65 ml (2.2 fl

Quantity

oz(US))

Fixed twin pistons

Caliper

(2 x 40 mm)

Organic

Brake pad material

Ferrite

244

TROUBLESHOOTING GUIDELINES – E-TEC

ENGINES

ELECTRIC STARTER DOES NOT WORK

1. Emergency engine stop switch in OFF position or tether

cord cap not installed on engine cut-off switch.

- Place the emergency engine stop switch in the ON position

and install tether cord cap (on engine cut-off switch.

2. Throttle applied while attempting an engine start.

- Release throttle while cranking.

ENGINE IS CRANKING BUT FAILS TO START

1. No fuel to the engine.

- Check fuel tank level, add fuel if necessary.

2. System voltage too low.

- Contact an authorized BRP snowmobile dealer.

ENGINE RPM DOES NOT REACH CLUTCH ENGAGEMENT

POINT

1. D.E.S.S. did not read D.E.S.S. key code in the tether cord

cap. D.E.S.S. pilot lamp blinks (slow short beeps/

repetitive).

- Properly install tether cord cap.

2. D.E.S.S. has read a different code than the one

programmed. D.E.S.S. pilot lamp blinks rapidly (fast short

beeps/repetitive).

- Install a tether cord cap for which this snowmobile was

programmed.

3. ECM does not recognize the D.E.S.S. key.

- Refer to an authorized BRP snowmobile dealer.

248

TROUBLESHOOTING GUIDELINES - E-TEC ENGINES

ENGINE LACKS ACCELERATION OR POWER

Engine warm-up in progress.

- Drive vehicle at low speeds for a few minutes.

Engine break-in period not completed.

- Complete break-in period.

Drive and driven pulleys require servicing.

- Contact an authorized BRP snowmobile dealer.

Engine overheats.

- Check coolant level, see Maintenance procedures.

- Check heat exchangers cleanliness. Clean if necessary.

Drive belt worn too thin.

- If the drive belt has lost more than 3 mm (1/8 in) of its

original width, it will affect vehicle performance.

- Replace drive belt.

Incorrect track adjustment.

- See MAINTENANCE and/or an authorized Lynx dealer for

proper alignment and tension adjustments.

R.A.V.E. valves problem.

- Seek service from an authorized BRP snowmobile dealer,

repair shop, or person of your own choosing for

maintenance, repair, or replacement.

Fuel pressure too low.

- Seek service from an authorized BRP snowmobile dealer,

repair shop, or person of your own choosing for

maintenance, repair, or replacement.

249

TROUBLESHOOTING GUIDELINES - E-TEC ENGINES

ENGINE BACKFIRES

1. Engine is running too hot.

- See item 4 of ENGINE LACKS POWER.

2. Ignition timing is incorrect or there is an ignition system

failure.

- Seek service from an authorized BRP snowmobile dealer,

repair shop, or person of your own choosing for

maintenance, repair, or replacement.

3. Exhaust system leak.

- Seek service from an authorized BRP snowmobile dealer,

repair shop, or person of your own choosing for

maintenance, repair, or replacement.

4. Fuel pressure too low.

- Seek service from an authorized BRP snowmobile dealer,

repair shop, or person of your own choosing for

maintenance, repair, or replacement.

ENGINE MISFIRES

1. Water in fuel.

- Drain fuel system and refill with fresh fuel.

2. RAVE valves malfunction.

- Have RAVE valves system inspected. Seek service from an

authorized BRP snowmobile dealer, repair shop, or person

of your own choosing for maintenance, repair, or

replacement.

HEATED GRIPS/THUMB WARMERS ARE NOT WORKING

1. Engine RPM is too low.

- Make sure engine RPM is above 2000.

ENGINE HAS SHUT DOWN

1. The engine shuts down after long periods of idling.

- Do not let engine idle too long. Refer to Vehicle warm-up in

operating instruction.

250

MONITORING SYSTEM

Pilot

Message

lamp

Beeper

Description

display

Engine is overheating,

reduce snowmobile

speed and run in loose

snow or stop engine

immediately and let

engine cool down.

HIGH

Check coolant level,

ENGINE

refer to Maintenance. If

TEMPERA

coolant level is correct

TURE

and overheating

persists, contact an

1 Long

authorized BRP

beep

snowmobile dealer. Do

repeat

not run the engine if

ing

condition persists.

Reduce speed or stop

engine. Let engine cool

down and restart. If

overheating persists,

MUFFLER

contact an authorized

OVERHEAT

BRP snowmobile

dealer. Do not run the

engine if condition

persists.

Critical overheat. Stop

engine immediately and

let engine cool down.

Check coolant level,

1 Long

HIGH

refer to Maintenance. If

beep

ENGINE

coolant level is correct

repeat

TEMPERA

and overheating

ing

TURE

persists, contact an

authorized BRP

snowmobile dealer. Do

not run the engine if

condition persists.

253

MONITORING SYSTEM

Pilot

Message

lamp

Beeper

Description

display

MUFFLER

Critical overheat. Stop

OVERHEAT

engine immediately and

let engine cool down. If

overheating persists,

contact an authorized

ECM

BRP snowmobile

OVERHEAT

dealer. Do not run the

engine if condition

persists.

Indicate a low or high

battery voltage

—

condition. See an

BATT VOLT

authorized BRP

snowmobile dealer as

soon as possible.

Engine fault, see an

1 Long

authorized BRP

beep

CHECK

snowmobile dealer,

repeat

ENGINE

repair shop or person of

ing

your own choosing as

soon as possible.

Displayed when brake is

applied for more than 15

seconds while throttle

—

lever is squeezed and

vehicle is moving at

more than 5 km/h (3

MPH).

Engine detonation

(RPM is limited when

4 short

this condition occurs).

beeps

—

KNOCK

- Ensure

every 5

recommended fuel is

minutes

used.

- Check fuel quality,

replace if

254

BRP INTERNATIONAL LIMITED WARRANTY:

2024 LYNX® SNOWMOBILES

SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. (“BRP”) warrants its 2024

LYNX snowmobiles sold by distributors or dealers authorized by BRP

to distribute LYNX snowmobiles ("LYNX Distributor / Dealer") outside

of the fifty United States, Canada, members of the European Econom-

ic Area (which is comprised of the member states of the European

Union plus United Kingdom, Norway, Iceland and Liechtenstein)

(“EEA”), members states of the Commonwealth of the Independent

States (including Ukraine and Turkmenistan) (''CIS'') and Turkey, from

defects in material or workmanship for the period and under the condi-

tions described below.

Non-factory installed parts and accessories are not covered under this

limited warranty. Please refer to the applicable parts and accessories

limited warranty text.

This limited warranty will become null and void if: (1) the snowmobile

was used for racing or any other competitive activity, at any point,

even by a previous owner; or (2) the snowmobile has been altered or

modified in such a way so as to adversely affect its operation, perform-

ance or durability, or has been altered or modified to change its in-

tended use.

LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS

EXPRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND

ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, IN-

CLUDING WITHOUT LIMITATION ANY WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE

LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CON-

SEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE

UNDER THIS WARRANTY. SOME STATES/PROVINCES DO

NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS AND EX-

CLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC

RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS

WHICH MAY VARY FROM COUNTRY TO COUNTRY. BRP

SHALL NOT BE HELD LIABLE IF PRODUCTS OR WARRANTY

PARTS ARE NOT AVAILABLE IN CERTAIN COUNTRIES FOR

REASONS OUTSIDE OF BRP’S CONTROL.

For Products purchased in Australia, refer to the Australia-specific

section below.

Neither the distributor, any BRP Distributor/Dealer nor any other per-

son has been authorized to make any affirmation, representation or

258

BRP INTERNATIONAL LIMITED WARRANTY: 2024 LYNX^® SNOWMOBILES

warranty regarding the product, other than those contained in this lim-

ited warranty, and if made, shall not be enforceable against BRP.

BRP reserves the right to modify this limited warranty at any time,

being understood that such modification will not alter the warranty con-

ditions applicable to the Products sold while this warranty is in effect.

EXCLUSIONS – ARE NOT WARRANTED

The following are not warranted under this limited warranty under any

circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper mainte-

nance and/or storage, as described in the operator's guide;

Damage resulting from removal of parts, improper repairs, service,

maintenance, modifications or use of parts or accessories not

manufactured or approved by BRP which in its reasonable judge-

ment are either incompatible with the product or adversely affect

its operation, performance and durability, or resulting from repairs

done by a person that is not an authorized servicing BRP snowmo-

bile distributor/ dealer;

Damage caused by abuse, abnormal use, neglect, racing or opera-

tion of the product on surfaces other than snow, or operation of the

product in a manner inconsistent with the recommended operation

described in the Operator’s Guide;

Damage resulting from accident, submersion, fire, snow or water

ingestion, theft, vandalism or any act of God;

Operation with fuels, oils or lubricants which are not suitable for

use with the product (see the Operator’s Guide);

Damage resulting from rust, corrosion or exposure to the

elements;

Incidental or consequential damages, or damages of any kind in-

cluding without limitation towing, storage, transportation expenses,

telephone, rental, taxi, inconvenience, insurance coverage, loan

payments, loss of time, loss of income; or time missed for down-

time experience due to service work.

And damage resulting from studs installed on tracks if the installa-

tion does not conform to BRP’s instructions.

WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to

the first retail consumer, or (2) the date the product is first put into use,

whichever occurs first and for the applicable period below:

1. TWELVE (12) consecutive months, for private use or commercial

use owners. However, the warranty coverage period on a

259

BRP INTERNATIONAL LIMITED WARRANTY: 2024 LYNX^® SNOWMOBILES

snowmobile delivered between June 1^st and December 1^st of a giv-

en year will expire November 30^th of the following year.

The repair or replacement of parts or the performance of service under

this warranty does not extend the life of this warranty beyond its origi-

nal expiration date.

The warranty coverage period identified above are a minimal limited

warranty period which can be extended by any applicable warranty

promotional program, as the case may be.

Note that the duration and any other modalities of the warranty cover-

age are subject to the applicable national or local legislation in the cus-

tomer's country.

FOR PRODUCTS SOLD IN AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the

Australian Consumer Law. You are entitled to a replacement or refund

for a major failure and for compensation for any other reasonably fore-

seeable loss or damage. You are also entitled to have the goods re-

paired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Nothing in these Warranty terms and conditions should be taken to ex-

clude, restrict or modify the application of any condition, warranty,

guarantee, right or remedy conferred or implied under the Competition

and Consumer Act 2010 (Cth), including the Australian Consumer

Law or any other law, where to do so would contravene that law, or

cause any part of these terms and conditions to be void. The benefits

given to you under this limited warranty are in addition to other rights

and remedies that you have under Australian law.

CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following condi-

tions has been fulfilled:

1. The Product must be purchased as new and unused by its first

owner from a Distributor/Dealer authorized to distribute Products in

the country in which the sale occurred (“Distributor/Dealer”);

2. The BRP specified pre-delivery inspection process must be com-

pleted, documented and signed by the purchaser;

3. The Product must have undergone proper registration by an au-

thorized Distributor/Dealer;

4. The Product must be purchased in the country in which the pur-

chaser resides;

5. Routine maintenance outlined in the Operator’s Guide must be

timely performed in order to maintain warranty coverage. BRP re-

serves the right to make warranty coverage contingent upon proof

of proper maintenance.

260

BRP INTERNATIONAL LIMITED WARRANTY: 2024 LYNX^® SNOWMOBILES

BRP will not honor this limited warranty to any private use owner or

commercial use owner if one of the preceding conditions has not been

met. Such limitations are necessary in order to allow BRP to preserve

both the safety of its products, and also that of its consumers and the

general public.

WHAT TO DO TO OBTAIN WARRANTY

COVERAGE

The customer must cease using the Product upon the appearance of

an anomaly, notify a servicing BRP Distributor/Dealer within two (2)

months of the appearance of the anomaly and provide the Distributor/

Dealer with reasonable access to the Product and reasonable oppor-

tunity to repair it.

The notification period is subject to the applicable national or local

legislation in customer's country.

The customer must also present to the Distributor/Dealer, proof of pur-

chase of the Product and must sign the repair/work order prior to start-

ing the repair in order to validate the warranty repair.

All parts replaced under this limited warranty become the property of

BRP.

WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty

are limited to, at its sole discretion, repairing or replacing parts found

defective under normal use, maintenance and service without charge

for parts and labor, at any authorized BRP Distributor/Dealer during

the warranty coverage period under the conditions described herein.

No claim of breach of warranty shall be cause for cancellation or re-

scission of the sale of the Product to the owner. You may have other

legal rights which may vary from country to country.

In the event that service is required outside of the country of original

sale, the owner will bear responsibility for any additional charges due

to local practices and conditions, such as, but not limited to, freight, in-

surance, taxes, license fees, import duties, and any and all other finan-

cial charges, including those levied by governments, states, territories

and their respective agencies.

BRP reserves the right to improve or modify products from time to time

without assuming any obligation to modify products previously

manufactured.

261

BRP INTERNATIONAL LIMITED WARRANTY: 2024 LYNX^® SNOWMOBILES

TRANSFER

If the ownership of a product is transferred during the warranty cover-

age period, this limited warranty, subject to its terms and conditions,

shall also be transferred and be valid for the remaining coverage peri-

od provided BRP or an authorized LYNX Distributor / Dealer receives

a proof that the former owner agreed to the transfer of ownership, in

addition to the coordinates of the new owner.

CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited

warranty, BRP suggests that you try to resolve the issue at the LYNX

Distributor / Dealer level. We recommend discussing the issue with

the authorized LYNX Distributor / Dealer's service manager or owner.

If the matter still remains unresolved, contact BRP by filling out the

customer contact form at www.brp.com or contact BRP by mail at one

of the addresses listed under the CONTACT US section of this guide.

262

BRP LIMITED WARRANTY FOR THE

EUROPEAN ECONOMIC AND THE

COMMONWEALTH OF THE INDEPENDENT

STATES (CIS) AREAS AND TURKEY: 2024

LYNX® SNOWMOBILES

SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024

LYNX^® snowmobiles (“Product(s)”) sold by distributors or dealers au-

thorized by BRP to distribute the Products in member states of the

European Economic Area (which is comprised of the states of the

European Union plus the United Kingdom, Norway, Iceland and Liech-

tenstein) ("EEA"), Turkey, member states of the Commonwealth of the

Independent States (including Ukraine and Turkmenistan)

("CIS")

(“Distributor/Dealer”) from defects in material or workmanship for the

period and under the conditions described below.

This limited warranty will become null and void if:

(1) the Product was used for racing or any other competitive activity,

at any point, even by a previous owner; or

(2) the Product has been altered or modified in such a way so as to ad-

versely affect its operation, performance or durability, or has been al-

tered or modified to change its intended use.

Non-factory installed parts and accessories are not covered under this

limited warranty. Please refer to the applicable parts and accessories

limited warranty text.

LIMITATIONS OF LIABILITY

TO THE EXTEND PERMITTED BY LAW, THIS WARRANTY IS EX-

PRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTH-

ER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING

WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT

THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED WARRAN-

TIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS

WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES

ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY.

SOME STATES/PROVINCES DO NOT ALLOW FOR THE DIS-

CLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE.

AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY

GIVES YOU SPECIFIC RIGHTS, AND YOU MAY ALSO HAVE OTH-

ER LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE,

OR PROVINCE TO PROVINCE. BRP SHALL NOT BE HELD LIABLE

IF PRODUCTS OR WARRANTY PARTS ARE NOT AVAILABLE IN

CERTAIN COUNTRIES FOR REASONS OUTSIDE OF BRP’S

CONTROL.

263

For Products purchased in France, refer to the France-specific section

below.

Neither the distributor, any BRP Distributor/Dealer nor any other per-

son has been authorized to make any affirmation, representation or

warranty regarding the product, other than those contained in this lim-

ited warranty, and if made, shall not be enforceable against BRP.

BRP reserves the right to modify this limited warranty at any time,

being understood that such modification will not alter the warranty con-

ditions applicable to the Products sold while this warranty is in effect.

EXCLUSIONS – ARE NOT WARRANTED

The following are not warranted under this limited warranty under any

circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by negligence or failure to provide proper mainte-

nance and/or storage, as described in the operator's guide;

Damage resulting from removal of parts, improper repairs, service,

maintenance, modifications or use of parts or accessories not

manufactured or approved by BRP which in its reasonable judge-

ment are either incompatible with the product or adversely affect

its operation, performance and durability, or resulting from repairs

done by a person that is not an authorized servicing BRP snowmo-

bile distributor/ dealer;

Damage caused by abuse, abnormal use, neglect, racing or opera-

tion of the product on surfaces other than snow, or operation of the

product in a manner inconsistent with the recommended operation

described in the Operator’s Guide;

Damage resulting from accident, submersion, fire, snow or water

ingestion, theft, vandalism or any act of God;

Operation with fuels, oils or lubricants which are not suitable for

use with the product (see the Operator’s Guide);

Damage resulting from rust, corrosion or exposure to the

elements;

Incidental or consequential damages, or damages of any kind in-

cluding without limitation towing, storage, transportation expenses,

telephone, rental, taxi, inconvenience, insurance coverage, loan

payments, loss of time, loss of income; or time missed for down-

time experience due to service work.

And damage resulting from studs installed on tracks if the installa-

tion does not conform to BRP’s instructions.

264

WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to

the first retail consumer, or (2) the date the product is first put into use,

whichever occurs first and for the applicable period below:

1. TWENTY-FOUR (24) consecutive months, for private use owners.

2. TWELVE (12) consecutive months, for commercial use owners.

However, the warranty coverage period on a snowmobile delivered

between June 1^st and December 1^st of a given year will expire Novem-

ber 30^th of the applicable year. A Product is used commercially when it

is used in connection with any work or employment that generates in-

come during any part of the warranty period. A Product is also used

commercially when, at any point during the warranty period, it is li-

censed for commercial use.

The repair or replacement of parts or the performance of service under

this warranty does not extend the life of this warranty beyond its origi-

nal expiration date.

The warranty coverage period identified above are a minimal limited

warranty period which can be extended by any applicable warranty

promotional program, as the case may be.

Note that the duration and any other modalities of the warranty cover-

age are subject to the applicable national or local legislation in the cus-

tomer's country.

FOR PRODUCTS SOLD IN FRANCE ONLY

The seller shall deliver goods that are complying with the contract and

shall be responsible for defects existing upon delivery. The seller shall

also be responsible for defects resulting from packaging, assembling

instructions or the installation when it is its responsibility per the con-

tract or if accomplished under its responsibility. To be compliant with

the contract, the good shall:

1. Be fit for normal use for goods similar thereto and, if applicable:

Correspond to the description provided by the seller and have the

qualities presented to the buyer though sample or model;

Have the qualities that a buyer may legitimately expect considering

the public declarations of the seller, the manufacturer of its repre-

sentative, including in advertising or labeling; or

2. Have the characteristics mutually agreed upon as between the par-

ties or be fit for the specific use intended by the buyer and brought

to the attention of the seller and which accepted.

The action for failure to comply is prescribed after two years after de-

livery of the goods. The seller is responsible for the warranty for hid-

den defects of the good sold if such hidden defects are rendering the

265

good unfit for the intended use, or if they diminish its use in such a

way that the buyer would not have acquired the good or would have

given a lesser price, had he known. The action for such hidden defects

shall be taken by the buyer within 2 years of the discovery of the

defect.

CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following condi-

tions has been fulfilled:

- The 2024 LYNX snowmobile must be purchased as new and un-

used by its first owner from a LYNX Distributor / Dealer authorized

to distribute LYNX products in the country in which the sale oc-

curred or in the case of EEA, Union of countries;

- The BRP specified pre-delivery inspection process must be com-

pleted and documented;

- The product must have undergone proper registration by an au-

thorized LYNX Distributor / Dealer;

- The 2024 LYNX snowmobile must be purchased in the country (or

in the case of the EEA, union of countries) in which the purchaser

resides; and

- Routine maintenance outlined in the operator’s guide must be

timely performed in order to maintain warranty coverage. BRP re-

serves the right to make warranty coverage contingent upon proof

of proper maintenance.

BRP will not honour this limited warranty to any private use owner or

commercial use owner if one of the preceding conditions has not been

met. Such limitations are necessary in order to allow BRP to preserve

both the safety of its products, and also that of its consumers and the

general public.

WHAT TO DO TO OBTAIN WARRANTY

COVERAGE

The customer must cease using the snowmobile upon the appearance

of an anomaly. The customer must notify a servicing LYNX Distributor

/ Dealer within two (2) months of the appearance of a defect, and pro-

vide it with reasonable access to the product and reasonable opportu-

nity to repair it. The customer must also present to the authorized

LYNX Distributor / Dealer, proof of purchase of the product and must

sign the repair / work order prior to starting the repair in order to vali-

date the warranty repair. All parts replaced under this limited warranty

become the property of BRP.

Note that the notification period is subject to the applicable national or

local legislation in customer's country.

266

WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty

are limited to, at its sole discretion, repairing parts found defective

under normal use, maintenance and service, or replacing such parts

without charge for parts and labour, at any authorized LYNX Distribu-

tor / Dealer during the warranty coverage period under the conditions

described herein. BRP’s responsibility is limited to making the required

repairs or replacements of parts. No claim of breach of warranty shall

be cause for cancellation or rescission of the sale of the snowmobile

to the owner. You may have other legal rights which may vary from

country to country.

In the event that service is required outside of the country of original

sale, or for EEA residents, if service is required outside of the EEA,

the owner will bear responsibility for any additional charges due to lo-

cal practices and conditions, such as, but not limited to, freight, insur-

ance, taxes, license fees, import duties, and any and all other financial

charges, including those levied by governments, states, territories and

their respective agencies.

BRP reserves the right to improve or modify products from time to time

without assuming any obligation to modify products previously

manufactured.

TRANSFER

If the ownership of a product is transferred during the warranty cover-

age period, this limited warranty, subject to its terms and conditions,

shall also be transferred and be valid for the remaining coverage peri-

od provided BRP or an authorized LYNX Distributor / Dealer receives

a proof that the former owner agreed to the transfer of ownership, in

addition to the coordinates of the new owner.

CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited

warranty, BRP suggests that you try to resolve the issue at the LYNX

Distributor / Dealer level. We recommend discussing the issue with

the authorized LYNX Distributor / Dealer's service manager or owner.

If the matter still remains unresolved, contact BRP by filling out the

customer contact form at www.brp.com or contact BRP by mail at one

of the addresses listed under the CONTACT US section of this guide.

267

ADDITIONAL TERMS AND CONDITIONS FOR FRANCE ONLY

The following terms and conditions are applicable to products sold in

France only:

The seller shall deliver goods that are complying with the contract and

shall be responsible for defects existing upon delivery. The seller shall

also be responsible for defects resulting from packaging, assembling

instructions or the installation when it is its responsibility per the con-

tract or if accomplished under its responsibility. To be compliant with

the contract, the good shall:

1. Be fit for normal use for goods similar thereto and, if applicable:

- Correspond to the description provided by the seller and have

the qualities presented to the buyer though sample or model;

- Have the qualities that a buyer may legitimately expect consid-

ering the public declarations of the seller, the manufacturer of

its representative, including in advertising or labeling; or

2. Have the characteristics mutually agreed upon as between the par-

ties or be fit for the specific use intended by the buyer and brought

to the attention of the seller and which accepted.

The action for failure to comply is prescribed after two years after de-

livery of the goods. The seller is responsible for the warranty for hid-

den defects of the good sold if such hidden defects are rendering the

good unfit for the intended use, or if they diminish its use in such a

way that the buyer would not have acquired the good or would have

given a lesser price, had he known. The action for such hidden defects

shall be taken by the buyer within 2 years of the discovery of the

defect.

268

BRP LIMITED WARRANTY USA AND

CANADA: 2024 LYNX® SNOWMOBILES

SCOPE OF THE LIMITED WARRANTY

Bombardier Recreational Products Inc. ("BRP") warrants its 2024

LYNX^® snowmobiles (“Product (s)”) sold by authorized BRP Dealers

(as hereinafter defined) in the United States of America ("USA") and in

Canada from defects in material or workmanship for the period and

under the conditions described below.

This limited warranty will become null and void if:

(1) the Product was used for racing or any other competitive activity,

at any point, even by a previous owner; or

(2) the Product has been altered or modified in such a way so as to ad-

versely affect its operation, performance or durability, or has been al-

tered or modified to change its intended use.

Non-factory installed parts and accessories are not covered under this

limited warranty. Please refer to the applicable parts and accessories

limited warranty text.

LIMITATIONS OF LIABILITY

TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY IS

EXPRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND

ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, IN-

CLUDING WITHOUT LIMITATION ANY WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE

IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE

LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CON-

SEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE

UNDER THIS WARRANTY. SOME STATES/PROVINCES DO

NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS AND EX-

CLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC

RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS

WHICH MAY VARY FROM STATE TO STATE, OR PROVINCE

TO PROVINCE.

Neither the distributor, any BRP dealer nor any other person has been

authorized to make any affirmation, representation or warranty regard-

ing the product, other than those contained in this limited warranty,

and if made, shall not be enforceable against BRP. BRP reserves the

right to modify this limited warranty at any time, being understood that

such modification will not alter the warranty conditions applicable to

the products sold while this warranty is in effect.

269

BRP LIMITED WARRANTY USA AND CANADA: 2024 LYNX^® SNOWMOBILES

EXCLUSIONS – ARE NOT WARRANTED

The following are not warranted under any circumstances:

Normal wear and tear;

–

Routine maintenance items, tune ups, adjustments;

–

Damage caused by failure to provide proper maintenance and/or

storage, as described in the Operator's Guide;

Damage resulting from removal of parts, improper repairs, service,

maintenance, modifications or use of parts or accessories not

manufactured or approved by BRP or resulting from repairs done

by a person that is not an authorized servicing BRP dealer;

Damage caused by abuse, abnormal use, neglect, use of the prod-

uct on surfaces other than snow, or operation of the product in a

manner inconsistent with the recommended operation described in

the Operator’s Guide;

Damage resulting from accident, submersion, fire, theft, vandalism

or any act of God;

Operation with fuels, oils or lubricants which are not suitable for

use with the product (see the Operator’s Guide);

Snow or water ingestion;

–

Incidental or consequential damages, or damages of any kind in-

cluding without limitation towing, storage, telephone, rental, taxi, in-

convenience, insurance coverage, loan payments, loss of time,

loss of income; and

Damage resulting from studs installed on tracks if the installation

does not conform to BRP’s instructions.

WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from (1) the date of delivery to

the first retail consumer, or (2) the date the product is first put into use,

whichever occurs first and for the applicable period below:

1. TWELVE (12) consecutive months, for private use or commercial

use owners. However, the warranty coverage period on a snowmo-

bile delivered between June 1^st and December 1^st of a given year

will expire November 30^th of the following year

2. For emission-related components, please also refer to the US

EPA Emission-Related Warranty.

The repair or replacement of parts or the performance of service under

this warranty does not extend the life of this limited warranty beyond

its original expiration date.

CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only if each of the following condi-

tions has been fulfilled:

270

BRP LIMITED WARRANTY USA AND CANADA: 2024 LYNX^® SNOWMOBILES

1. The Product must be purchased as new and unused by its first

owner from a Dealer authorized to distribute Products in the coun-

try in which the sale occurred (“Dealer”);

2. The BRP specified pre-delivery inspection process must be com-

pleted, documented and signed by the purchaser;

3. The Product must have undergone proper registration by an au-

thorized Dealer;

4. The Product must be purchased in the country in which the pur-

chaser resides;

5. Routine maintenance outlined in the Operator’s Guide must be

timely performed in order to maintain warranty coverage. BRP re-

serves the right to make warranty coverage contingent upon proof

of proper maintenance.

BRP will not honor this limited warranty to any private use owner or

commercial use owner if one of the preceding conditions has not been

met. Such limitations are necessary in order to allow BRP to preserve

both the safety of its products, and also that of its consumers and the

general public.

WHAT TO DO TO OBTAIN WARRANTY

COVERAGE

The customer must cease using the Product upon the appearance of

an anomaly, notify a servicing BRP Dealer within two (2) months of

the appearance of the anomaly and provide the Dealer with reason-

able access to the Product and reasonable opportunity to repair it.

The notification period is subject to the applicable national or local

legislation in customer's country.

The customer must also present to the Dealer, proof of purchase of

the Product and must sign the repair/work order prior to starting the re-

pair in order to validate the warranty repair.

All parts replaced under this limited warranty become the property of

BRP.

WHAT BRP WILL DO

To the extent permitted by law, BRP’s obligations under this warranty

are limited to, at its sole discretion, repairing or replacing parts found

defective under normal use, maintenance and service without charge

for parts and labor, at any authorized BRP Dealer during the warranty

coverage period under the conditions described herein. No claim of

breach of warranty shall be cause for cancellation or rescission of the

sale of the Product to the owner. You may have other legal rights

which may vary from country to country.

271

BRP LIMITED WARRANTY USA AND CANADA: 2024 LYNX^® SNOWMOBILES

In the event that service is required outside of the country of original

sale, the owner will bear responsibility for any additional charges due

to local practices and conditions, such as, but not limited to, freight, in-

surance, taxes, license fees, import duties, and any and all other finan-

cial charges, including those levied by governments, states, territories

and their respective agencies.

BRP reserves the right to improve or modify products from time to time

without assuming any obligation to modify products previously

manufactured.

TRANSFER

If the ownership of a product is transferred during the warranty cover-

age period, this limited warranty, subject to its terms and conditions,

shall also be transferred and be valid for the remaining coverage peri-

od provided BRP or an authorized LYNX Dealer receives a proof that

the former owner agreed to the transfer of ownership, in addition to

the coordinates of the new owner.

CONSUMER ASSISTANCE

In the event of a controversy or a dispute in connection with this limited

warranty, BRP suggests that you try to resolve the issue at the dealer-

ship level. We recommend discussing the issue with the authorized

dealer's service manager or owner.

If the matter still remains unresolved, contact BRP by filling out the

customer contact form at www.brp.com or contact BRP by mail at one

of the addresses listed under the CONTACT US section of this guide.

272

US EPA EMISSION-RELATED WARRANTY

Bombardier Recreational Products Inc. (“BRP”) warrants to the ulti-

mate purchaser and each subsequent purchaser that this new engine,

including all parts of its exhaust emission-control system and its evap-

orative emission-control system, meets two conditions:

1. It is designed, built, and equipped so it conforms at the time of sale

to the ultimate purchaser with the requirements of 40 CFR 1051

and 40 CFR 1060.

2. It is free from defects in materials and workmanship that may keep

it from meeting the requirements of 40 CFR 1051 and 40 CFR

1060.

Where a warrantable condition exists, BRP will repair or replace, as it

elects, any part or component with a defect in materials or workman-

ship that would increase the engine’s emissions of any regulated pol-

lutant within the stated warranty period at no cost to the owner,

including expenses related to diagnosing and repairing or replacing

emission-related parts. All defective parts replaced under this warranty

become the property of BRP.

For all emission-related warranty claims, BRP is limiting the diagnosis

and repair of emission-related parts to the authorized LYNX dealers,

unless for emergency repairs as required by item 2 of the following

list.

As a certifying manufacturer, BRP will not deny emission-related war-

ranty claims based on any of the following:

1. Maintenance or other service BRP or BRP's authorized facilities

performed.

2. Engine/equipment repair work that an operator performed to cor-

rect an unsafe, emergency condition attributable to BRP as long as

the operator tries to restore the engine/equipment to its proper con-

figuration as soon as possible.

3. Any action or inaction by the operator unrelated to the warranty

claim.

4. Maintenance that was performed more frequently than BRP

specify.

5. Anything that is BRP fault or responsibility.

6. The use of any fuel that is commonly available where the equip-

ment operates unless BRP written maintenance instructions state

that this fuel would harm the equipment’s emission control system

and operators can readily find the proper fuel. See maintenance in-

formation section and fuel requirements of fueling section.

Emiissiion-Related Warranty Period

The emission-related warranty is valid for the following period which-

ever comes first:

273

US EPA EMISSION-RELATED WARRANTY

Kilo

hours

months

meters

Exhaust emission-related

200

4000

components

Evaporative emission-related

N/A

components

Components Covered

The emission-related warranty covers all components whose failure

would increase an engine’s emissions of any regulated pollutant, in-

cluding the following listed components:

For exhaust emissions, emission-related components include any

engine parts related to the following systems:

- Air-induction system

- Fuel system

- Ignition system

- Exhaust gas recirculation systems

The following parts are also considered emission-related compo-

nents for exhaust emissions:

- Aftertreatment devices

- Crankcase ventilation valves

- Sensors

- Electronic control units

The following parts are considered emission-related components

for evaporative emissions:

- Fuel tank

- Fuel cap

- Fuel line

- Fuel line fittings

- Clamps*

- Pressure relief valves*

- Control valves*

- Control solenoids*

- Electronic controls*

- Vacuum control diaphragms*

- Control cables*

- Control linkages*

- Purge valves

- Vapor hoses

- Liquid/vapor separator

- Carbon canister

- Canister mounting brackets

274

US EPA EMISSION-RELATED WARRANTY

- Carburetor purge port connector

NOTE:

*As related to the evaporative emission control system

4. Emission-related components also include any other part whose

only purpose is to reduce emissions or whose failure will increase

emissions without significantly degrading engine/equipment

performance.

Limiited Applicabiiliity

As a certifying manufacturer, BRP may deny emission-related war-

ranty claims for failures that have been caused by the owner’s or oper-

ator’s improper maintenance or use, by accidents for which the

manufacturer has no responsibility, or by acts of God. For example, an

emission-related warranty claim need not be honored for failures that

have been directly caused by the operator’s abuse of the engine/

equipment or the operator’s use of the engine/equipment in a manner

for which it was not designed and are not attributable to the manufac-

turer in anyway.

If you have any question regarding your warranty rights and responsi-

bility or for the name and location of the nearest authorized BRP deal-

er, you should contact BRP by filling out the customer contact form at

www.brp.com or contact BRP by mail at one of the addresses listed

under the CONTACT US section of this guide, or call at

1-888-272-9222.

275

DATA PRIVACY INFORMATION

Bombardier Recreational Products inc., its affiliates and subsidiaries

(“BRP”) is committed to protecting your privacy and support a general

policy of openness about how we collect, use and disclose your per-

sonal information in the course of managing our relationship with you.

More details can be found by visiting BRP’s Privacy Policy at:

https://brp. com/en/privacy-policy. html or by scanning the QR

Code below.

Please be assured that we have appropriate security measures in

place to ensure that your personal information is protected against

loss and unauthorized access.

Your personal information that may be collected by BRP, directly from

you or from authorized dealers or authorized third parties, includes:

- Contact, Demographic & Registration Information (e.g., name,

full address, phone number, email, gender, ownership history, lan-

guage of communication)

- Vehicle Information (e.g., serial number, purchase and delivery

date, unit usage, vehicle location and movements)

- Third Party Information (e.g., information received from BRP

partners, joint-marketing activities information, social media)

- Technological Information (e.g., IP address, type of device, op-

erating system, browser type, webpages you view, cookies and

similar technologies when you use BRP or dealers’ websites or

mobile application)

- Interaction with BRP Information (e.g., information collected

when you call BRP’s in-house sales representatives, buy items on

a BRP web Site, sign up for BRP emails, participate in BRP-spon-

sored contests and sweepstakes or attend BRP-sponsored

events)

- Transactional Information (e.g., information necessary to handle

returns, payment information when you purchase our products or

services through our websites or mobile applications and other is-

sues related to your purchase of BRP products)

This information may be used and processed for the following

purposes:

- Safety & Security

- Customer Support for Sales & After Sales (e.g., complete or follow

up with you about your purchase or maintenance)

- Registration & Warranty

- Communication (e.g., sending you a BRP satisfaction survey)

- Online Behavioural Advertising, Profiling and Location-Based

Services

(e.g., offer customized experience)

- Compliance & Dispute Resolution

- Marketing & Advertising

- Assistance (e.g., help with any delivery issues, handle returns, and

other issues related to your purchase of BRP products).

278

DATA PRIVACY INFORMATION

We also may use personal information to generate aggregated or stat-

istical data that no longer identifies you personally.

Your personal information may be disclosed to the following:

BRP, BRP’s authorized dealerships, distributors, service pro-

viders, advertising & market research partners and other author-

ized third parties.

We may receive information about you from diverse sources, including

third parties, such as BRP’s authorized dealerships and partners, with

whom we offer services or engage in joint-marketing activities. We

may also receive information about you from social media platforms

such as Facebook and Twitter, when you interact with us on those

platforms.

Depending on the circumstances, your personal information may be

communicated outside the region where you reside. Your personal in-

formation is retained only for as long as necessary for the purpose for

which we obtained it and according to our retention policies.

To exercise your data privacy rights (e.g. right of access, right of recti-

fication), to withdraw your consent in order to be removed from the ad-

dress list for marketing purposes or for the satisfaction survey or for

general data privacy questions, please contact BRP’s Data Protection

Officer at or by mail at privacyofficer@brp.com or by mail at:

BRP Legal Service, 726 St-Joseph, Valcourt, Quebec, Canada, J0E

2L0.

When BRP processes your personal information, they do so in

compliance with its Privacy Policy available at: https://www.brp.

com/en/privacy-policy.html or by using the following

QR Code.

279

www.brp.com

Asiia Paciific

Australia

Level 26

477 Pitt Street

Sydney, NSW 2020

China

上海市徐汇区衡山路10号6号楼301

Rm 301, Building 6,

No.10 Heng Shan Rd,

Shanghai, China

Japan

21F Shinagawa East One Tower

2-16-1 Konan, Minato-ku-ku,

Tokyo 108-0075

New Zealand

Suite 1.6, 2-8 Osborne Street,

Newmarket, Auckland 2013

Europe, Middle East and Afriica

Belgium

Oktrooiplein 1

9000 Gent

Czech Republic

Stefanikova 43a

Prague 5

150 00

Germany

Itterpark 11

40724 Hilden

Finland

Isoaavantie 7

PL 8040

96101 Rovaniemi

France

Arteparc Bâtiment B

Route de la côte d'Azur,

13590 Meyreuil

280

CHANGE OF ADDRESS/OWNERSHIP

If your address has changed or if you are the new owner of the snow-

mobile, be sure to notify BRP by either:

- Notifying an authorized BRP snowmobile dealer or distributor.

- North America Only: calling at 1 888 272-9222.

- Mailing one of the change of address cards on the following pages

at one of the BRP addresses indicated in the Contact Us section of

this guide.

In case of change of ownership, please join a proof that the former

owner agreed to the transfer.

Notifying BRP, even after the expiration of the limited warranty, is very

important as it enables BRP to reach the snowmobile owner if neces-

sary, like when safety recalls are initiated. It is the owner’s responsibil-

ity to notify BRP.

STOLEN UNITS: If your personal snowmobile is stolen, you should

notify BRP or an authorized BRP snowmobile dealer. We will ask you

to provide your name, address, phone number, the vehicle identifica-

tion number and the date it was stolen.

282

Snowmobile Lynx UTILITY E-TEC SERIES. OPERATOR’S GUIDE (2024) - page 2